Shop our Airplanes Products Drone Products Sales
Thread Tools
Old Dec 03, 2012, 07:15 PM
7oneWo1f is offline
Find More Posts by 7oneWo1f
AMF Years
7oneWo1f's Avatar
Regarding covering, I have figured out that humidity and temperature changes make it impossible to have perfect covering. I twice received a perfectly covered plane, once from EF, once from another brand, but by the time I got around to building it, they both developed wrinkles. Since then I've stopped complaining.

Regarding landing gear plate...never had a problem on an extreme flight plane.

Regarding landing gear on the 48" MXS...it has a weak point down by where the wheel pant mounts, if my experience is any indication. Broke mine landing half on the tarp runway, half on the grass. Broke another turning with two much speed/wiping out type of move. People are replacing these with the extra or edge landing gear. I'm just landing better. You could pre-emptively strengthing MXS (48") with kevlar thread. The 64" MXS doesn't have this issue, at least so far, in my experience.

On the 64" MXS, the only weak point I've found so far is the wheel pants. I am on my third set. I stepped on one, cracked another on a bad landing.

But there will always be some weakest link.
Sign up now
to remove ads between posts
Old Dec 03, 2012, 08:34 PM
YellowJacketsRC is offline
Find More Posts by YellowJacketsRC
They Call him Dead!
YellowJacketsRC's Avatar
rimaarts,
the LG plate is VERY VERY strong! I would not worry about it one bit. And yes, I have had problems with other planes in this area....This one is good!
Old Dec 03, 2012, 10:07 PM
Flazo is offline
Find More Posts by Flazo
JUNK RADIO
Flazo's Avatar
new pic
Old Dec 03, 2012, 11:20 PM
Liberty10 is offline
Find More Posts by Liberty10
Yin & Yang
Liberty10's Avatar
Quote:
Originally Posted by flazo View Post
new pic
Nice plane. but I couldn't help notice the fireball to the left.
Old Dec 03, 2012, 11:35 PM
Ohio AV8TOR is offline
Find More Posts by Ohio AV8TOR
On loan to Texas
Ohio AV8TOR's Avatar
Quote:
Originally Posted by Liberty10 View Post
Nice plane. but I couldn't help notice the fireball to the left.
Another Castle ESC with too much ripple current
Old Dec 04, 2012, 02:21 AM
Cabledawg1 is offline
Find More Posts by Cabledawg1
Registered User
Cabledawg1's Avatar


She is pretty....and the plane is nice too.
Old Dec 04, 2012, 05:42 AM
rimaarts is offline
Find More Posts by rimaarts
Registered User
Quote:
Originally Posted by LoneWolfRC View Post
Regarding covering, I have figured out that humidity and temperature changes make it impossible to have perfect covering. I twice received a perfectly covered plane, once from EF, once from another brand, but by the time I got around to building it, they both developed wrinkles. Since then I've stopped complaining.

Regarding landing gear plate...never had a problem on an extreme flight plane.

Regarding landing gear on the 48" MXS...it has a weak point down by where the wheel pant mounts, if my experience is any indication. Broke mine landing half on the tarp runway, half on the grass. Broke another turning with two much speed/wiping out type of move. People are replacing these with the extra or edge landing gear. I'm just landing better. You could pre-emptively strengthing MXS (48") with kevlar thread. The 64" MXS doesn't have this issue, at least so far, in my experience.

On the 64" MXS, the only weak point I've found so far is the wheel pants. I am on my third set. I stepped on one, cracked another on a bad landing.

But there will always be some weakest link.
yeah... well one thing is to get a wrinkly covering wich is understandable... other thing is to get wrinkle-free covering where on nearly any corner you can see someoene has done it on friday...

and speaking about wheel pants... on my 57" they lasted for nearly a year without any problems, but on my 51" wheelpants seemed around as strong with the same diameter wheels but lasted only 3 flights before developing cracks... on 60" aeroplanes i would like to see bigger wheelpants where we could use like 0.5" bigger aftermarket wheels... (like on 42" slick i can easily run 2.5 dubro wheels requiring only a bit of dremel job and still looking quite decent...)

i hinged everything, glued elevator yesterday... i think i will be able to get 60-70* easily on elevator.... on my mxs im running 55 and find it plenty!

either something is wrong with my new and fresh ca bottle, either something was off with hinges, but ca did not seem to wich in momentarily...im not worried about aelerons, but more about elevator! i blendermed it, but still im thinking about going with epoxy hinges...
Old Dec 04, 2012, 09:22 AM
Flazo is offline
Find More Posts by Flazo
JUNK RADIO
Flazo's Avatar

anything


Quote:
Originally Posted by Liberty10 View Post
Nice plane. but I couldn't help notice the fireball to the left.
Keeping warm like the Homeless...



fred
Old Dec 04, 2012, 10:21 AM
Aeroplayin is offline
Find More Posts by Aeroplayin
Registered User
Aeroplayin's Avatar
Quote:
Originally Posted by Cabledawg1 View Post


She is pretty....and the plane is nice too.
It's amazing now calling him, a she, resulted in a quick 61 views. I'm guessing from my past experience with the area, the sun was going down already around 4 PM and the fireball is actually a car's headlights.
Old Dec 04, 2012, 10:29 AM
Liberty10 is offline
Find More Posts by Liberty10
Yin & Yang
Liberty10's Avatar
Quote:
Originally Posted by Aeroplayin View Post
It's amazing now calling him, a she, resulted in a quick 61 views. I'm guessing from my past experience with the area, the sun was going down already around 4 PM and the fireball is actually a car's headlights.
I'm pretty sure it's a fire in a barrel. It does look like someone either recently stoked it or tossed on some accelerant. I stood around many a fire barrel on construction sites back in the day. Amazing how well a large tube of glue will start wet wood on fire
Old Dec 04, 2012, 02:13 PM
rimaarts is offline
Find More Posts by rimaarts
Registered User
just adding to battery discussion... 3600 hayin 30c - weighter 1 out of 3 and it was 608g... just for comparison i will try getting gens ace 3700 (when i can finally source them)
Old Dec 04, 2012, 03:35 PM
Aeroplayin is offline
Find More Posts by Aeroplayin
Registered User
Aeroplayin's Avatar
My Gens Ace 6S 3300mAh 25C is 525.78 g (18.56 oz) and my 6S 3300mAh 30C Sky is 507.65 g (17.92 oz). Both with Velcro.
Old Dec 06, 2012, 09:42 AM
Wingbreaker is offline
Find More Posts by Wingbreaker
Video Juggernaut
Wingbreaker's Avatar
I just picked up one of these locally from a fellow forum member for a really great deal, looks like new. It was built very well. Anyone ever try the exceed rocket motors on this plane? I have a motrolfly on my slick. I like it but wanted to try to go economical this time around if possible.
Old Dec 06, 2012, 10:08 AM
Aeroplayin is offline
Find More Posts by Aeroplayin
Registered User
Aeroplayin's Avatar
There was a guy on the 60/64 MXS thread that not only had one in his plane but also posted a video. It's worth a thousand words. He had a Rocket 4120-465 with an 85A ESC. Don't remember what prop, but I would PM him and find out how the motor held up. It was on the original MXS thread and it was not early in the thread. It may be easier to find by going to youtube and searching for it....

Okay, I just did that and here it is... and it was a 16x8 prop.

ExtremeFlightRC 64'' MXS-R_Maiden (3 min 49 sec)
Old Dec 06, 2012, 10:32 AM
7oneWo1f is offline
Find More Posts by 7oneWo1f
AMF Years
7oneWo1f's Avatar
I have used a few rocket series motors, and haven't had any problems with them...up to a 48" EPP foam plane. I did have to reverse the shaft on the smaller motors for my application on one of my planes. Wasn't hard, and worked out very well.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product Extreme Flight 48" Edge 540T EXP! hemituda 3D Flying 12588 Nov 23, 2016 03:08 PM
Wanted Extreme Flight 48" Edge 540T EXP FD Pilot Aircraft - Electric - Airplanes (FS/W) 7 Jul 02, 2010 12:52 PM
Discussion Daniel Holman puts the new Extreme Flight EDGE 540T EXP through the wringer! EXTREME FLIGHT 3D Flying 21 May 30, 2010 02:17 AM
Discussion 42" AJ Slick or 48" Extreme Flight Edge 540T-EXP LeeJ 3D Flying 13 Mar 26, 2010 09:26 PM