Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Jul 03, 2012, 04:29 AM
CO2X is offline
Find More Posts by CO2X
Registered User
CO2X's Avatar

v400 upper frame


Quote:
Originally Posted by fastfwd View Post
well after two days of installing new servos,and setup tweaking the v400 was flying strange, tipped and blades hit the grass ! CRAP ! bent upper frame,broke front mount, and pulled the stinking screws out of the servo holders. i took it completely apart and will start over later need a new upper frame and a better way to hold servos to holders. thinking ill use a small screw with a nut and washer. Ill just take my time and have fun doing it. Wish they made a better upper frame for V400
Fastfwd, Doubled-up your upper frame to make it stronger.
Sign up now
to remove ads between posts
Old Jul 03, 2012, 02:59 PM
fastfwd is offline
Find More Posts by fastfwd
Registered User
Quote:
Originally Posted by COCO2010 View Post
Fastfwd, Doubled-up your upper frame to make it stronger.
will do thanks !
Old Jul 03, 2012, 05:22 PM
segdohbird is offline
Find More Posts by segdohbird
Registered User
segdohbird's Avatar
Hey COCO2010,
I am in the process of double'n up the upper frame..So I want to paint the lower superframe.
Other than getting it powder coated what do you suggest in painting ??? and should i primer it first ??? What has everyone else done ???
Old Jul 03, 2012, 05:57 PM
Trelos05 is offline
Find More Posts by Trelos05
Registered User
Trelos05's Avatar
Quote:
Originally Posted by segdohbird View Post
How did you rate ????
I rate Coco frame 20 outta 10, so good I bought two !!!!!
Old Jul 03, 2012, 06:13 PM
fastfwd is offline
Find More Posts by fastfwd
Registered User

fusonics installed and new frame


here is a pic of the fusonics installed on V400 (before i tipped it and tore the screw out) and im making new upper frames,will make two lefts and two rights, Using the side panel off an old computer almost got them made just some clean up and paint, then to find enough screw with nuts and washers for the servo to servo holder connections think ill replace the feather shafts and the main shaft seeing how i happen to have new ones.
Last edited by fastfwd; Jul 04, 2012 at 01:47 AM.
Old Jul 03, 2012, 06:35 PM
segdohbird is offline
Find More Posts by segdohbird
Registered User
segdohbird's Avatar
Quote:
Originally Posted by Trelos05 View Post
I rate Coco frame 20 outta 10, so good I bought two !!!!!
And how did you finish them..(painting)
Old Jul 03, 2012, 06:41 PM
navigator2011 is online now
Find More Posts by navigator2011
Folding Spacetime
navigator2011's Avatar
Hey guys, have any of you ever had your heli shaking just because your gyro pots were turned too high? I have had this intermittent shaking situation that has gotten progressively worse. It seems a lot like when the blades are out of balance, except I don't think that really is the problem. Whilst flying, it gets worse when moving around through the wind, and it's seriously bad when I allow the heli to quickly drop altitude. But on the ground, it's so smooth you'd never think there was a problem. Oh, and the tail remains rock solid. I was poking around the 450 forum over at HF, and I saw it mentioned that cyclic gain can be tuned too high, and that got me wondering whether that is my problem as well with the V400.
Old Jul 03, 2012, 07:11 PM
fastfwd is offline
Find More Posts by fastfwd
Registered User
Quote:
Originally Posted by navigator2011 View Post
Hey guys, have any of you ever had your heli shaking just because your gyro pots were turned too high? I have had this intermittent shaking situation that has gotten progressively worse. It seems a lot like when the blades are out of balance, except I don't think that really is the problem. Whilst flying, it gets worse when moving around through the wind, and it's seriously bad when I allow the heli to quickly drop altitude. But on the ground, it's so smooth you'd never think there was a problem. Oh, and the tail remains rock solid. I was poking around the 450 forum over at HF, and I saw it mentioned that cyclic gain can be tuned too high, and that got me wondering whether that is my problem as well with the V400.
check the front motor mount even a small crack on mine did that.
Old Jul 03, 2012, 07:15 PM
fastfwd is offline
Find More Posts by fastfwd
Registered User
Quote:
Originally Posted by segdohbird View Post
Hey COCO2010,
I am in the process of double'n up the upper frame..So I want to paint the lower superframe.
Other than getting it powder coated what do you suggest in painting ??? and should i primer it first ??? What has everyone else done ???
where its aluminum, need to ruff it up a bit with some steel wool, then wash it with vinegar,then a good primer then paint away.
Old Jul 03, 2012, 10:29 PM
Heli Biggie is offline
Find More Posts by Heli Biggie
They call me plan B
Heli Biggie's Avatar
Lets talk tools , im to old for these little allen wrenches i need something with a handle.
Is this what i want , how do i know the sizes . I use all wrenches from the v400 for all my other helis . http://helidirect.com/align-extended...03-p-20343.hdx

Or this..http://helidirect.com/4in1-hexagon-s...ack-p-7777.hdx
Last edited by Heli Biggie; Jul 03, 2012 at 10:31 PM. Reason: More info
Old Jul 03, 2012, 10:36 PM
dgibbons is offline
Find More Posts by dgibbons
Registered User
dgibbons's Avatar
Hey guys

My buddy Dustin is having a 15% off sale on Walkera parts.

www.heli-heli.com

use code

walkera15
Old Jul 03, 2012, 10:41 PM
Heli Biggie is offline
Find More Posts by Heli Biggie
They call me plan B
Heli Biggie's Avatar
Or this http://helidirect.com/high-quality-h...oc=osc103_cart
Old Jul 03, 2012, 10:44 PM
fastfwd is offline
Find More Posts by fastfwd
Registered User
Quote:
Originally Posted by Heli Biggie View Post
Lets talk tools , im to old for these little allen wrenches i need something with a handle.
Is this what i want , how do i know the sizes . I use all wrenches from the v400 for all my other helis . http://helidirect.com/align-extended...03-p-20343.hdx

Or this..http://helidirect.com/4in1-hexagon-s...ack-p-7777.hdx
Hmmm i went to walmart and got the long handled ones, one set is metric, the other regular
Old Jul 03, 2012, 10:48 PM
dgibbons is offline
Find More Posts by dgibbons
Registered User
dgibbons's Avatar
Quote:
Originally Posted by Heli Biggie View Post
Lets talk tools , im to old for these little allen wrenches i need something with a handle.
Is this what i want , how do i know the sizes . I use all wrenches from the v400 for all my other helis . http://helidirect.com/align-extended...03-p-20343.hdx

Or this..http://helidirect.com/4in1-hexagon-s...ack-p-7777.hdx
I use these

http://helidirect.com/align-hexagon-...osc103_product
Old Jul 04, 2012, 12:23 AM
Heli Biggie is offline
Find More Posts by Heli Biggie
They call me plan B
Heli Biggie's Avatar
Cool , thanks , as long as i get the right sizes. I want 2 of the feathering shaft allen wreches , is that the 2.0?

Quote:
Originally Posted by dgibbons View Post


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Another new Walkera (V400D02)? GetterDragun Micro Helis 130 Apr 01, 2013 10:23 AM
Discussion Alternative canopies for Walkera V200D02, V400D02 JumboA5 Mini Helis 2 Mar 18, 2011 05:29 AM
Question Transport devices for 2x Walkera V400D02 & 2x Walkera V200D02 JumboA5 Electric Heli Talk 2 Dec 13, 2010 09:22 AM
Discussion Walkera new 3D flybarless V400D02 Naev 3D Electric Heli Flying 2 Oct 31, 2010 09:50 PM