New Products Flash Sale
Thread Tools
Old Sep 12, 2012, 07:06 AM
gs550t1981 is offline
Find More Posts by gs550t1981
Beginner Pilot
Lol how do I know what is compatible with my esc if I don't know what esc it is? It is a good esc, maybe I'll just leave it be for now.....
Sign up now
to remove ads between posts
Old Sep 12, 2012, 10:58 AM
mdugas is offline
Find More Posts by mdugas
Registered User
hi yellow and 30,could be a hobbywing esc.hobbypartz sells those low cost but
good quality .was popular for building heli on budget and as a replacment
i wont swear to it but if i remember right the turnigy program card is compatable
Last edited by mdugas; Sep 12, 2012 at 11:12 AM.
Old Sep 12, 2012, 12:44 PM
Jay Santos is offline
Find More Posts by Jay Santos
Heli Slinger
Jay Santos's Avatar
Quote:
Originally Posted by gs550t1981 View Post
Lol how do I know what is compatible with my esc if I don't know what esc it is? It is a good esc, maybe I'll just leave it be for now.....
If you don't know who made your ESC, how can we suggest the correct programming card? The cards are inexpensive so you can buy a popular one that works with a lot of ESCs and take your chance.
Old Oct 30, 2012, 12:05 AM
totse is offline
Find More Posts by totse
Registered User
I havent seen any post on people flying this inverted?
What are the capabilities of this heli?
Old Oct 31, 2012, 05:37 PM
bark is online now
Find More Posts by bark
Registered User

binding


Hello all,
I have scanned through the thread and have not seen where anyone has posted the binding procedure for the Hausler T-6A transmitter with the R-6X rcvr. I got a new transmitter and cannot figure out how to bind the two together. Help would be greatly apreciated.
Old Oct 31, 2012, 05:59 PM
bark is online now
Find More Posts by bark
Registered User
Quote:
Originally Posted by bark View Post
Hello all,
I have scanned through the thread and have not seen where anyone has posted the binding procedure for the Hausler T-6A transmitter with the R-6X rcvr. I got a new transmitter and cannot figure out how to bind the two together. Help would be greatly apreciated.
found it
Old Nov 02, 2012, 06:55 AM
yoreh is offline
Find More Posts by yoreh
Registered User

Motor replacement shaft


Hi guys, any idea where i could get a replacement shaft for my Hausler 450 motor? the motor is NEO 450 4000kv, shaft diameter is 3.17mm , don't know the right length as it was broken during a stupid crash and the upper part of the shaft (with the pinon) got lost...

Thanks.
Old Nov 02, 2012, 03:11 PM
fuggetaboutit is online now
Find More Posts by fuggetaboutit
Registered User
Try Cermark.com or GyroHobbies.com for your info, not sure if you can get just the Shaft. Other than buying local, these are the places I get parts.
Old Apr 03, 2013, 02:23 PM
george12flyer is offline
Find More Posts by george12flyer
Registered User

blades won't stop rotating


Need Help on how to reset speed control or down load program on P.C.
Old Apr 05, 2013, 12:37 PM
fuggetaboutit is online now
Find More Posts by fuggetaboutit
Registered User
Programming Instructions:
1. Connect your motor and receiver to the speed controller, but
do not connect the battery yet.
2. Turn on your transmitter and move the throttle stick to the full
throttle position (full up).
3. If you are using a separate receiver battery pack instead of
using the BEC, connect the receiver pack and turn it on
4. Connect your battery and the controller will initialize with a
musical tone.
5. Secure the airplane and stay clear of the propeller
6. The ESC will issue a series of one to three beeps
representing the three items that can be programmed. Each
is repeated twice. When you hear the option you wish to
program (summarized in the table below), move the throttle
stick to the full down position to program the option.
Old Apr 09, 2013, 08:42 PM
ASTREA1 is offline
Find More Posts by ASTREA1
A&P in training
ASTREA1's Avatar
Quote:
Originally Posted by george12flyer View Post
Need Help on how to reset speed control or down load program on P.C.



Here is the setup, more than likely need to reset the "Throttle Range"

https://www.rcgroups.com/forums/show...mentid=3588554
Old Apr 14, 2013, 10:12 PM
Tail Wheel is offline
Find More Posts by Tail Wheel
Registered User
Tail Wheel's Avatar
Quote:
Originally Posted by totse View Post
I havent seen any post on people flying this inverted?
What are the capabilities of this heli?
Out of the box, and after double checking the setup, it is capable of mild, 3D manuevers.

Should be able to pull off anything an Align Trex 450 SE can do.


Stock RTF Hausler 450.wmv (3 min 21 sec)
Old Apr 20, 2013, 05:21 PM
Tail Wheel is offline
Find More Posts by Tail Wheel
Registered User
Tail Wheel's Avatar
Is Cermark still up, and running? I emailed them a month ago, but no response. Mr.Chao hasn't been on here like he used to be.
Old May 30, 2013, 07:00 PM
HelisRock is offline
Find More Posts by HelisRock
Registered User
HelisRock's Avatar
Quote:
Originally Posted by Tail Wheel View Post
Is Cermark still up, and running? I emailed them a month ago, but no response. Mr.Chao hasn't been on here like he used to be.
Same thing here, used "contact us" on their web page a week or so ago, but no response...
Old May 31, 2013, 01:33 AM
whitehedr is offline
Find More Posts by whitehedr
Retired Old Guy
whitehedr's Avatar
I am pretty sure Cermark is Kaput. I tried to call about 3 weeks ago and the phone just rang. No VM or answering machine. I tried maybe three different times with the same result. I have also seen other posts about unanswered emails and contact attempts.

ROG


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Wanted Align 450 SE v2 head block zen@lanset.com Aircraft - Electric - Helis (FS/W) 2 Oct 02, 2010 10:59 PM
Off Site Align T-Rex 450 SE V2 Complete RTF RC Helicopter Tom Z Aircraft - Electric - Helis (FS/W) 1 Sep 25, 2010 09:07 PM
For Sale Trex 450 se v2 $125 magee8578 Aircraft - Electric - Helis (FS/W) 1 Sep 04, 2010 09:36 PM
Discussion Copter X 450 SE V2 or Trex 450 SE V2 Razor04 Mini Helis 6 Aug 03, 2009 08:36 AM