Thread Tools
Old Aug 10, 2011, 04:53 PM
wishawhunk is offline
Find More Posts by wishawhunk
Thanks Bowerz. I have flown a parkzone stryker and had it modded to the max. Guess this will be similar! I will also do the mods to this after a while. Anyone used the styker motor mount out of interest?
Sign up now
to remove ads between posts
Old Aug 10, 2011, 05:09 PM
Bowerz is offline
Find More Posts by Bowerz
Once crash at a time
Bowerz's Avatar
i suggest doing what these guys do in the second part of their video.

Flite Test - EPO ParkJet - REVIEW (12 min 28 sec)


That will give some excitement!
Old Aug 11, 2011, 02:31 PM
wishawhunk is offline
Find More Posts by wishawhunk
Quote:
Originally Posted by Bowerz View Post
i suggest doing what these guys do in the second part of their video.

http://www.youtube.com/watch?v=t3xmik3AO7g

That will give some excitement!
God they guys are so annyoing!
Old Aug 12, 2011, 01:20 AM
Kris... is offline
Find More Posts by Kris...
Registered Addict
Kris...'s Avatar
Quote:
Originally Posted by Bowerz View Post
Here's my bay:

You would have been better putting a smaller RX in or taking it out of its orange shell as where it is placed now, on impact the lipo will take the RX out with it when the lipo bail's out.
Old Aug 12, 2011, 04:22 AM
Bowerz is offline
Find More Posts by Bowerz
Once crash at a time
Bowerz's Avatar
Quote:
Originally Posted by KRIS... View Post
You would have been better putting a smaller RX in or taking it out of its orange shell as where it is placed now, on impact the lipo will take the RX out with it when the lipo bail's out.
I did have it positioned to the side of the lipo but tis hard to close the hatch. You wouldn't have thought it, but i've nose this one in hard and it was completely fine, the battery hatch popped and the lipo was laying still attatched to the esc outside of the plane, but nothing broken.
Old Aug 12, 2011, 07:54 AM
aeromaniac is offline
Find More Posts by aeromaniac
Glow 😡 no no no
I use standard Ca on mine and it seems ok.
Old Aug 12, 2011, 08:00 AM
Bowerz is offline
Find More Posts by Bowerz
Once crash at a time
Bowerz's Avatar
I suggest hot glue. epoxy just peeled off evenually after a wing over on launch. I've also run two rods from the back nder the motor mount down through the plane to stop it flexing and strengthen the area around the motor mount. Just sharpened the ends and pushed down through then sealed with hot glue.
Old Aug 12, 2011, 09:40 AM
Kris... is offline
Find More Posts by Kris...
Registered Addict
Kris...'s Avatar
Bowzers right hot glue works best but epoxy can work if you pin hole the area your glueing.
Old Aug 12, 2011, 05:16 PM
wishawhunk is offline
Find More Posts by wishawhunk
Need some helps folks
How do i set this thing up with a dx7?
Also i cant get my esc to arm.Just keeps beeping!
my throttle is right back but i cant think what else?

Thanks

All sorted
Last edited by wishawhunk; Aug 12, 2011 at 05:58 PM.
Old Aug 12, 2011, 07:56 PM
aeromaniac is offline
Find More Posts by aeromaniac
Glow 😡 no no no
Quote:
Originally Posted by wishawhunk View Post
Need some helps folks
How do i set this thing up with a dx7?
Also i cant get my esc to arm.Just keeps beeping!
my throttle is right back but i cant think what else?

Thanks

All sorted
You could try reversing the throttle, the esc might think it is wot, even though it is down.
Old Aug 13, 2011, 01:00 AM
Kris... is offline
Find More Posts by Kris...
Registered Addict
Kris...'s Avatar
Quote:
Originally Posted by wishawhunk View Post
Need some helps folks
How do i set this thing up with a dx7?
Also i cant get my esc to arm.Just keeps beeping!
my throttle is right back but i cant think what else?

Thanks

All sorted
Try trimming the throttle down a couple of clicks.
Old Aug 13, 2011, 02:38 AM
wishawhunk is offline
Find More Posts by wishawhunk
After doing lots of reading it was the the throttle trim that wasnt all the way down. god its amazing wot you learn.
Old Aug 13, 2011, 03:52 AM
Kris... is offline
Find More Posts by Kris...
Registered Addict
Kris...'s Avatar
Quote:
Originally Posted by wishawhunk View Post
After doing lots of reading it was the the throttle trim that wasnt all the way down. god its amazing wot you learn.
Told ya !
Old Aug 13, 2011, 04:57 PM
wishawhunk is offline
Find More Posts by wishawhunk
Quote:
Originally Posted by kris... View Post
told ya !

:d:d:d:d:d
Old Aug 14, 2011, 04:24 PM
wishawhunk is offline
Find More Posts by wishawhunk
Just maidended the plane and it didnt fly at all!

1. Is the number on the props supposed to face you from the back of the plane? i have mins so that the numbers face the nose?
2. Is the motor mean to spin clockwise when looking from behind the plane?

Cant think of anything else?

Thanks

Btw the motor mount is crap. Ordered a parkzone styker one to see if that works
Last edited by wishawhunk; Aug 14, 2011 at 05:03 PM.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Build Log Hobby king's Decathlon EP ARF, 49in. span. SabreHawk Scale ARF/RTF 297 Nov 12, 2015 12:46 PM
Discussion Hobby King Spektrum-like RX hoppy Radios 15 Sep 25, 2010 11:21 PM
Video Hobby Lobby DeHavilland DHC-2 Beaver ARF w/Floats & Wheels Jason Cole Electric Plane Talk 38 May 20, 2010 04:37 PM
Discussion Would Like To By A E Motor Equivalent Of An E-flite 46 In Hobby King FedericoA Power Systems 4 Sep 21, 2009 06:50 AM