Thread Tools
Feb 01, 2013, 06:33 AM
Registered User
Hi, Im from Spain.
Ive got this "Ninco Air AluOne G" from a spanish shop.

Its a clone of the DoubleHorse 9100, it cost me like 50.

Everething looks fine, but I think I`ll give it a try for the swashplate modificatios because its too lazy to go foward and backwards.
Sorry about my bad english.

Greeting from Spain.
Sign up now
to remove ads between posts
Feb 01, 2013, 07:45 AM
Registered User
Quote:
Originally Posted by Miscelaneo View Post
Hi, Im from Spain.
Ive got this "Ninco Air AluOne G" from a spanish shop.

Its a clone of the DoubleHorse 9100, it cost me like 50.

Everething looks fine, but I think I`ll give it a try for the swashplate modificatios because its too lazy to go foward and backwards.
Sorry about my bad english.

Greeting from Spain.

Definitely the same heli. Balance the blades while you're at it. Mine was way off but can't expect to much from a cheap RC toy.

After you do the swashplate mod, it will be more responsive and faster. It'll hover perfectly as well with no left drift like mine did.
Feb 01, 2013, 04:43 PM
Registered User
Here is a comparation I just made about the adjustment of the swashplate.

NincoAir AluOne G DoubleHorse 9100 Clone "mod" (0 min 38 sec)
Apr 01, 2013, 03:42 PM
Registered User
Hi all.
My hover had crashed and 9100-06 (connect buckle) item broked. Today I bought new one and repair my hover. But it seems like I did smth wrong. When it must go forward it's doing some strange thing (video). Can you explain what I did wrong?
hover 9100 (0 min 38 sec)

Sorry for quality (it's night here now)
Photo can show how I "repaired" it.

Also, sorry for bad explaining.
And greeting from Ukraine
Last edited by Allexandr; Apr 01, 2013 at 03:48 PM.
Apr 02, 2013, 10:37 AM
Registered User
In better quality.
It begin to move up\down this then I'm pushing "Move Forward".
What can it be? I think, that smth blocks movement of this thing.
9100 hover (0 min 40 sec)
Apr 02, 2013, 11:28 AM
"Watch this!.... Oh crap"
jhebbel's Avatar
Quote:
Originally Posted by Allexandr View Post
In better quality.
It begin to move up\down this then I'm pushing "Move Forward".
What can it be? I think, that smth blocks movement of this thing.
http://www.youtube.com/watch?v=TUVDH...ature=youtu.be
1st your main shaft collar is loose, it appears when you move elev control the whole shaft is shifting, you need to pull the shaft up then tighten the collar. 2nd a shot or angle that shows your servo would be better to make sure you are not binding or reaching extent.
Apr 02, 2013, 12:30 PM
Registered User
Good day. Thank you for your response.
I maybe I didn't understand something. This is my mechanism. What should I tighten?
All bolts are on the same places where they were. (As I can see)
Apr 02, 2013, 01:04 PM
"Watch this!.... Oh crap"
jhebbel's Avatar
Quote:
Originally Posted by Allexandr View Post
Good day. Thank you for your response.
I maybe I didn't understand something. This is my mechanism. What should I tighten?
All bolts are on the same places where they were. (As I can see)
The brass collar on the main shaft should have grub nuts or screws to lock it to the main shaft to prevent vertical shaft movement.
Apr 05, 2013, 06:41 AM
Registered User
Quote:
Originally Posted by Allexandr View Post
Good day. Thank you for your response.
I maybe I didn't understand something. This is my mechanism. What should I tighten?
All bolts are on the same places where they were. (As I can see)
I can see your swashplate is a little bit open, u can see the metal between, try to tighten.
Apr 05, 2013, 09:38 AM
"Watch this!.... Oh crap"
jhebbel's Avatar
Quote:
Originally Posted by Miscelaneo View Post
I can see your swashplate is a little bit open, u can see the metal between, try to tighten.
I think you are referring to the shaft collar as there is nothing to tighten on a swashplate.
Apr 05, 2013, 04:04 PM
Registered User
Quote:
Originally Posted by jhebbel View Post
I think you are referring to the shaft collar as there is nothing to tighten on a swashplate.
The swashplate is made of two pices. They can get loose. They should be together, without any metal showing between them.
Apr 07, 2013, 09:07 AM
Registered User
With the help of jhebbel, I understand that problem is in the servo. cogwheel is demaged and I think, that I need to replace it.

Apr 16, 2013, 09:00 AM
Registered User

DH-9100 Problem


Hi everyone,

I have a difficulty with my DH-9100 RC helicopter. I took it for a spin the first time last weekend and after 10mins trying it out the battery seemed to be dying so I turned it off and put it on charge. Soon after putting it on charge it marked that it charged. I removed it and switched it on to test it out however the DH-9100 starts to function but it does not have enough power to lift off the ground. I took the RC helicopter at work to find out that there is a problem with the charging board so I charged it automatically with a power supply and I read it with a voltage meter and the battery was charged. Then I removed it and switched it on to test it but the voltage of the battery drops down very very fast after 2-3 tryx maximum it just decreases..in 2mins the voltage drops from 7.86v to 5.6v thus the RC helicopter does not have enough power to lift off the ground. I dont know whether the battery is defective or whether something in the circuit board or motor is causing this. Any clues maybe you have experienced it sometime or another.

Thanks,
Apr 16, 2013, 09:18 AM
"Watch this!.... Oh crap"
jhebbel's Avatar
Quote:
Originally Posted by mal1990p View Post
Hi everyone,

I have a difficulty with my DH-9100 RC helicopter. I took it for a spin the first time last weekend and after 10mins trying it out the battery seemed to be dying so I turned it off and put it on charge. Soon after putting it on charge it marked that it charged. I removed it and switched it on to test it out however the DH-9100 starts to function but it does not have enough power to lift off the ground. I took the RC helicopter at work to find out that there is a problem with the charging board so I charged it automatically with a power supply and I read it with a voltage meter and the battery was charged. Then I removed it and switched it on to test it but the voltage of the battery drops down very very fast after 2-3 tryx maximum it just decreases..in 2mins the voltage drops from 7.86v to 5.6v thus the RC helicopter does not have enough power to lift off the ground. I dont know whether the battery is defective or whether something in the circuit board or motor is causing this. Any clues maybe you have experienced it sometime or another.

Thanks,
Not sure what the chemistry is of the battery you are using, but if it is LiPo then it sounds like you discharged it too far. Unlike other chemistries if you run a LiPo past 80% it destroys the battery. Also don't ever charge a battery with just a power supply, this can also ruin the battery by over amping it.
May 13, 2013, 12:47 PM
Registered User
New here, and I have a DH 9116 on the way to my door. This is my first Heli, and I'm pretty stoked about it


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Fast Lane Proton 3 Channel Co-Ax From Toys R Us edwong3 Coaxial Helicopters 13 Nov 15, 2010 05:57 PM
Discussion How to seperate channel 6 from channel 1 in Futaba T6EXHP..?? joy4u Radios 5 Oct 14, 2010 11:31 PM
Discussion transition from three to four channel love2fish93 Electric Plane Talk 21 Sep 28, 2008 07:34 PM
Wanted WANTED: 3 channel{or four} aircraft with ailerons- Will trade plus money Lizard Boy Aircraft - Electric - Jets (FS/W) 0 Oct 02, 2007 08:29 PM