Thread Tools
Old Jan 12, 2011, 09:48 AM
kman24 is offline
Find More Posts by kman24
Addicted To Flying Foam
kman24's Avatar
Quote:
Originally Posted by luvmykids2 View Post
Are there parts out there anywhere for this plane?
I would imagine that Nitroplanes could get you a part. You may have to call them directly.
Sign up now
to remove ads between posts
Old Jan 13, 2011, 10:29 PM
kman24 is offline
Find More Posts by kman24
Addicted To Flying Foam
kman24's Avatar

Reverse Flap Servo


I am getting ready to install the flaps on mine and was contemplating whether to try and get a reversed servo or a y-cable with a servo reversing module. After doing a little searching, I found some good instructional guides on how to reverse a typical servo by swapping a couple pairs of wires inside. So, I tried it and it worked

Now I just need to install the servos and the other hardware, but I am still missing one of the flap hinges. I actually contacted Nitroplanes a few weeks ago about getting another hinge and they said they would mail me one. But, I haven't seen it come yet I suppose I could just install the 2 outer hinges and install an ordinary control horn in the middle of each flap and attach it to the servos. It would look as clean but it would work.

KMan
Old Jan 21, 2011, 02:46 PM
Rimmyman is offline
Find More Posts by Rimmyman
Registered User
Quote:
Originally Posted by kman24 View Post
I am getting ready to install the flaps on mine and was contemplating whether to try and get a reversed servo or a y-cable with a servo reversing module. After doing a little searching, I found some good instructional guides on how to reverse a typical servo by swapping a couple pairs of wires inside. So, I tried it and it worked

Now I just need to install the servos and the other hardware, but I am still missing one of the flap hinges. I actually contacted Nitroplanes a few weeks ago about getting another hinge and they said they would mail me one. But, I haven't seen it come yet I suppose I could just install the 2 outer hinges and install an ordinary control horn in the middle of each flap and attach it to the servos. It would look as clean but it would work.

KMan
why go through all that trouble? I just installed mine facing the same direction. the flaps move in much the same way, but no additional or costly work.

I used the outer 3 to secure the flap hinges and the middle is just the control throw.

granted, i'm a novice pilot, but it works great work me
Old Jan 21, 2011, 03:46 PM
kman24 is offline
Find More Posts by kman24
Addicted To Flying Foam
kman24's Avatar
I reversed the one servo just to see if I could do it. I saw that it could be done by just swapping a couple pairs of wires inside. It didn't take long, only about 15 minutes and it it just required a screwdriver and a soldering iron. Here is a video on how to do it if you are ever interested.

How to REVERSE a Servo. (4 min 32 sec)


I will probably just do what you did and only attach the outer 2 hinges with a control horn in the middle. Should do the trick.

KMan
Old Jan 21, 2011, 07:42 PM
Rimmyman is offline
Find More Posts by Rimmyman
Registered User
Quote:
Originally Posted by kman24 View Post
I reversed the one servo just to see if I could do it. I saw that it could be done by just swapping a couple pairs of wires inside. It didn't take long, only about 15 minutes and it it just required a screwdriver and a soldering iron. Here is a video on how to do it if you are ever interested.

I will probably just do what you did and only attach the outer 2 hinges with a control horn in the middle. Should do the trick.

KMan
oh i've done that to a servo, its a good tip. just have steady hands.

my flaps are sturdy and work well, you will enjoy landing with them though. its truly inspiring to see
Old Jan 30, 2011, 02:55 PM
kman24 is offline
Find More Posts by kman24
Addicted To Flying Foam
kman24's Avatar
I finally got my flaps installed and working. This is my first plane with flaps so I am anxious to try them out soon. I had Nitroplanes send me a replacement flap hinge since I was missing one from the original kit. Took them a little while, but they came through for me (thanks Nitroplanes!!!). Right now, I have the flaps set for 50% travel. This gives me about a 45 degree angle from level. Does this sound reasonable for those who are using flaps on this plane? Or do I need more/less?

KMan
Old Jan 30, 2011, 07:32 PM
Rimmyman is offline
Find More Posts by Rimmyman
Registered User
I have mine set to the knob so i can trim it as needed.
Old Feb 06, 2011, 12:25 AM
TheRCEdge is offline
Find More Posts by TheRCEdge
Registered User
What kind of flight time are you getting out of a 2200mAh 25C
Old Feb 06, 2011, 12:35 PM
simplefly is offline
Find More Posts by simplefly
simplefly

Dynam Sr Trainer


Here is mine.
Old Feb 07, 2011, 11:16 AM
kman24 is offline
Find More Posts by kman24
Addicted To Flying Foam
kman24's Avatar
Simplefly - from your pictures it looks like the top of your rudder is a little crooked from shipping. Mine was the same way. I heated it up a bit and straightened it out the best I could. Otherwise, it looks good! Post some video when you get it up in the air

KMan
Old Feb 07, 2011, 07:53 PM
simplefly is offline
Find More Posts by simplefly
simplefly
Kman, thanks for the tip. I'll try to streighten it. I'll post videos when I get a chance.
Old Feb 08, 2011, 05:00 PM
TheRCEdge is offline
Find More Posts by TheRCEdge
Registered User
Just got mine in today. Can't wait to get it up in the air.

Scott T.
TheRCEdge.com

(Team XAircraft USA)
Old Feb 08, 2011, 08:03 PM
luvmykids2 is offline
Find More Posts by luvmykids2
Registered User
Man, my wings flex on hard turns or loops. I am going easy on this now after seeing that. Anyone snap the wings yet? They are so narrow...
Old Feb 09, 2011, 02:48 AM
TheRCEdge is offline
Find More Posts by TheRCEdge
Registered User
Im going to change out the prop and spinner what would be the best for this model...

Scott T.
TheRCEdge.com
Old Feb 09, 2011, 09:18 AM
simplefly is offline
Find More Posts by simplefly
simplefly
I'd like to do same. I wanna change the motor as well. It sounds kind of weird.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion telemaster sr ARF jrplane Electric Plane Talk 1 Nov 27, 2010 10:43 PM
Discussion Dynam Sky Trainer 4CH RTF NJRC Beginner Training Area (Aircraft-Electric) 10 Nov 18, 2010 09:45 PM
For Sale Aero Sprint Elec. ARF Trainer 50" W/S puplover Aircraft - Electric - Airplanes (FS/W) 0 Nov 15, 2010 05:15 PM
Sold Aero Sprint ARF trainer by Parma puplover Aircraft - Fuel - Airplanes (FS/W) 0 Nov 13, 2010 03:47 PM
Sold MM Special High-Wing Trainer ARF Kit AJ750 Aircraft - Electric - Airplanes (FS/W) 4 Oct 29, 2010 11:36 PM