Thread Tools
Old May 07, 2010, 05:52 PM
Clintstone is offline
Find More Posts by Clintstone
Castle Support
Clintstone's Avatar
Mini-HowTo

Castle Quick Tip: Throttle Calibration Part 1 of 2


Video to help with Throttle Calibration on a Heli.
This is a tutorial video that I made to help make throttle calibration on Castle Creations ESCs easier. This video is made using a Heli but it can also be applied to an airplane.

You can also find more info at : http://www.castlecreations.com/




Castle Quick Tip- Throttle Calibration.wmv (3 min 23 sec)
Last edited by Clintstone; Jun 08, 2010 at 04:00 PM.
Sign up now
to remove ads between posts
Old May 11, 2010, 09:58 AM
dfrazier is offline
Find More Posts by dfrazier
Registered User
Good video
Old Jun 11, 2010, 03:19 AM
monkey1 is offline
Find More Posts by monkey1
Registered User
i cant see your TX parameters selection! And voice also small. Any more better quality video?
Old Jun 14, 2010, 03:39 PM
Clintstone is offline
Find More Posts by Clintstone
Castle Support
Clintstone's Avatar
I will be making a higher quality video soon. Thanks for your patience.
Old Jun 16, 2010, 12:18 PM
GBR2 is offline
Find More Posts by GBR2
Stress Be Gone
GBR2's Avatar
Are the videos available for download on the Castle site? If so where as I've not been able to find them.
Old Jun 23, 2010, 04:15 PM
GBR2 is offline
Find More Posts by GBR2
Stress Be Gone
GBR2's Avatar
Yes, but all that does is link to the YouTube videos. I'd like to have the videos downloadable so that you don't need an internet connection to watch them.
Old Jun 24, 2010, 03:31 AM
Clintstone is offline
Find More Posts by Clintstone
Castle Support
Clintstone's Avatar
Quote:
Originally Posted by GBR2 View Post
Yes, but all that does is link to the YouTube videos. I'd like to have the videos downloadable so that you don't need an internet connection to watch them.
there are several open source programs that let you download you tube videos I believe. I am hoping to re-make the videos next week with higher quality video and sound. The original videos were posted on you tube so we could get them up quickly.
Old Feb 04, 2011, 07:31 PM
zigaspire is offline
Find More Posts by zigaspire
Registered User
I have an old, non-computerized 3 channel transmitter. I have an outunner motor that is a little too powerful for my 2 meter sailplane. I want to be able to program the ESC to only allow about 75% power to the motor when the radio puts out full throttle.

Is this possible with a Castle Creations ESC using Castle Link? I have not purchased the ESC yet.

Thanks.
Old Feb 05, 2011, 08:31 AM
flarssen is online now
Find More Posts by flarssen
Registered User
I have a CC Phx10 on v3.20.
Tx is Robbe/Futaba FC-18.
To get the confirmation beep on high setting I need to set ATV to 110% (max) and then put the trim above centre. For the low setting it initializes when ATV is set to 62% with trim in the normal low position, and 80% when trim i centred.
What is the values in ms for the fixed endpoints? Obviously far from what my Tx operates on, but any servo plugged in to ch 3 behaved quite normal.
Calibrating the Tx against fixed values in the ESC seems somehow backwards to me. What is wrong with the "full stick, power on ESC, pull stick" method used by others for throttle calibration?

Edit: Got it working now with full up trim. ATV's ended then at 96% (High) and 104% (Low). A bit unusual I guess, and a pain since my Assan module (2.4GHz) refuses to initialize unless throttle is at it's lowest (+ trim).


Fred
Last edited by flarssen; Feb 05, 2011 at 10:10 AM.
Old Mar 16, 2011, 03:27 PM
Clintstone is offline
Find More Posts by Clintstone
Castle Support
Clintstone's Avatar
Quote:
Originally Posted by flarssen View Post
I have a CC Phx10 on v3.20.
Tx is Robbe/Futaba FC-18.
To get the confirmation beep on high setting I need to set ATV to 110% (max) and then put the trim above centre. For the low setting it initializes when ATV is set to 62% with trim in the normal low position, and 80% when trim i centred.
What is the values in ms for the fixed endpoints? Obviously far from what my Tx operates on, but any servo plugged in to ch 3 behaved quite normal.
Calibrating the Tx against fixed values in the ESC seems somehow backwards to me. What is wrong with the "full stick, power on ESC, pull stick" method used by others for throttle calibration?

Edit: Got it working now with full up trim. ATV's ended then at 96% (High) and 104% (Low). A bit unusual I guess, and a pain since my Assan module (2.4GHz) refuses to initialize unless throttle is at it's lowest (+ trim).


Fred
You should be able to pull the trim down to satisfy... then calibrate the throttle with the trim down... as long as you leave the trim down then it should not change...
Old Mar 16, 2011, 04:19 PM
66tbird is offline
Find More Posts by 66tbird
To many projects
66tbird's Avatar
On my phx45 using a 9303 I can find the high but not the low.

Just to test I set it for functionality I did a simple, 'airplane' mode and 'auto endpoints' and all it does is enter program mode on travel extremes.

btw the esc hasn't spun a motor yet
Last edited by 66tbird; Mar 25, 2011 at 11:40 AM. Reason: Problem solved, just had to understand the the way it works. Thanks for the help
Old Mar 16, 2011, 05:14 PM
Clintstone is offline
Find More Posts by Clintstone
Castle Support
Clintstone's Avatar
Quote:
Originally Posted by 66tbird View Post
On my phx45 using a 9303 I can find the high but not the low.

Just to test I set it for functionality I did a simple, 'airplane' mode and 'auto endpoints' and all it does is enter program mode on travel extremes.

btw the esc hasn't spun a motor yet

Set your throttle type to fixed endpoints and try it again... it should work after set it to fixed endpoints...
Old Mar 17, 2011, 06:05 AM
flarssen is online now
Find More Posts by flarssen
Registered User
Quote:
Originally Posted by Clintstone View Post
You should be able to pull the trim down to satisfy... then calibrate the throttle with the trim down... as long as you leave the trim down then it should not change...
If I understand this correct, the ESC has fixed settings for min and max throttle in governor mode and the idea is to adjust the Tx travel according to those.
As I said, with trim down, reaching the upper level is impossible with my Tx.

Why not make these settings changeable through the link app?
Old Mar 24, 2011, 01:54 AM
flarssen is online now
Find More Posts by flarssen
Registered User

Problem solved


The problem I had with reaching the high spot was due to the fact that the function throttle ATL (trim have no effect when stick is above neutral), was deactivated by default in heli mode. After setting THR ATL to active, I was able to reach both upper and lower spot.

Fred


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Thunderbird 54 Throttle Calibration Chophop Power Systems 24 Apr 29, 2010 09:37 PM
Discussion Suppo 20A ESC throttle calibration procedure khaled_abobakr Power Systems 7 Apr 10, 2010 05:28 AM
Discussion 3.11 throttle calibration and auto calibration for Helis Clintstone Castle Creations 43 Mar 13, 2010 06:29 AM
Discussion Quick tip for I/R sender speeds Slider2732 Micro Ready-to-Fly 0 Jan 25, 2010 12:11 PM
Discussion CC PHOENIX 35 and auto calibration throttle quenda Castle Creations 9 Dec 06, 2009 08:44 PM