Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Aug 03, 2011, 12:39 PM
JimDrew is offline
Find More Posts by JimDrew
Xtreme Power Systems
Quote:
Originally Posted by EDF Crazy View Post
Jim and anyone else, iv moved over to the A123 packs and im wondering how you connect them to the receiver,
there are 3 leads,
1. deans plug,
2. balance plug and
3. a small lied with a servo connector on the end.

I know some of you are using switches and some arent, im not keen to use a switch, do you guys just get one of these and put it directly into your receiver?
I use a plug similar to your first picture... just a Deans Ultra male connector to a JST servo connector. The servo connector stays in the receiver (is actually shoo-goo'd along with the rest of the servo plugs in the receiver). You just plug the Deans connector from the A123 to the harness as your "switch".
RCG Plus Member
Sign up now
to remove ads between posts
Old Aug 03, 2011, 12:43 PM
JimDrew is offline
Find More Posts by JimDrew
Xtreme Power Systems
OK, I put two flights on the Habu today.. holy frick'n nose heavy! I had CG at 107mm, and it needed 1/8" of up trim to flight flat. Got the flaps worked out but opted to land without them on the first landing. No brainer.. Second flight I moved CG to 115mm and it still needed at least 1/16" of up trim. Even with this trim, a perfect flat/level pass (starting at 50' AGL) to 10' was exactly 130MPH on the radar gun. Not bad for a 100% stock setup with no nose gear door (just the funky cutout thing) and the stock partial main gear doors.

Flys like it is on rails. This is actually a really good plane for practicing speed runs. It's tiny, so really far away it resembles how far you have to go with the speed planes to start your run. I like it.
RCG Plus Member
Last edited by JimDrew; Aug 03, 2011 at 01:12 PM.
Old Aug 03, 2011, 12:48 PM
GuppyG is offline
Find More Posts by GuppyG
Registered User
Quote:
Originally Posted by JimDrew View Post
OK, I put two flights on the Habu today.. holy frick'n nose heavy! I had CG at 107mm, and it needed 1/8" of up trim to flight flat. Got the flaps worked out but opted to land without them on the first landing. No brainer.. Second flight I moved CG to 100mm and it still needed at least 1/16" of up trim. Even with this trim, a perfect flat/level pass (starting at 50' AGL) to 10' was exactly 130MPH on the radar gun. Not bad for a 100% stock setup with no nose gear door (just the funky cutout thing) and the stock partial main gear doors.

Flys like it is on rails. This is actually a really good plane for practicing speed runs. It's tiny, so really far away it resembles how far you have to go with the speed planes to start your run. I like it.
It looks like your second CG was a typo. If it was what CG did you end up at for the 1/16th of up trim?

Thanks,
scott.
Old Aug 03, 2011, 01:11 PM
JimDrew is offline
Find More Posts by JimDrew
Xtreme Power Systems
ACK! Yes, corrected!! 115mm is still too nose heavy. That needs 1/16th up trim. I am measing from the leading edge of the wing root at the fuse to the center of the fuse/wing, using calipers. So, I believe that is pretty accurate. I think it will end up quite aways back in order to be able to fly nearly hands off while inverted. It will also pick up a bunch of speed too by moving the CG back - not to mention getting rid of the trim which is scrubbing off quite a bit of speed.
RCG Plus Member
Old Aug 03, 2011, 01:22 PM
tulz43 is offline
Find More Posts by tulz43
Registered User
tulz43's Avatar
HAHA I was gonna say... that would have been super nose heavy. Glad you like it Jim. They do fly great. I'd say I'm close to 120mm back.
Old Aug 03, 2011, 04:54 PM
JimDrew is offline
Find More Posts by JimDrew
Xtreme Power Systems
That makes sense. I figure I will end up just a bit tail heavy (how I like all of my aircraft) so it flies neutral upright and inverted. I do like the way it tracks.
RCG Plus Member
Old Aug 03, 2011, 08:52 PM
RickyBoy49 is offline
Find More Posts by RickyBoy49
RickyBoy
Hey Tam received my nose strut for my BVM Electra.....all ready to go Maiden this weekend. Thanks again Rick
RCG Plus Member
Old Aug 03, 2011, 09:20 PM
danamania is offline
Find More Posts by danamania
Advocating for RC Aviation
Jim, all, thanks for sharing the CG data. Will be helpful later in my build. Just got started tonight and the aileron servos are done. Habu-32, Nice

Tam, thanks for the fan. The TJ80 arrived today. It's awesome looking! I won't get to install it for a few days or a week or so. Meanwhile, is the Ice programmed? No worries, I can do. Anyone who would care to share their ESC settings, thanks in advance (my first inrunner). Good flying! Dana
Old Aug 03, 2011, 09:43 PM
cableguy351 is offline
Find More Posts by cableguy351
Registered User
Tams fans are all set up to just hook up and fly
Old Aug 03, 2011, 10:13 PM
ZACATTACK is offline
Find More Posts by ZACATTACK
Registered User
ZACATTACK's Avatar
Quote:
Originally Posted by danamania View Post
Jim, all, thanks for sharing the CG data. Will be helpful later in my build. Just got started tonight and the aileron servos are done. Habu-32, Nice

Tam, thanks for the fan. The TJ80 arrived today. It's awesome looking! I won't get to install it for a few days or a week or so. Meanwhile, is the Ice programmed? No worries, I can do. Anyone who would care to share their ESC settings, thanks in advance (my first inrunner). Good flying! Dana
Dont touch the settings is what Tam told me..Plug in and Fly..If you have a problem..send it back to him.. That's the response I got Dana!! If you need to know my settings PMME..I'll scan&send the CC Data sheet with my 1409/2Y settings... Your gonna like it Dude!!
Old Aug 04, 2011, 01:00 AM
mickydee is online now
Find More Posts by mickydee
Registered User
Hi EDF Crazy,

Where did you find those adapters for A123 reciever packs?

Thanks! Mickydee
Old Aug 04, 2011, 02:24 AM
tulz43 is offline
Find More Posts by tulz43
Registered User
tulz43's Avatar
For the guys running the stock setup with castle ice 100. What are you esc settings?
Old Aug 04, 2011, 04:38 AM
EDF Crazy is offline
Find More Posts by EDF Crazy
Registered User
EDF Crazy's Avatar
Quote:
Originally Posted by mickydee View Post
Hi EDF Crazy,

Where did you find those adapters for A123 reciever packs?

Thanks! Mickydee
I found it on this website towards the bottom of the page. Its a uk based site, im sure someone will sell these in the USA

http://www.electricwingman.com/lithi...ter-cable.aspx
Old Aug 04, 2011, 08:33 AM
Madmax1965 is offline
Find More Posts by Madmax1965
Watt me worry?
Madmax1965's Avatar
Thanks for the link EDF...............I think I saw them on a U.S. site somewhere. I usually solder a connector on the A-123 packs but this adapter would make life easier.
Old Aug 04, 2011, 12:16 PM
Tamjets is offline
Find More Posts by Tamjets
Registered User
Tamjets's Avatar
Quote:
Originally Posted by danamania View Post
Jim, all, thanks for sharing the CG data. Will be helpful later in my build. Just got started tonight and the aileron servos are done. Habu-32, Nice

Tam, thanks for the fan. The TJ80 arrived today. It's awesome looking! I won't get to install it for a few days or a week or so. Meanwhile, is the Ice programmed? No worries, I can do. Anyone who would care to share their ESC settings, thanks in advance (my first inrunner). Good flying! Dana
Your set up is 1509 3D.
I had set up low timing and 8pwk for effecient.
You can take a peak and save it. But don't chance anything.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Fiberglass Habu Airframe Calvin_220 Electric Ducted Fan Jet Talk 92 Nov 10, 2012 03:53 AM
Sold New in box Habu EDF PNP flyboy1945 Aircraft - Electric - Jets (FS/W) 2 Aug 01, 2010 09:24 PM
Discussion ESC very HOT - Sorry the discussion is moved to the Habu thread SalamSyed Foamy EDFs 0 Mar 21, 2010 12:15 AM
New Product New Fiberglass EDF Jets!!! Starfire + EDF Trainer nitroplanes Nitro Planes 0 Jan 24, 2009 10:58 AM
Discussion Baja SS Speculation and hopup thread. DaveESPI Large Scale Cars 3 Feb 03, 2008 08:39 PM