Feb 10, 2013, 11:52 AM
Registered User
Freakazoid's Avatar
No, not the afromini, but one of the flips I bought from you.
Sign up now
to remove ads between posts
Feb 15, 2013, 02:18 PM
If it flies, I can crash it!
djdavid60's Avatar
Wow! Five days without a single post. A new thread record?
Feb 15, 2013, 02:23 PM
Registered User
rimshotcopter's Avatar
Quote:
Originally Posted by djdavid60 View Post
Wow! Five days without a single post. A new thread record?
Agreed!
Feb 15, 2013, 03:39 PM
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Where are all those MultiWii-er..
Feb 15, 2013, 03:40 PM
throw new IOPilotException();
IceWind's Avatar
In the Multiwii forum!
Feb 15, 2013, 05:49 PM
Registered User
Hi, I installed a new multiwii:
Vue de Robermont 13-02-13 (1 min 4 sec)

When I activate the baro, the quad is the yoyo. I had to disable it ... How to have a good setup? Is it really accurate / useful? The sensor BMP085 baro is.
Feb 15, 2013, 06:22 PM
Design > Build > Fly
Qrome's Avatar
Quote:
Originally Posted by majr View Post
Hi, I installed a new multiwii:
http://www.youtube.com/watch?v=gRrH7...&feature=share
When I activate the baro, the quad is the yoyo. I had to disable it ... How to have a good setup? Is it really accurate / useful? The sensor BMP085 baro is.
You may need to cover the baro in foam or protect it from the wind blast from the props if you have not done so already.
Feb 15, 2013, 10:09 PM
Emress
anybody need auto 3-axis stabilization on the cheap?

Feb 16, 2013, 10:43 AM
Registered User
Quote:
Originally Posted by Qrome View Post
You may need to cover the baro in foam or protect it from the wind blast from the props if you have not done so already.
I covered with neoprene... What is the method to adjust the PID for the baro?
Feb 16, 2013, 03:28 PM
Registered User
Quote:
Originally Posted by majr View Post
I covered with neoprene... What is the method to adjust the PID for the baro?
The covering MUST be air conductive, you must be able to blow through it. Not closed cell plastic or foam. A couple of layers of cotton fabric have worked for me. These can also be affected by direct sun light, or so I have read?
Feb 17, 2013, 10:14 PM
Registered User
OK how do you delete a post!!!
Last edited by coolthoughts; Feb 17, 2013 at 10:22 PM. Reason: I can't find a delete button!
Feb 19, 2013, 05:56 PM
If it flies, I will crash it
mxspode's Avatar
There is no "Delete". Only "Edit", of which you have discovered.

Rob...
Feb 19, 2013, 09:09 PM
Registered User

thanks for this post!


Quote:
Originally Posted by GALENM View Post
I have been flying my quad with the Parris Aerial photo board for over a year. Recently it crashed breaking a couple arms but did not show damage to the board. After repairs I do not have response from the board. I checked and found the 5 volts at the inputs from the Speed control but nothing at the receiver output.
As noted in the picture there are a pair of connection blocks in the line from the Speed controller connections to the receiver output.

If I would put a drop of solder there it would complete the connection to the receiver. Not sure how it was supplied before. Any problem in making this connection.

I have solved my own problem. I made a jumper to connect the 5 volts available on the Speed controller input block to the + on the receiver block. A quick test shows everything working. I suspect closing the jumper blocks would do the same but that change would be hard to reverse
I had the same problem where I wasn't getting power to my receiver. After reading this post I noticed a break on my board. Soldered a couple strands of wire and my receiver now gets power.

Thanks!
Last edited by rcrider28; May 05, 2013 at 07:45 AM.
Feb 20, 2013, 09:46 AM
Registered User
M4d_D's Avatar
hi, just a quick question...
can anyone explain to me how to set up the multiwii failsafe when using a computer radio.

since my radio has its own failsafe multiwii wont be able to detect of i still have control or if its just failsafe, so my default failsafe is to switch off the motors and let the model drop.

i would rather like the multiwii failsafe to ckick in then, so it would switch on the acc and let the motors run slowly for a while, so it would "land" wherever it is but it wont drop like a stone...

any ideas ???

cheers
Feb 20, 2013, 10:18 AM
Registered User
Freakazoid's Avatar
That request actually gave me an idea that could help overcome the failsafe-ontop-of-failsafe problem.
Wouldn't it be cool if we could have one of the AUX channels trigger an automatic self-level & descent feature?
It would pretty much give you a panic button as well as your receiver failsafe being able to trigger it on its own.