Shop our Airplanes Products Drone Products Sales
Thread Tools
Dec 17, 2010, 12:48 AM
I'd rather be flying!
turboparker's Avatar
Got mine from RC the other day. I plan to install it in my mSR this weekend. Looking forward to my turbo-mSR.

Joel
Sign up now
to remove ads between posts
Dec 17, 2010, 01:27 AM
HELP I AM BEING SET UP!!
maukabud's Avatar
Quote:
Originally Posted by turboparker
Got mine from RC the other day. I plan to install it in my mSR this weekend. Looking forward to my turbo-mSR.

Joel
Just one? *gasp!*

I'm sure you have other micros that would benefit....



Bud, pushes SP motors like crack Bud
Dec 17, 2010, 01:27 AM
Flash, AAAAAAAAAAAHhhhhhhhhh
flashkick's Avatar
haha i ordered like 3 or 4 and i only have one plane that can use it. haha
Dec 17, 2010, 07:33 AM
Registered User
Quote:
Originally Posted by Brent Slensker
SAVE your pinion gears!
I have "just a few" ...but under a magnifying glass noticed that some are (prudently) not usable - surprisingly, the teeth show a lot of wear. Those were on the best performing motors I had - obviously. Too bad they didn't all last that long!

Would be great if there was a new pinion source -- like BSD (who does have 10-teeth pinions).

Gene K
Dec 17, 2010, 10:43 AM
QuAd FaNaTiC
Razors edge 29's Avatar
"I said god damn, god damn bud the pusher man"

Loo



Quote:
Originally Posted by maukabud
Just one? *gasp!*

I'm sure you have other micros that would benefit....



Bud, pushes SP motors like crack Bud
Dec 17, 2010, 11:30 AM
**I'm Battman**
RCBABBEL's Avatar

GWS Micro Gear Puller:


It's really starting to let me down.

The small soft brass SP pinion is sliding through the base slot.
That slot is just a little over sized for the SP stock pinion gear.

Any experience out there with the Walkera Silver GP?
http://www.dealextreme.com/details.dx/sku.15147

rc
Dec 17, 2010, 11:56 AM
Heli collector
livonia bob's Avatar
Quote:
Originally Posted by RCBABBEL
It's really starting to let me down.

The small soft brass SP pinion is sliding through the base slot.
That slot is just a little over sized for the SP stock pinion gear.

Any experience out there with the Walkera Silver GP?
http://www.dealextreme.com/details.dx/sku.15147

rc
I have both and for what you are doing the Walkera one will work better.. Funny that for working on Walkera motors the GW/GP-MICRO works better..
Dec 17, 2010, 12:18 PM
**I'm Battman**
RCBABBEL's Avatar
Quote:
Originally Posted by livonia bob
I have both and for what you are doing the Walkera one will work better.. Funny that for working on Walkera motors the GW/GP-MICRO works better..
Thanks lb,

I'll get one ordered.

As for now, MacGyver to the rescue.

Old saw blade with a dremel cutoff wheel slot cut into it.


If the pinion sits too close to the motor can this sweet needle nose plier pictured in pic#1 will easily slide the pinion to the top of the motor shaft.
http://www.homedepot.com/webapp/wcs/...01&marketID=76

rc
Dec 17, 2010, 12:37 PM
QuAd FaNaTiC
Razors edge 29's Avatar
mine doesn't do that.




QUOTE=RCBABBEL;16848821]It's really starting to let me down.

The small soft brass SP pinion is sliding through the base slot.
That slot is just a little over sized for the SP stock pinion gear.

Any experience out there with the Walkera Silver GP?
http://www.dealextreme.com/details.dx/sku.15147

rc[/QUOTE]
Dec 17, 2010, 01:11 PM
**I'm Battman**
RCBABBEL's Avatar
Quote:
Originally Posted by Razors edge 29
mine doesn't do that.




QUOTE=RCBABBEL;16848821]It's really starting to let me down.

The small soft brass SP pinion is sliding through the base slot.
That slot is just a little over sized for the SP stock pinion gear.

Any experience out there with the Walkera Silver GP?
http://www.dealextreme.com/details.dx/sku.15147

rc
[/QUOTE]



Re,

My GWS puller was great for about the first 30 motors.

Did your motor show up yet?

rc
Dec 17, 2010, 01:18 PM
QuAd FaNaTiC
Razors edge 29's Avatar
no not yet

anxiously awaiting

I think i might outfit it to my MSR for now

to try it at least as its all the rag on those threads

Or i might add it to a scratch built




Re,

My GWS puller was great for about the first 30 motors.

Did your motor show up yet?

rc[/QUOTE]
Dec 17, 2010, 06:17 PM
I'd rather be flying!
turboparker's Avatar
Quote:
Originally Posted by maukabud
Just one? *gasp!*

I'm sure you have other micros that would benefit....

Bud, pushes SP motors like crack Bud
Bud,

Just one...for now. I had a new P-51 motor just sitting around, so I put it in my Champ. XP #2 & 3, are still going strong on their original motors, and my V2 w/P-51 motor is still going. When they start to fade, I will definitely go with the SP motors (if I don't go b/l).

I am reminded of GNR's Mr Brownstone: "I used ta do a little but a little wouldn't do it so the little got more and more."

Anyone have any RPM comparison data on the SP & XP motors?

Joel
Dec 18, 2010, 08:13 PM
They took the bar
javelina's Avatar
what's the shaft OD for the SP motor? Still awaiting delivery of mine....

Just wanting to see if we can find replacement pinions, (9T).


wish it was this simple:

http://www3.towerhobbies.com/cgi-bin...&I=LXVY75&P=FR
Dec 18, 2010, 08:40 PM
**I'm Battman**
RCBABBEL's Avatar
Quote:
Originally Posted by javelina
what's the shaft OD for the SP motor? Still awaiting delivery of mine....

Just wanting to see if we can find replacement pinions, (9T).


wish it was this simple:

http://www3.towerhobbies.com/cgi-bin...&I=LXVY75&P=FR
Jav,

SP motor shaft measures 0.97~.098mm

Tower 9T pinion:
Shaft hole diameter: 2.5mm


I'm looking into pinion sources like this:
http://www.shop.kkpmo.com/index.php/...5d7fbd8154a565



rc
Dec 18, 2010, 08:47 PM
QuAd FaNaTiC
Razors edge 29's Avatar
please advise if ya have any luck babs.


Quote:
Originally Posted by RCBABBEL
Jav,

SP motor shaft measures 0.97~.098mm

Tower 9T pinion:
Shaft hole diameter: 2.5mm


I'm looking into pinion sources like this:
http://www.shop.kkpmo.com/index.php/...5d7fbd8154a565



rc


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Blade MSR or Nine eagles solo Pro jtravel Coaxial Helicopters 2 Oct 18, 2010 06:45 AM
For Sale Nine Eagles Solo Pro II V5 Deluxe Kit (Price update) iflabs Aircraft - Electric - Helis (FS/W) 2 Oct 10, 2010 05:13 PM
Wanted Nine (9) Eagles Solo Pro - 'copter only. emarkay Aircraft - Electric - Helis (FS/W) 3 Oct 07, 2010 11:00 AM
Discussion Revell Proto MAX RTF/Nine Eagles Solo Pro RTF $69.99 at Tower Hobbies Firehawk989 Hot Online Deals 1 Sep 29, 2010 12:16 AM
Wanted Nine Eagles Solo pro radio flyerjs Aircraft - General - Radio Equipment (FS/W) 0 Sep 20, 2010 04:10 PM