HeadPlay Goggle Mods for FPV - Please Advise - Page 3 - RC Groups
Thread Tools
Nov 21, 2010, 12:17 PM
'FPV'er...not a "LOS'er
Vantasstic's Avatar
Another mounting possibility. Use a skate board helmet like in this post: https://www.rcgroups.com/forums/show...1&postcount=13 . Mount the liberator in the top of the helmet like in this post: https://www.rcgroups.com/forums/show...7&postcount=14 then mount a flip up visor painted black for light blocking: http://www.harborfreight.com/face-sh...sor-96542.html . This might provide the best of all worlds...an all-in-one unit, lighter and cooler on the head, and a flip up visor for light blocking, and can be assembled for ~$30-$40 dollars. That would give me a a total cost of ~$150 ($108 for the HP on sale and <$40 for the helmet and light blocking visor.
Sign up now
to remove ads between posts
Nov 21, 2010, 01:00 PM
Robot, RC Pilot & Builder :-)
kevinhines's Avatar
Quote:
Originally Posted by Art Newland
I bought the connector mentioned in post #8, fits fine. I have a couple of older Thunderpower 2000ish 3s lipos that still charge and balance OK, but power is down under load, so I'll use these to power my Headplays. I just tapped into the balance plug. I hope to find a project box of some lind to mount the liberator to, to hold the battery.
Hi Art,

Thanks! I'm glad to hear the Radio Shack power plugs are working for you... I just picked up a couple of these.

That's a cool idea to tap into the Lipo's balance plug, to power the HP...

What concerns or issues are there tapping into the Lipo's balance plug, vs. using the Deans connector, and how do you avoid this issues? ... for example, risk of reverse voltage polarization, risk of unplugging from the balance plug during a flight, etc...?

Thanks,
Kevin
Nov 21, 2010, 01:19 PM
Robot, RC Pilot & Builder :-)
kevinhines's Avatar
Quote:
Originally Posted by Art Newland
The way I understand it, using the 18r firmware stops the low frame rate problem. I installed the 18r (came with 20r installed) and played with them, even totally removing video signal, display came back immediately when reconnected.
Art,

Thanks! That's a good experiment... you are providing helpful info... that's good to know the signal will come back quickly.

Thanks!

Kevin
Nov 21, 2010, 01:26 PM
Robot, RC Pilot & Builder :-)
kevinhines's Avatar
Quote:
Originally Posted by Vantasstic
...
For the HP, that darn Liberator is not very liberating. I read of using a belt clip and such to keep it from cable/plug damage...
Hi Van, Thanks!

Cool info... would you happen to have a link to the belt clip info? ...especially with pictures?


Quote:
Originally Posted by Vantasstic
Another mounting possibility. Use a skate board helmet like in this post: https://www.rcgroups.com/forums/show...1&postcount=13 . Mount the liberator in the top of the helmet like in this post: https://www.rcgroups.com/forums/show...7&postcount=14 then mount a flip up visor painted black for light blocking: http://www.harborfreight.com/face-sh...sor-96542.html . This might provide the best of all worlds...an all-in-one unit, lighter and cooler on the head, and a flip up visor for light blocking...
Thanks for sharing this info... the bike/skating helmet looks a lot more comfortable than the motorcycle helmet...

While I plan to go with a belt clip... I certainly appreciate the thought you are putting into your helmet mount...

Thanks for shaing this great information!

Kevin
Nov 21, 2010, 01:29 PM
Registered User
Here's some HP mods I've done.

Pic 1: Side light blocking velcro with Flytron headtracker and video Rx antenna mounted next to it.

Pic 2: Front view.

Pic 3: Bottom light blocking velcro strips with one removed.

Pic 4: Liberator with video reciever velcro'd into battery compartment. Hot glue used to secure A/V DIN plug and goggles/liberator connector.

Pic 5: Liberator with belt loop made out of wide velcro. I velcro an 1800mAH 3S lipo to this side, to power goggles and video Rx for a few hours.
Nov 21, 2010, 01:39 PM
Robot, RC Pilot & Builder :-)
kevinhines's Avatar
Quote:
Originally Posted by patricklupo
Here's some HP mods I've done.

Pic 1: Side light blocking velcro with Flytron headtracker and video Rx antenna mounted next to it.

Pic 2: Front view.

Pic 3: Bottom light blocking velcro strips with one removed.

Pic 4: Liberator with video reciever velcro'd into battery compartment. Hot glue used to secure A/V DIN plug and goggles/liberator connector.

Pic 5: Liberator with belt loop made out of wide velcro. I velcro an 1800mAH 3S lipo to this side, to power goggles and video Rx for a few hours.
Patrick,

WOW! AWESOME mods!

I'm going to study your work for a bit, before I post questions... there are so many great mods in your photos... this is exactly the sort of info I'm seeking...

Thanks!!!

Kevin
Nov 21, 2010, 01:43 PM
'FPV'er...not a "LOS'er
Vantasstic's Avatar
Quote:
Originally Posted by kevinhines
... would you happen to have a link to the belt clip info? ...especially with pictures?
Nope, I've read about it, but never seen a picture (except what patricklupo just posted). I'm still milling over ideas. Patricks setup looks pretty good really. I don't have a head tracker and mounting my VRx to the liberator wouldn't work for me (using large 900mHz patch antenna)...but the velcro'd battery/belt strap and light blockers has their merits. As I think about it, it'd probably be better to start simple/cheap before dropping more cash on a helmet type setup. Good stuff going on here.
Nov 21, 2010, 02:27 PM
KISS
hefest's Avatar
@kevinhines

if you could update first post with the potentially useful answers for each of the questions would be great.

Thanks
Nov 21, 2010, 02:42 PM
My Karma ran over my Dogma
fireslayer26's Avatar
Quote:
Originally Posted by patricklupo
Here's some HP mods I've done.

Pic 1: Side light blocking velcro with Flytron headtracker and video Rx antenna mounted next to it.

Pic 2: Front view.

Pic 3: Bottom light blocking velcro strips with one removed.

Pic 4: Liberator with video reciever velcro'd into battery compartment. Hot glue used to secure A/V DIN plug and goggles/liberator connector.

Pic 5: Liberator with belt loop made out of wide velcro. I velcro an 1800mAH 3S lipo to this side, to power goggles and video Rx for a few hours.
Nice job patricklupo!
Nov 22, 2010, 12:14 AM
CD-ROM Junkie
Art Newland's Avatar
Quote:
Originally Posted by kevinhines
Hi Art,

Thanks! I'm glad to hear the Radio Shack power plugs are working for you... I just picked up a couple of these.

That's a cool idea to tap into the Lipo's balance plug, to power the HP...

What concerns or issues are there tapping into the Lipo's balance plug, vs. using the Deans connector, and how do you avoid this issues? ... for example, risk of reverse voltage polarization, risk of unplugging from the balance plug during a flight, etc...?

Thanks,
Kevin
I have about an hours worth of watching video on my Headplays, looks like I should be able to get a couple hours of use on a 2000. The balance plugs on the Thunderpowers have a clip that snaps them in place and has to be squeezed to be released. I think the wiring is plenty large enough to handle the HP's .4 amps. The balance plugs are polarized, make sure you have the polarity correct when you solder it up, I checked the four batteries I have with Thunderpower balance plugs... they were all the same. YMMV
Nov 22, 2010, 02:46 AM
Registered User
The only difficult mod was cutting the bottom light blocking strips properly. For that you need to use some sort of putty or even a piece of wire that can take an impression of the curve of your face, just under your eyes. That way you can accurately cut the outline of the velcro to match the curve of your face, to block out light effectively.

Even then, the edge of the velcro strips felt a bit sharp on my face, so I took a butane lighter to the velcro edges to soften them up a bit. Light from the top and sides are completely blocked, while about %90 from the bottom is. I think if I found a bit of T shaped rubber to attach to the bottom strips it would be 100%, but as is, it's pretty good in direct sunlight.

The best source material I found is to get a 15ft x 2" Velcro brand roll; got mine from OSH hardware.
Nov 22, 2010, 04:48 AM
Registered Abuser
ziomatrixacs's Avatar
Quote:
Originally Posted by Vantasstic
Another mounting possibility. Use a skate board helmet like in this post: https://www.rcgroups.com/forums/show...1&postcount=13 . Mount the liberator in the top of the helmet like in this post: https://www.rcgroups.com/forums/show...7&postcount=14 then mount a flip up visor painted black for light blocking: http://www.harborfreight.com/face-sh...sor-96542.html . This might provide the best of all worlds...an all-in-one unit, lighter and cooler on the head, and a flip up visor for light blocking, and can be assembled for ~$30-$40 dollars. That would give me a a total cost of ~$150 ($108 for the HP on sale and <$40 for the helmet and light blocking visor.


I use face shields like that at work, they are real annoying to flip up. Especially the ones without the head harness. I like the helmet rigs because they are so practical but I cant get over looking like a crazy tin foil hat man in the middle of a corn field.

Has anyone put a quality 2.4 or 5.8ghz receiver in the liberator to get a signal from a dedicated GS? I mean, having your video sent from the air to the ground then over air to your head set will reduce the quality some but its a thought.
Nov 22, 2010, 05:20 PM
Registered User
DayDream's Avatar
this mod is now obsolete
https://www.rcgroups.com/forums/show....php?t=1401970

My mod to power the HP with a 3S lipo.

I tapped right to the board, this may void you warranty


1)Five screws hold the battery tray and everything else together, middle screw
is under the white seal.

2)It will all come apart at this point so don't lose any parts, and mind the
thermal grease.

3)Locate the power plug connections. (the two at the very back of the
connector.)

4)Use your expert soldering skills to connect red on the card slot side, and
the black on the battery pins side.

5)Using tin snips cut the square hole for the battery pins about 3mm longer
on the aluminum plate and bend it up to make room for your wires to go by.

6)At this point before you screw it together you going to want to check your
work by plugging in the a/c adapter, use a multimeter to check the voltage
and polarity 12.10v, red+, black- you know...

(WARNING: do not power up the board without it put together with the heat sink.)
Last edited by DayDream; Apr 13, 2011 at 06:19 PM.
Nov 22, 2010, 07:43 PM
KB3VOJ
cherokee180c's Avatar
Or just integrate into your GS like this:

https://www.rcgroups.com/forums/show...&postcount=220

Low voltage alarm now for everything including HP goggles. Power and Video/Audio from a single Ethernet Cable. Nice and neat.
Nov 22, 2010, 07:55 PM
Registered User
cliffkot's Avatar

MP4 File Problems


According to the specifications, the HeadPlay goggles are supposed to play MP4 files. My goggles see the files, but will not play them. I get a "load error" prompt.

The HeadPlay support people said the problem was that I was trying to use the USB port and that I should get the compact flash card because it was faster. I tried that with the same result.

I think I might be getting the runaround. Any suggestions gentlemen?

Cliff K.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Headplay New software for FPV Talajouy FPV Talk 35 Feb 05, 2011 02:26 AM
Build Log Headplay mods ashdec87 FPV Talk 30 Dec 27, 2010 12:03 PM
Discussion Four reason not to buy a Headplay goggle for FPV Talajouy FPV Talk 26 Nov 14, 2010 11:08 PM
Discussion 8 Reasons for not to Buy a Headplay for FPV gogi FPV Talk 84 Apr 16, 2010 11:47 PM
Discussion Headplay Video Goggle Question shmo70 FPV Talk 21 Nov 19, 2009 10:21 AM