Jakub Frame Thread - Page 55 - RC Groups
Shop our Airplanes Products Drone Products Sales
Thread Tools
Sep 06, 2011, 03:26 PM
AMA 46133
Originally Posted by topgearuk
Thanks for that information, I've gone with jakub's recommendation. I'll see how that flys for now.
Ive ordered a kk board until I can lay my hands on a cc one!
I see that Jakub recommends motors in the similar range.

KK is good. I am testing one in my Jakub's quad now. CC is also good when you can get your hands on one.
Sign up now
to remove ads between posts
Sep 08, 2011, 04:52 PM
Registered User
2 Quads and a Hexa (6 min 9 sec)
Sep 11, 2011, 07:59 PM
Registered User


I finished my LL4 last week and strapped the GoPro on it this weekend. Here's my first MultiRotor video:

QuadCopter around the house (2 min 10 sec)
Last edited by MaxGen; Sep 13, 2011 at 09:57 PM.
Sep 12, 2011, 12:40 AM
Registered User

fpv doubt :)

little off from the topic .. im very new to fpy , so i just added 1.2g vtx with gopro to my multicopter LL4, the video quality was good till the motors are not armed , at the time when copter is armed i get very bad distortions in the video , what might be the problem , please advice
Sep 12, 2011, 12:51 AM
Registered User
Grey lines accross the screen?

You need to filter the power used for the video gear. Make your own, search for: sander style LC filter
Sep 12, 2011, 12:51 AM
Registered User
This post:
Sep 12, 2011, 04:14 AM
Registered User
Thanks a lot Jaguar_5, i will try this immediately
Sep 12, 2011, 03:57 PM
Registered User

Fiberglass "crow" frame is pretty crash proof

Last weekend I had some unfortunate mailfunction during flight, which ended in an approx 200m free fall. I used Jakub's fiberglass frame, and was impressed how crash proof is it. Despite the long way down, I have to replace only one arm, all other components are survived (well except the props and the bearings). It seems that the clever composition of the arm acted as a shock supressor.
See it in video :
Quadcopter Major crash (1 min 22 sec)

I already ordered the spares. (plus black crow frame just because it's soo cooool).
Sep 13, 2011, 01:54 AM
Jakub J's Avatar
Originally Posted by eosbandi
Last weekend I had some unfortunate mailfunction during flight, which ended in an approx 200m free fall....
Nice landing
You're right - this frame almost always will break in the same place -
main part with controller is safe

Sep 17, 2011, 11:25 PM
aka Helidaho
AeroVideoUS's Avatar
Finally finished my Lunar Lander 4 frame with 2 axis gimbal. Here is the first test flight. Not bad, but I think I can tweak some of the gimbal roll and tilt parameters on my Hoverfly Pro board to get it a little better but thought this was a pretty good first flight test.

My only problem now is the motors are in the line of view of the GoPro, which was fine for testing the gimbal to see the movement but not good when I want to shoot good video.

I don't suppose you have a tabbed center piece to push the gimbal our further? Maybe some thicker center plates with a tab coming off the front of one of them?

This is a great frame and flew well, can't wait to take it out for some FPV flights.


Lunar Lander 4 Frame Gimbal Test with Hoverfly Pro (3 min 56 sec)
Sep 18, 2011, 05:02 AM
Registered User
Pretty much ready to buy the camera mount (the black looks much cooler )...

Are these the es08md servos but with a different name?


They're digital... that correct? I'll be using them with the multiwii software.

And how much difference do the bearing upgrades make? And side by side comparison videos?

Sep 18, 2011, 05:11 AM
Jakub J's Avatar

I have just bought Emax servos here:

All were ok.

Sep 21, 2011, 03:51 AM
Registered User
First post in this thread...

I have just completed the Tricopter with the quadframe.com MultiWii-controller, and I was really impressed by the quality! My girlfriend thinks the Tricopter looks like an ugly tv-antenna, but I think it looks cool! High Tech!

My first few flights (ever with a multicopter) where not that successful, I must have broken about 5 props already. I thought I could manage without propsavers, but I was wrong! I have also broken 3 servo arms. Propsavers are strongly recommended!

I have now upgraded the MultiWii firmware to 1.8, and I find it much more stable! I wish I had done this before the first flight. The weird thing though, is the accelerometer differences between the two versions. In 1.7, the Acc parameters where Roll: 0, Pitch: 0, Z: 255. In 1.8, they are Roll: 0, Pitch 0, Z: 507. Strange! Has anyone got an explanation for this? Does it even matter?

The stable mode is now trimmed in, but I had to use a lot of stick-trimming to make the tricopter fly level in stable mode. About 30 roll "clicks" to the left and 15 negative pitch clicks. And I thought calibrating it in the config GUI was enough?

Finally, some thougts about the RCTimer parts I bought:

RCTimer 18A ESCs: Seems to work ok, but they constantly emit a high pitch beeeeeeeeeeep. They might not like the high update rate?

RCTimer 750kv motors: I ordered four of these, just to have one spare. It turned out to be a good idea, as one of them vibrated heavily right from the start. I believe the bearing needs to be changed. Turning the motor by hand reveals an "not so smooth" section about 20 degrees wide.
Having flown (and landed upside down) a few times has made the shafts come loose. But that might be because I didn't use propsavers.

12 pairs of counter rotating props: Needs a lot of balancing. I tried to balance the first one by sanding it at the heavy side. It got thinner and thinner, and was still not balanced. I abandoned that solution and used CA to make the light side heavier. That worked, but I believe it makes the prop more brittle.

If you can find your parts anywhere else...don't use RCTimer.
Sep 22, 2011, 07:50 AM
My other vehicle is unmanned
fpvnick's Avatar
i use a bit of electrical tape on my light blade to balance props just stick it onto the front edge and keep trimming it until it balances you can move the bit of tape from along the blade to get it perfect then wrap the tape down both top and bottom done. it can also be taken off and rebalanced if your not happy with it i think this is much better than ca.

Paul nice vid seems to work well for a first attempt it kind of cool seeing the motors move in the image but as you say from a more professional video point of view it would be better to have them out of view.

I got my cam gimbal together and tested im using the hitech servos and it seems to work great no slop or play at all i would recommend getting the ball race extras if your buying a new kit. i just need to mount it on my xquad and get it working with the board tonight. i cant wait to try flying with it.
Last edited by fpvnick; Sep 22, 2011 at 08:07 AM.
Sep 22, 2011, 11:46 AM
Registered User
Mortimer's Avatar
Originally Posted by Jakub J
Advanced MultiWii FPV flying controller is on stock!
That was two weeks ago.
Now it' written "Cart Error - The product 'MultiWii FPV flying controller - MultiWii FPV controller QUADcopter X firmware' is already sold out."

When is the new batch expected ?

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Sold RTF 330x w/Termniator AP/AV (pan and tilt) frame and original frame RTF!!! wac Aircraft - Electric - Helis (FS/W) 18 Oct 01, 2010 11:08 AM
Heliup.com CNC CF Shogun/Zoom frame build thread/review Hoverup Mini Helis 123 Jun 18, 2005 10:09 PM
Trex Mh upgrades build thread+New CF frame review Philpops Mini Helis 127 May 29, 2005 07:04 AM
Trex Mh upgrades build thread+New CF frame review Philpops Mini Helis 77 May 23, 2005 11:40 PM