Thread Tools
This thread is privately moderated by mcross, who may elect to delete unwanted replies.
Old Dec 27, 2010, 07:01 PM
mcross is offline
Find More Posts by mcross
For Sale-everything over 250 g
Data

Bricks!


E-Hori-zone micro bricks for fixed wing micros. ********click ^ comments!********
What's what and how to tell them apart.
>5 different boards and >7 different versions are or have been available.

Please post any brick info you feel should be added.
Last edited by mcross; Mar 03, 2011 at 07:39 AM.
Sign up now
to remove ads between posts
Old Dec 27, 2010, 07:06 PM
mcross is offline
Find More Posts by mcross
For Sale-everything over 250 g

#1 Minium


Parkzone Minium 3
3.3 grams
3 channel, aileron, elevator, throttle
2.4 but not DSM or DSM2
Works only with Tx shown
Used in the Cessna and Citabria
Motor wires are soldered to the board
Board marked on bottom: 24R3V7

Arcox sells a chip to add taileron mix, channel swap and model memory to the Tx.
Last edited by mcross; Dec 30, 2010 at 05:37 PM.
Old Dec 27, 2010, 07:09 PM
mcross is offline
Find More Posts by mcross
For Sale-everything over 250 g

#2 Vapor (non-green dot)


2.4 DSM2
3.4 grams
3 Channel Aileron, elevator, throttle
2 position connector for motor wires. No 3rd hole for 3 position connector.
No extra channels if the led flashes when powered up, this is the first version of the software.
Board markings: 24R5C V05

Brushless convertion thread https://www.rcgroups.com/forums/showthread.php?t=896564
will work on #1, #2, #3, and #4
Last edited by mcross; Dec 30, 2010 at 05:32 PM.
Old Dec 27, 2010, 07:19 PM
mcross is offline
Find More Posts by mcross
For Sale-everything over 250 g

#3 Green dot


2.4 DSM2
3.4 grams
5 channel, aileron, elevator, throttle, rudder and ch 5. Rudder and ch 5 require that you add connectors to the board.
Led waits ~5 seconds before it flashes for bind, this is the newer software with 5 channels.
I have one of these NIB without the green dot but it does have the extra channels and the ~5 second delay before bind.
2 postion motor connector with no 3rd hole. (ESC is 1 amp).
Board markings: 24R5C V05, 24R5C V07 (often covered by the green dot)

Pinout photo courtesy of I R Irv, thanks Todd!
Connector kit available here: http://www.rc-connectors.com/index.p...a55jenqmh7ck44
Note that the pinout is different from the AR6400 board.
Brushless convertion thread https://www.rcgroups.com/forums/showthread.php?t=896564 (will work on #1, #2, #3, and #4)
Last edited by mcross; Jul 17, 2011 at 06:08 PM.
Old Dec 27, 2010, 07:24 PM
mcross is offline
Find More Posts by mcross
For Sale-everything over 250 g

#4 AR6400 based 3 channel


2.4 DSM2
3 channel aileron, elevator and throttle.
Has on board servo reversing
No extra connectors installed.
Doesn't seem to have extra channels like the green dot.
Doesn't seem to have brushless capabilty like the ar6400.
2 position motor connector with a 3rd unused hole for a 3 position connector. (ESC is 2 amps)
Board markings: 24R6CV2 (under FCC ID label)
Last edited by mcross; Jul 17, 2011 at 06:09 PM.
Old Dec 27, 2010, 07:28 PM
mcross is offline
Find More Posts by mcross
For Sale-everything over 250 g

#5 ar6400


2.4 DSM2
6 channels. Onboard servos are rudder and elevator.
3 position motor connector. (2amp brushed)
Features include reversible on board servos, can drive a brushless esc, reversed aileron and more.
Board markings: 24R6CV2
Link to instructions http://www.horizonhobby.com/ProdInfo...0-L-Manual.pdf
Note that there were several early versions of the instructions that had errors. If you buy old stock use the link to be sure you have correct information!
Brick orientation for elevon mix with DX7: https://www.rcgroups.com/forums/show...penguin&page=8
Last edited by mcross; Jul 17, 2011 at 09:03 AM.
Old Dec 28, 2010, 06:35 PM
mcross is offline
Find More Posts by mcross
For Sale-everything over 250 g

Ar6400l


2.4 DSM2
Long throw version of the AR6400.
6 channels. Onboard servos are rudder and elevator.
3 position motor connector. (2amp brushed)
Features include reversible on board servos, can drive a brushless esc, reversed aileron and more.
Board markings: 24R6CLV8, 24R6CLV11
Link to instructions http://www.horizonhobby.com/ProdInfo...0-L-Manual.pdf
Note that there were several early versions of the instructions that had errors. If you buy old stock use the link to be sure you have correct information!
Photo mounted in an UM 4-Site, courtesy of Tim Wolff.
Last edited by mcross; Jul 17, 2011 at 09:03 AM.
Old Dec 28, 2010, 06:35 PM
mcross is offline
Find More Posts by mcross
For Sale-everything over 250 g

Ar6400lbl


2s long throw with built in 3 amp brushless controller.
Last edited by mcross; Jan 01, 2011 at 04:09 PM.
Old Dec 28, 2010, 06:36 PM
mcross is offline
Find More Posts by mcross
For Sale-everything over 250 g
AR6400T
1S with twin brushed motor outputs, used in UM Mosquito
Last edited by mcross; Mar 03, 2011 at 07:41 AM.
Old Dec 28, 2010, 06:36 PM
mcross is offline
Find More Posts by mcross
For Sale-everything over 250 g
...
Old Dec 30, 2010, 10:15 PM
Tim Wolff is offline
Find More Posts by Tim Wolff
Gravity is a harsh mistress.
Tim Wolff's Avatar
Here's a shot of the AR6400L mounted in my UM 4-Site. Numbering behind the wires and pink dot is 24R6CLV8. Feel free to move the photo and nuke this post if you like.
Old Jan 01, 2011, 04:03 PM
mcross is offline
Find More Posts by mcross
For Sale-everything over 250 g
Thanks Tim!
Old Jan 15, 2012, 04:44 PM
glewis is offline
Find More Posts by glewis
Or current resident
glewis's Avatar
So the #3 green dot 24R5C V07 board does not support servo reversing?
I can't seem to get mine to work. It does the 5 second delay when binding so I'm assuming it is the same one you listed.
Glenn
Old Jan 15, 2012, 05:50 PM
mcross is offline
Find More Posts by mcross
For Sale-everything over 250 g
servo reversing started at the AR6400 based 3 channel #4. Green dots are not reversible.

Does it have 3 holes for the motor connector with 2 used for the connector (one hole unused)? If so it's a #4 and reversible.
If it has only 2 holes for the motor connector and the 5 second delay it's a green dots and not reversible.
Old Jun 04, 2012, 07:56 PM
minimicrorc is offline
Find More Posts by minimicrorc
Registered User
Quote:
Originally Posted by mcross View Post
servo reversing started at the AR6400 based 3 channel #4. Green dots are not reversible.

Does it have 3 holes for the motor connector with 2 used for the connector (one hole unused)? If so it's a #4 and reversible.
If it has only 2 holes for the motor connector and the 5 second delay it's a green dots and not reversible.
not even withe reversing using the radio, and I thought the green dot brick was rated at 2 amps

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Wanted Dead / Fried Parkzone Bricks ..need servo parts kerrylaw Aircraft - Electric - Micro & Indoor Airplanes (FS/W) 5 May 24, 2016 11:56 PM
Discussion Where To Buy AR6400 Bricks FANtastic Scratchbuilt Indoor and Micro Models 14 Dec 02, 2010 03:58 PM
Sold All of my UM Stuff 3 bricks, 2 servos, motor, 4 Hyperion batteries jmrust Aircraft - Electric - Micro & Indoor Airplanes (FS/W) 3 Nov 27, 2010 08:19 AM
Discussion DX7 & Bricks - What am I missing? elvill Scratchbuilt Indoor and Micro Models 12 Nov 17, 2010 05:11 PM