Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Mar 16, 2010, 11:39 PM
rick oshay is offline
Find More Posts by rick oshay
Registered User
Discussion

3.5mm or 4.0mm. bullet male to xt60 female?


Ok guys. I refuse to pay a dollar each for xt60 pairs. I will instead purchase bullet connector pairs but Id like to know which is a better fit, 3.5mm or 4mm.

I measured the xt60 female outer diameter and it tells me 4.0mm

Specs say its 3.5 though.

Any thoughts on this?

Thanks.
Sign up now
to remove ads between posts
Old Mar 17, 2010, 02:01 AM
tjinguy is offline
Find More Posts by tjinguy
TJin(Guy + Tech)
tjinguy's Avatar
Sorry to hear that because XT60s are a very handy connector.

The bullets in them are just a hair under 3.5mm. A male 3.5mm bullets will fit snugly into the holes on the XT60s but the post on the XT60 fits a little loosely in the female 3.5mm bullets.
Old Mar 17, 2010, 12:36 PM
tkallev is offline
Find More Posts by tkallev
LSF303-AMA Fellow
tkallev's Avatar
Quote:
Originally Posted by rick oshay View Post
Ok guys. I refuse to pay a dollar each for xt60 pairs. I will instead purchase bullet connector pairs but Id like to know which is a better fit, 3.5mm or 4mm.

I measured the xt60 female outer diameter and it tells me 4.0mm

Specs say its 3.5 though.

Any thoughts on this?

Thanks.
Just an FYI: measure bullet connectors on the female connector's inside diameter.

There are guys on fleabay who are selling XT60 connectors under $1.00 per pair in bulk packs, just search XT60 connectors. Watch for the shipping origin, some are simply sending you to HK/HC websites.

tk
Old Mar 17, 2010, 01:40 PM
tjinguy is offline
Find More Posts by tjinguy
TJin(Guy + Tech)
tjinguy's Avatar
The best I could do a while back was 20 pairs for $30 shipped.
Old Mar 19, 2010, 12:01 AM
rick oshay is offline
Find More Posts by rick oshay
Registered User
yeah the xt60s I ran into researching are all running a buck something a pair.

I can always spread the post a bit to make a tighter fit.

I thinking of using some silicone tubing to slide over exposed bullets when not using. Then when its time to charge or plug up, pay attention and connect same colors, it shouldnt be that hard for myself. I can match red to red, black to black.


THANKS FOR YOUR TIME GUYS.
Old Mar 19, 2010, 12:31 PM
Dr Kiwi is offline
Find More Posts by Dr Kiwi
Registered User
Dr Kiwi's Avatar
I use plastic "thread protectors" from ACE Hardware to cover exposed male bullets.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Sold 3.5mm Gold Plated Bullet Connectors pttse Aircraft - General - Miscellaneous (FS/W) 0 Mar 05, 2010 01:40 AM
Sold 3.5mm Gold Plated Bullet Connectors ***$1.00 per pair + flat $1.25 shipping*** old_dude Aircraft - General - Miscellaneous (FS/W) 0 Feb 26, 2010 02:06 PM
Discussion Bullet: female or male on motor? cloud-9 Power Systems 4 Feb 08, 2008 09:45 AM
Found 3 Tamiya Male Connectors, 1 Tamiya Female or 2 Female Deans Ultra Plugs Bohh33 Aircraft - Electric - Batteries & Chargers (FS/W) 2 Jan 10, 2008 10:13 PM
WTB: Female & Male Bullet Connectors livinma1 Aircraft - Electric - Airplanes (FS/W) 15 Apr 19, 2005 01:31 AM