Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Dec 09, 2012, 05:20 PM
ChilternFlyer is offline
Find More Posts by ChilternFlyer
Still flying a desk..
ChilternFlyer's Avatar
Quote:
Originally Posted by blackbrabus View Post
So the Mrs spotted the tricopter all illuminated and now I have a new winter project (well 2 week).....I have to set my little boys ikea kitchen up so that it has a lit oven and microwave and even a under shelf light.....so giant shark just got an order for LEDs and cable and just deciding if I should get a little lipo to power it or just use a 9v bat......and all for xmas day when he gets it

Attachment 5361658
Ahh! Bless.
Sign up now
to remove ads between posts
Old Dec 09, 2012, 05:26 PM
MikeTheCrash is offline
Find More Posts by MikeTheCrash
Just clumsy. Oh, forgetful too
MikeTheCrash's Avatar
Quote:
Originally Posted by blackbrabus View Post
So the Mrs spotted the tricopter all illuminated and now I have a new winter project (well 2 week).....I have to set my little boys ikea kitchen up so that it has a lit oven and microwave and even a under shelf light.....so giant shark just got an order for LEDs and cable and just deciding if I should get a little lipo to power it or just use a 9v bat......and all for xmas day when he gets it

Attachment 5361658
you can get reels of the LEDs from ebay and lots come with a controller and mains transformer...I'd personally not let a lipo near my kids as I can't even be trusted with them myself. 9v battery might be the safest!
Old Dec 09, 2012, 05:30 PM
Carlos230023 is offline
Find More Posts by Carlos230023
um.. yeah, I can make that fly
Carlos230023's Avatar
What happens when you over discharge a 9v battery, not alot. What happens when you over discharge a lipo... I'd go 9v square cell or mains with a power brick tbh :P.

CJ
Old Dec 09, 2012, 05:59 PM
ChilternFlyer is offline
Find More Posts by ChilternFlyer
Still flying a desk..
ChilternFlyer's Avatar
Quote:
Originally Posted by MikeTheCrash View Post
you can get reels of the LEDs from ebay and lots come with a controller and mains transformer...I'd personally not let a lipo near my kids as I can't even be trusted with them myself. 9v battery might be the safest!
Don't feel to bad about it Mike. My brother in-law recently told me that another well known modeler also had a li-po accident and had the fire brigade in attendance.

I bought some li-po sacks after that!
Old Dec 09, 2012, 06:27 PM
Carlos230023 is offline
Find More Posts by Carlos230023
um.. yeah, I can make that fly
Carlos230023's Avatar
Stuff lipo sacks! Old army ammo cases are the way forward :P. they're cheap too!

CJ
Old Dec 09, 2012, 06:33 PM
blackbrabus is offline
Find More Posts by blackbrabus
If it flies.....I can crash it
blackbrabus's Avatar
9v batt it is then.....just ordered all the switches etc etc....should be fun blinging it out.

And I have an ammo case for all my lipos as well.
Old Dec 09, 2012, 06:36 PM
lewpix is offline
Find More Posts by lewpix
Registered User
Right, finally got some time to try and finish my skywalker and got a slight problem. I'm using the aurora 9 tx (through ezuhf) to a hornet osd and fy31ap in the plane. There is a function to change the screens in the OSD that i've put in channel 8 but it doesnt work. In the manual it says the PWM signal of the 2 way switch is 900us ~ 1200us and 1800us~2100us (the symbol is a u with a longer tail followed by an s) now i've tried every switch and dial in the aurora to no avail, and there is no mention of changing 'us' levels for the switches in the manual. I could run the OSD on the default screen which shows everything, but would rather have the option to change it. There is probably something really obvious that I've overlooked, but after hours of research, trial and error and just plain guess work I can only apologise if the answer is obvious, 'cos i'm stumped! Any advise gratefully received, really want this thing done so I can look at the multicopters that are queing up!
Old Dec 09, 2012, 07:06 PM
highviz is offline
Find More Posts by highviz
Registered User
Quote:
Originally Posted by lewpix View Post
Right, finally got some time to try and finish my skywalker and got a slight problem. I'm using the aurora 9 tx (through ezuhf) to a hornet osd and fy31ap in the plane. There is a function to change the screens in the OSD that i've put in channel 8 but it doesnt work. In the manual it says the PWM signal of the 2 way switch is 900us ~ 1200us and 1800us~2100us (the symbol is a u with a longer tail followed by an s) now i've tried every switch and dial in the aurora to no avail, and there is no mention of changing 'us' levels for the switches in the manual. I could run the OSD on the default screen which shows everything, but would rather have the option to change it. There is probably something really obvious that I've overlooked, but after hours of research, trial and error and just plain guess work I can only apologise if the answer is obvious, 'cos i'm stumped! Any advise gratefully received, really want this thing done so I can look at the multicopters that are queing up!
The microsecond ranges just relate to the full throw positions of the switches. Mid position is usually somewhere around 1500, and the upper and lower ends are 1000 / 2000 (or somewhere close). Try adjusting the travel limits (ATV's) on the channel / switch you want to use.

Malc
Old Dec 09, 2012, 07:39 PM
ghost2212 is offline
Find More Posts by ghost2212
Skint since 2000
ghost2212's Avatar
http://www.ebay.co.uk/itm/faulty-fat...item35c26ba565

Was linked on BMFA classifieds, Anyone on heres?

I know its not mine
Old Dec 09, 2012, 07:45 PM
mudlark is online now
Find More Posts by mudlark
Happy Days
mudlark's Avatar
Quote:
Originally Posted by ghost2212 View Post
http://www.ebay.co.uk/itm/faulty-fat...item35c26ba565

Was linked on BMFA classifieds, Anyone on heres?

I know its not mine
not seen it before.
Old Dec 09, 2012, 08:25 PM
Aviefly is offline
Find More Posts by Aviefly
Registered User
Aviefly's Avatar
LOL the numb skull didn't even have the sense to unplug the lipo
Old Dec 09, 2012, 09:43 PM
lewpix is offline
Find More Posts by lewpix
Registered User
Hmmm... it's channel 8 that isn't working, tried every setting before deciding to switch the leads over on the rx and when plugged in to channel 7 it works perfectly. Will try putting it back as it was but swapping the channels over in the tx programming to see if it is the tx, if that doesn't affect it will unplg the rx from the plane and try a firmware update on that, as something on immersion website mentions a problem with channel 8 and a firmware that solves it, however I put the latest version on to the rx before installing it. I think....
Old Dec 09, 2012, 10:38 PM
lewpix is offline
Find More Posts by lewpix
Registered User
Problem solved, seems immersion must have updated the firmware for the ezuhf since i started the build to solve a channel 8 problem. I had no idea there was a problem until now, PITA as it's now 3.35am but everything now works so I can stick the plane together when I get time.
Old Dec 10, 2012, 04:17 AM
MikeTheCrash is offline
Find More Posts by MikeTheCrash
Just clumsy. Oh, forgetful too
MikeTheCrash's Avatar
Quote:
Originally Posted by blackbrabus View Post
9v batt it is then.....just ordered all the switches etc etc....should be fun blinging it out.

And I have an ammo case for all my lipos as well.
sorry to flog a dead horse but I decided you should get a 12v gel cell that you can recharge and thought you should know
Old Dec 10, 2012, 04:19 AM
MikeTheCrash is offline
Find More Posts by MikeTheCrash
Just clumsy. Oh, forgetful too
MikeTheCrash's Avatar
Quote:
Originally Posted by ChilternFlyer View Post
Don't feel to bad about it Mike. My brother in-law recently told me that another well known modeler also had a li-po accident and had the fire brigade in attendance.

I bought some li-po sacks after that!
house is nearly fixed, may move back in next Wednesday!


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion FPV Car and Other Fun FPV Projects Thread: Crash9 FPV Talk 11331 Nov 21, 2016 11:08 PM
Discussion UK to France FPV srjs FPV Talk 98 Jul 21, 2016 03:14 PM
For Sale FPV Stuffs UK QUIKSILVER Aircraft - General - Radio Equipment (FS/W) 19 Jan 31, 2016 03:37 PM
Discussion can we have a uk section in the for sales thread please? kieran3008 Site Chat 28 Apr 17, 2014 03:13 PM
Discussion FPV WARS (Thread for FPV "B" Movies) ch1 FPV Talk 8 Sep 16, 2009 06:37 PM