Shop our Airplanes Products Drone Products Sales
Thread Tools
Dec 17, 2010, 03:51 PM
Registered User
Discussion

Hobbywing Pentium 40A Brushless ESC with UBEC


Just received this controller from HobbyPartz. It has an encapsulated coil wound into the receiver leads. Anybody know what this is for and if it is necessary?
Sign up now
to remove ads between posts
Dec 17, 2010, 04:26 PM
Registered User
Dr Kiwi's Avatar
It is a toroid coil to reduce interference... beyond that, ask someone smarter than I am!

From an RC Groups post:

It is more likely that the ESC noise is radiating from the motor wires and being picked up by your Rx antenna and/or servo wires. Toroid rings can be effective in reducing the noise conducted by the servo wires. They should be placed as close to the servo plugs (where they connect to the Rx) as practical. The energy radiated by the motor mains can be reduced substantially by simply twisting them together. This simple expedient may be enough to resolve the problem you have experienced.
Dec 17, 2010, 04:29 PM
Registered User
That would be a "ferrite ring". It suppresses high frequency noise in electronic circuits.
I'm unclear if it is needed with 2.4GHz.
Dr.Kiwi beat me to it.
Last edited by gofish; Dec 17, 2010 at 04:30 PM. Reason: tad late
Dec 17, 2010, 08:29 PM
Sleepy Hollow, IL
The ferrite rings are mainly used on ESCs that have a switching supply for the BEC. The ring as others have stated is to reduce the switching noise from entering the receiver.

Since linear BECs don't have this switching noise the ferrite rings are really not needed.

ampmaker
Dec 18, 2010, 05:26 PM
**** 37130 ****
RobC(UK)'s Avatar
Quote:
Originally Posted by frdeluca1 View Post
Just received this controller from HobbyPartz. It has an encapsulated coil wound into the receiver leads. Anybody know what this is for and if it is necessary?
If you decide to leave the ferrite ring in place be sure to tie it down to the airframe!

I have seen 2 planes disconnect their Rx power due to the ring flailing about and pulling the plug out of the RX. Both times it happened during violent manoeuvres so the control surfaces stayed at near full deflection!
Dec 20, 2010, 01:32 AM
Hold Down The West!
cryhavoc38's Avatar
With switch mode bec's, the bec can introduce high frequency noise into an FM reciever, but 2.4ghz systems aren't affected by these high frequencies.

For 2.4ghz, you can remove the coil ( I use a pair of diagonal cutters to break the coil since they are rather brittle and soft.

for fm systems, its a must that you keep it on.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Sold Used 1x HobbyWing Pentium 60amp opto Esc w/ UBEC $30 shipped jmrust Aircraft - Electric - Power Systems (FS/W) 7 Dec 06, 2010 08:47 PM
Alert $19.44 only at oomodel,hobbywing pentium 40A brushless ESC oomodel.com Hot Online Deals 0 Sep 18, 2010 09:56 AM
Hobbywing pentium 40A brushless ESC ONSALE!! targethobby Aircraft - General - Miscellaneous (FS/W) 0 Apr 26, 2010 02:11 AM
Sold Hobbywing 40A Pentium ESC heychas Aircraft - Electric - Power Systems (FS/W) 1 Mar 11, 2010 01:06 PM
Sold Hobbywing Pentium 40A ESC w/ 3A BEC awayne Aircraft - Electric - Power Systems (FS/W) 4 Dec 07, 2009 05:12 PM