Shop our Airplanes Products Drone Products Sales
Thread Tools
Old Feb 23, 2011, 12:15 PM
3rdeyepro is offline
Find More Posts by 3rdeyepro
Hovership
3rdeyepro's Avatar
What is the estimated cost? Also, what does the frame weigh?
Sign up now
to remove ads between posts
Old Feb 23, 2011, 12:55 PM
cactus is offline
Find More Posts by cactus
Registered User
Will it be possible to get the orange/black combo in an X layout with the front two booms orange?
Old Feb 23, 2011, 01:34 PM
DeXX is online now
Find More Posts by DeXX
DeXX's Avatar
What is the estimated cost?
http://www.kkmulticopter.com/index.p...d=88&Itemid=61

what does the frame weigh? around 240g-250g

Will it be possible to get the orange/black combo in an X layout with the front two booms orange?
yes, It is an option, X or + quad, as you want.... you will get it
RCG Plus Member
Latest blog entry: FPV Bullseye
Old Feb 25, 2011, 12:22 AM
victor66 is offline
Find More Posts by victor66
Registered User
Love it. Nice work!
Old Feb 25, 2011, 01:23 PM
3rdeyepro is offline
Find More Posts by 3rdeyepro
Hovership
3rdeyepro's Avatar
Can you do bright green arms/center pod?
Old Feb 25, 2011, 05:46 PM
DeXX is online now
Find More Posts by DeXX
DeXX's Avatar
Quote:
Originally Posted by 3rdeyepro View Post
Can you do bright green arms/center pod?
yes

I can do black, orange, blue, green, red, white, yellow and very dark purple(almost black)... for now

quad parts can be any combination of colors above, I paint with pigments so that the paint is not only on the surface, all layers are painted
RCG Plus Member
Latest blog entry: FPV Bullseye
Old Feb 26, 2011, 04:21 PM
demen is offline
Find More Posts by demen
Registered User
How do you mount the motors?
Old Feb 26, 2011, 05:40 PM
DeXX is online now
Find More Posts by DeXX
DeXX's Avatar
Quote:
Originally Posted by demen View Post
How do you mount the motors?
topside wall of the motor holder is thick enough to directly put a screw for wood (or some similar rough thread screw)
motores should have an X mount, motor holders are 45mm in diameter
RCG Plus Member
Latest blog entry: FPV Bullseye
Old Mar 04, 2011, 12:39 AM
saabguyspg is online now
Find More Posts by saabguyspg
saabguyspg's Avatar
dexx great work.... email sent, subscribed.

Love to see

1) enough space for full load of mikrokopter boards
2) separate compartment on the bottom for the battery (so I don't have to expose the top components to dusty environments.. once sealed up I can forget about it!
3) integrated fixed go pro mount (for camera WITHOUT the case because it will be protected by the fiberglass) this would be integrated with the battery area. you can leave it to the user to hot glue on a spare lens cover for the gopro easily purchased anywhere.

Steve
Site Sponsor
Old Mar 05, 2011, 08:33 AM
DeXX is online now
Find More Posts by DeXX
DeXX's Avatar
Quote:
Originally Posted by saabguyspg View Post
dexx great work.... email sent, subscribed.

Love to see

1) enough space for full load of mikrokopter boards
2) separate compartment on the bottom for the battery (so I don't have to expose the top components to dusty environments.. once sealed up I can forget about it!
3) integrated fixed go pro mount (for camera WITHOUT the case because it will be protected by the fiberglass) this would be integrated with the battery area. you can leave it to the user to hot glue on a spare lens cover for the gopro easily purchased anywhere.

Steve

thanks, e-mail answered


There is room for mikrokopter boards

separate compartment on the bottom.... working on it, and I'll try to integrate GoPro Mount...

I'll try to merge bottom compartment with landing gear, but .... I would need a little help from all of you.....

Since this bottom additional part is mostly for FPV, I would like to make something universal with enough space

Most important to me is size of batteries you use.... ? a little help please


tnx,
Denis
RCG Plus Member
Latest blog entry: FPV Bullseye
Old Mar 05, 2011, 04:18 PM
saabguyspg is online now
Find More Posts by saabguyspg
saabguyspg's Avatar
hey dex, usually if you are lifting anything most of us use a 4S pack.

I use anywhere from 4s2200 to 4s4000 packs. I do have 4xs 5300 packs too so I would say that is the max for me. Anything more than that and you are lifting too much battery IMHO

I would really love to see just a square section that straps to the bottom of your quad. 7" square should do. This sqaure section would have an angled part on the front. In this angled part you would have a hole for the go pro to see through. behind that and indside the frame is where you would put a sorbothane pad, on top the pad goes the go-pro and a simple velcro strap over the go pro to hold it in place.

the bottom of this square would be flat such that you can just land on its belly.

the reason I want it square is so that you can move the battery back to compensate for the go pro weight up front....

Steve... just some thoughts..
Site Sponsor
Old Mar 08, 2011, 11:50 AM
Steph280 is offline
Find More Posts by Steph280
1.21 Gigawatts!
Steph280's Avatar
ok we all hate to ask this, but it happens to everyone...

What is the crash survivability of the frame? Does it offer enough protection for the controller boards?

Batteries: I use 3s-5000 or 4s-3300-4000.
Old Mar 08, 2011, 12:01 PM
fcharp is offline
Find More Posts by fcharp
Registered User

Extended arms?


Dex,

Is it possible to slightly extend the arms? So that one could fit 1245 propellers?
BTW, very nice work. Having personally lost a hex at sea (pilot error) and because we have lots of lakes in Canada, this is something I am very interested in. I just placed an order for 2 of them on your site....

Thanks,
Frederic
Old Mar 09, 2011, 10:52 PM
DeXX is online now
Find More Posts by DeXX
DeXX's Avatar
Quote:
Originally Posted by saabguyspg View Post
I would really love to see just a square section that straps to the bottom of your quad. 7" square should do......
just a square?

basically your advice is accepted thx., just the section will follow contours of the body....


Quote:
Originally Posted by Steph280 View Post
ok we all hate to ask this, but it happens to everyone...

What is the crash survivability of the frame? Does it offer enough protection for the controller boards?
pod is very strong, there is more than enough protection for the board ....

model is made with a weakened one link, tubes are the weakest, cheapest and the easiest to change
so that survival is good, and when it breaks repairs are cheap and fast, just change the tube in a few minutes


Quote:
Originally Posted by fcharp View Post
Dex,

Is it possible to slightly extend the arms? So that one could fit 1245 propellers?
yes, shaft to shaft diameter can be from 46cm to 110cm
it just depends on the length of the tube...







I hope I answered all of the private messages... if not, remind me

Questions and orders..: dex@dexmodels.com ....here I answer a lot faster




and just to mention, I'm looking for dealers or group buyers
if you order 10 models in the package, you get 20% off
RCG Plus Member
Latest blog entry: FPV Bullseye
Old Mar 09, 2011, 11:11 PM
saabguyspg is online now
Find More Posts by saabguyspg
saabguyspg's Avatar
yes Dexx sorry... I mean a nicely formed pod with just the battery and say go pro compartment...

anyway your work is great! I am sure it will be good!

Steve
Site Sponsor


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Quad brushless motors and quad ESC wiring whatala Power Systems 11 Dec 28, 2015 04:51 PM
Build Log STM8s Quad-copter "Quad-radic" Edftakeoff Multirotor Talk 4 May 17, 2010 04:09 AM
Discussion New Dex Blades in Stock Now johnIn2SonAZ Micro Helis 0 Jul 01, 2009 06:12 AM
Sold DEX Blades for Walkera 4G3, 4#3a/b Steve_C Aircraft - Electric - Helis (FS/W) 4 Feb 09, 2009 09:09 PM
quad cdr quad esc how many poly cells? captinnitro Power Systems 2 Apr 04, 2005 09:37 PM