E-flite Blade SR 120 Thread. - Page 913 - RC Groups
Thread Tools
Jun 08, 2012, 07:10 AM
Wind you go around in circles
Wind Spirit's Avatar
Quote:
Originally Posted by micro2000

Are you sure it was 2meters to the left and not 2ft? That's a hell of a drift...


Yes, it is more like two feet, as the kitchen area I am trying it in is only 8 feet square. Thanks for the tips, I will try and be more assertive on take off[/QUOTE]

Hi, Thats a very small area for the 120 but can be done. When I first got my 120 and was flying inside if I was slow on the throttle, at about 6" or 1' she would drift left very fast and I would shut her down and start over and she would to the same over and over. You will find that with a little faster lift and at about 3 to 4' she will smooth out and should be able to get a good hover.WS
Sign up now
to remove ads between posts
Jun 08, 2012, 08:05 AM
Rock-n-Aileron Roll!
Saxguy1000's Avatar
I just made a significant discovery. Last night my tail motor got so hot that it melted the rotor so that the enlarged hole caused the heli to spin w/o rotor control.. Also, it Had been melting the hot glue I applied to keep it in the holder. So, it was super calm this morning and I just slapped on the first spare I had, a Solo Pro 328 tail rotor. Wow! This thing is not bendy like the 120's. It's got the same exact specs except it is stiff and you know what? I just flew for 8:15 and the tail rotor wasn't hot and the hot glue wasn't melted. It never occurred to me before that my tail motors were probably burning out because of my flexing or mishapen rotors.
Jun 08, 2012, 08:38 AM
Wind you go around in circles
Wind Spirit's Avatar
Quote:
Originally Posted by Saxguy1000
I just made a significant discovery. Last night my tail motor got so hot that it melted the rotor so that the enlarged hole caused the heli to spin w/o rotor control.. Also, it Had been melting the hot glue I applied to keep it in the holder. So, it was super calm this morning and I just slapped on the first spare I had, a Solo Pro 328 tail rotor. Wow! This thing is not bendy like the 120's. It's got the same exact specs except it is stiff and you know what? I just flew for 8:15 and the tail rotor wasn't hot and the hot glue wasn't melted. It never occurred to me before that my tail motors were probably burning out because of my flexing or mishapen rotors.
That is very interesting, I was told that the tip of a prop is where all of the good things happen from friends that have air boats, so if you think about it all that flex in the rotor has to be somewhat changeing the pitch and reduceing the amount of air flow. The flexing may help in a crash but I am sure it is no help in tail control. So the 328 being rigid should be a great improvement. Good one Sax, how is the fit on the shaft?WS
Jun 08, 2012, 08:44 AM
Rock-n-Aileron Roll!
Saxguy1000's Avatar
Fits tightly--just right.
Jun 08, 2012, 08:57 AM
Wind you go around in circles
Wind Spirit's Avatar
Quote:
Originally Posted by Saxguy1000
Fits tightly--just right.
Thanks, Will order some.WS
Jun 08, 2012, 09:52 AM
Look ma, no hands!
1Pilgrim's Avatar
Quote:
Originally Posted by Cobraxix70
So, I just recieved my DX6i in the post and downloaded Mr. Salts handbook....

All of a sudden, I'm totally overwhelmed....
I had to start out by familiarizing myself with all the different screens. The manual lays them out in such a weird way that it's hard to follow. Mr. Salt's book is better but the way he scrambles the dx6i and dx7 together can be confusing.

As usual, Mike is right when he suggests starting with the basics - set up your tx just the way Mr. Salt recommends and fly for a while, then start making small "tweaks" just to see what happens.

It takes 40 hours of dual instruction to solo a Cessna which is arguably one of the easiest light aircraft to fly. The 120 is a lot harder - no instructor in the left seat. Take your time and enjoy the learning process - and stock up on spare parts!
Jun 08, 2012, 10:01 AM
Registered User
Quote:
Originally Posted by 1Pilgrim
and stock up on spare parts!
Oh I have a fully stocked 'crash pack'. Bust as of recent I've not had any incidents.
I think I've broken throught the learning 'wall'.
Now, the DX6i is another story...

Thank you to all who take the time to reply here.
Jun 08, 2012, 10:08 AM
Look ma, no hands!
1Pilgrim's Avatar
Quote:
Originally Posted by Cobraxix70
Thank you to all who take the time to reply here.
Hey, swapping tips tricks and lies about our helis is half the fun!
Jun 08, 2012, 10:08 AM
Epilepsy Awareness
Chap1012's Avatar
^^^^
When you use the roller make darn sure you press it at the TOP when you need to change menus.

Mike.
Jun 08, 2012, 11:36 AM
Look ma, no hands!
1Pilgrim's Avatar
Quote:
Originally Posted by Chap1012
^^^^
When you use the roller make darn sure you press it at the TOP when you need to change menus.

Mike.
Yeah, I've read that the roller bar is fragile - hasn't been a problem for me yet but it would be nice to know if and how it can be repaired.
Jun 08, 2012, 12:02 PM
Epilepsy Awareness
Chap1012's Avatar
Quote:
Originally Posted by 1Pilgrim
Yeah, I've read that the roller bar is fragile - hasn't been a problem for me yet but it would be nice to know if and how it can be repaired.
You can't buy the roller. You must send it back to HH for repair. They will not sell you just the roller. In fact, the "only" part that I know of that you can buy and repair it yourself is the antenna. I've read some posts that guys fix the wheel using CA and gussets with great success.

Mike.
Last edited by Chap1012; Jun 08, 2012 at 04:56 PM. Reason: not a "wheel"
Jun 08, 2012, 12:17 PM
Wind you go around in circles
Wind Spirit's Avatar

Spektrum roller


Pilgrim & Chap, Maybe I can help,if I get this right.WS http://www.eastrc.org/shop.cgi/page=...242086050.1641
Jun 08, 2012, 12:21 PM
Wind you go around in circles
Wind Spirit's Avatar
Quote:
Originally Posted by Wind Spirit
Pilgrim & Chap, Maybe I can help,if I get this right.WS http://www.eastrc.org/shop.cgi/page=...242086050.1641
I think the upgrade is metal and not plastic, been saving this link just in case.WS
Jun 08, 2012, 12:36 PM
Registered User
Quote:
Originally Posted by 1Pilgrim
Yeah, I've read that the roller bar is fragile - hasn't been a problem for me yet but it would be nice to know if and how it can be repaired.
There is replacement metal roller knobs for the Spektrum DX xmitters.

http://www.eastrc.org/estorerollerbutton.htm

You'll void the warranty putting it in. Spektrum should have made the radio this way in the first place. In quantity it would probably only add a few cents to the cost of the radio.

While you're at it, you could add the screen backlight for the display.
Jun 08, 2012, 02:28 PM
Against Helicopter Cruelty
Heli Pad's Avatar
I ordered a set of Align Trex 250 skids for my 120SR. It arrived in the mail today. I haven't taken it out of the package yet. I'm kinda busy with something else and will get to it tomorrow or so.

But it appears that it doesn't have the same hardware to mount directly to the 120SR frame. I know that several people here use that skid. May I ask, what is the recommended way from installing the 250 skids on the 120SR. Would you mind sharing your experience and recommendation with me? Thanks.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product Blade SR RTF Electric Micro Heli by E-flite ghost2212 Micro Helis 6658 Oct 28, 2015 09:24 AM
Discussion Update Blade CP or buy E-Flite Blade SR or 400? markhwing Electric Heli Talk 10 Aug 06, 2012 04:16 PM
Link E-flite mSR batteries E flite 110-120 Hyp.CX 120 and others everydayflyer Batteries and Chargers 45 Apr 08, 2010 05:55 AM
For Sale Did you just buy a new E-Flite Blade SR? Z06 Tony Aircraft - Electric - Helis (FS/W) 3 Feb 28, 2010 01:01 AM
New Product Blade SR RTF Electric Micro Heli by E-flite ghost2212 Micro Ready-to-Fly 2 Jan 07, 2010 10:36 AM