New Products Flash Sale
Thread Tools
Old Jun 22, 2003, 02:00 PM
Takao Shimizu is offline
Find More Posts by Takao Shimizu
Registered User

One hour CD_ROM motor construction


This is CD ROM motor easy construcion without rewinding.
Sign up now
to remove ads between posts
Old Jun 22, 2003, 02:05 PM
Takao Shimizu is offline
Find More Posts by Takao Shimizu
Registered User

One hour CD_ROM motor construction


Change Y to Delta.
Old Jun 22, 2003, 02:07 PM
Takao Shimizu is offline
Find More Posts by Takao Shimizu
Registered User

One hour CD_ROM motor construction


Just termination wiring change.
Old Jun 22, 2003, 02:11 PM
Takao Shimizu is offline
Find More Posts by Takao Shimizu
Registered User

One hour CD_ROM motor construction


CA the prop shaft with PET 5mm nut for prop screw shaft.
Last edited by Takao Shimizu; Jun 23, 2003 at 08:44 AM.
Old Jun 22, 2003, 02:14 PM
Takao Shimizu is offline
Find More Posts by Takao Shimizu
Registered User

One hour CD_ROM motor construction


Test result;
GWS 8043, 6V, 2.4A, Thrust 83g, 3720rpm
Old Jun 22, 2003, 02:56 PM
jmbig is offline
Find More Posts by jmbig
Registered User
Delta does give a better torque range!!! CU
Old Jun 23, 2003, 08:40 AM
Takao Shimizu is offline
Find More Posts by Takao Shimizu
Registered User

One hour CD_ROM motor construction


This is the original Y termination.
Old Jun 23, 2003, 09:04 AM
Robbie d is offline
Find More Posts by Robbie d
Crazy Cessna Owner
Robbie d's Avatar
very informative

is there a one hour convert your speed control to brushless speed control????
Old Jun 23, 2003, 08:21 PM
Takao Shimizu is offline
Find More Posts by Takao Shimizu
Registered User
Robbie d,

>is there a one hour convert your speed control to brushless speed control????

Not yet.
Old Jun 27, 2003, 09:51 PM
Takao Shimizu is offline
Find More Posts by Takao Shimizu
Registered User

More details


You may need motor mount cutting.
I use just hand powered cutter tool($7) and sand paper.
Old Jun 27, 2003, 09:54 PM
Takao Shimizu is offline
Find More Posts by Takao Shimizu
Registered User

More details


De-solder and de-twist at the Y coil connection point.
De-paint is usefule to nude-off the coil wire paint.
Old Jun 27, 2003, 09:56 PM
Takao Shimizu is offline
Find More Posts by Takao Shimizu
Registered User
Put on the plane.
Old Jun 27, 2003, 09:58 PM
Takao Shimizu is offline
Find More Posts by Takao Shimizu
Registered User

Ready to test fly


You may need the timing adjust of ESC.
4A ESC is enough to drive this.
Old Jun 28, 2003, 09:12 AM
ssatoru is offline
Find More Posts by ssatoru
Registered User
ssatoru's Avatar

Another ready to fly


I am also modifying the same CDROM motor. Only different way to mount on the plane. Ready to fly tomorrow.

YG-F1G Delta wind
GWS 6x5SF 7.29V 2.25A 16.40W 5,520rpm

rewound with 0.4mm 20T
GWS 7x6SF 5.63V 5.86A 33.00W 4,010rpm
GWS 6x5SF 6.10V 4.92A 30.00W 6,720rpm

satoru
Old Jun 28, 2003, 12:21 PM
bz1mcr is offline
Find More Posts by bz1mcr
AKA Don
This is a great contribution. I can't wait to get started on a conversion myself.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
One hour CD ROM motor construction PART2 Takao Shimizu Power Systems 754 Sep 08, 2010 01:12 PM
One hour CD ROM construction part 7 rysium Power Systems 806 Dec 18, 2006 03:58 AM
One hour CD ROM construction part 6 arx_n_sparx Power Systems 1050 Mar 10, 2005 08:08 PM
One Hour CD ROM Construction Part 5 arx_n_sparx Power Systems 537 May 07, 2004 10:56 AM
One hour CD ROM motor construction PART3 rysium Power Systems 511 Mar 22, 2004 02:03 PM