Shop our Airplanes Products Drone Products Sales
Thread Tools
Old Jul 16, 2010, 11:50 PM
billpa is offline
Find More Posts by billpa
billpa's Avatar
Discussion

Please post photos of your sensor installations here!


Here's a small collection of sensor installations, for starters.

http://www.eagletreesystems.com/Support/photos.htm

Please post others here!
Site Sponsor
Sign up now
to remove ads between posts
Old Jul 17, 2010, 09:32 AM
garris2 is offline
Find More Posts by garris2
Registered User
This is some pics of Eagletree's baro airspeed and altitude sensors embedded in the wing of my Cularis glider. I'm using them with my FPV setup.
I carved a groove on the bottom side of the wing over the servo wire channel, this allowed me to run the daisy chain wire to the root of the wing where an additional connector mates up when I plug the wings into the fuselage. I have a piece of lexan covering them. Its sunk into the wing flush with the surface. There is nothing protruding except the pitot tube.

Geoff
Last edited by garris2; Jul 17, 2010 at 10:10 AM.
Old Jul 17, 2010, 12:01 PM
dicharry is offline
Find More Posts by dicharry
Registered User
Thanks Billpa for this sticky. There are some great ideas here and I'm sure the list will grow. A picture IS worth a thousand words.
Old Jul 27, 2010, 10:56 AM
Rem 1973 is offline
Find More Posts by Rem 1973
Registered User
Rem 1973's Avatar
Here are two photo's of my installed Optical RPM sensor, and Temp sensor.
Installed on a RCMK 2 stroke gas motor.

Greetings,
Remco.
Old Sep 19, 2010, 09:02 AM
nick_cool is offline
Find More Posts by nick_cool
y chucu, chucu, chuuuu...
nick_cool's Avatar

RPM sensor


Here they are my brushless sensors installed.

The first has two needles soldered.

For the second I made two male-female adapters (3mm bullet)

Good landings
Old Sep 20, 2010, 11:33 AM
pda75 is offline
Find More Posts by pda75
any calculation so far ?
pda75's Avatar
here is mine

Before and after....

Cheers

Pierre
Old Sep 27, 2010, 01:02 PM
Terry Keeley is offline
Find More Posts by Terry Keeley
Registered User

Rpm sensor.


Attached the sensor with heat shrink, bored the hole in flywheel with 0.0005" press fit. Works great!

Old Apr 06, 2011, 01:23 PM
ValBoo is offline
Find More Posts by ValBoo
Registered User
Hi Terry,
Nice install... thanks for the good pic.
Old Jul 09, 2011, 06:21 AM
Eddy de Vries is offline
Find More Posts by Eddy de Vries
Registered User
Here are some pics of how I mounted the magnetic RPM sensor in my Zenoah 2 stroke outboard. I secured the sensor with heat shrink afterwards.

Rgds, Eddy


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Please Post your Aerial Photos here.... kepople Aerial Photography 264 Nov 21, 2016 11:21 AM
Discussion Please post your brushless motor pole count here billpa Eagle Tree Systems 91 May 05, 2015 01:31 AM
Please Post your Aerial Photos here....See Aerial Photo Forum kepople Aerial Photography 234 Apr 29, 2015 12:29 PM
Gallery NEW ENGLAND AEROTOW 2009 - Picture & Comment Thread -- post your photos here! SPasierb Scale Sailplanes 56 Oct 21, 2009 09:59 AM
Post your do-it-yourself photos here! Martin Hunter Parkflyers 35 Jun 25, 2002 12:08 PM