Shop our Airplanes Products Drone Products Sales
Thread Tools
Oct 12, 2012, 09:03 AM
There is Victory in the Lord!
knifeedge63's Avatar
Quote:
Originally Posted by ltc
Speaking of hot melt glue, I have always been conservative and used low temp hot melt glue (I know, low temp hot melt...it's like jumbo shrimp; doesn't sound right) on Elapor (and Depron)

Is high tempo/standard hot melt OK for Elapor ?

Also, for those who use CA to mount servos, use caution. You would be surprised where too much (thin) CA can go ... I've heard of servo cases being glued together and glue getting into gears and servo bearings/bushings....
high temp will kinda melt the foam. i use low temp and it works great. i wouldnt worry. and i never use thin CA on anything but building balsa models! if i do CA servos in, i use x-tra thick CA.
Sign up now
to remove ads between posts
Oct 12, 2012, 09:04 AM
Registered User
Quote:
Originally Posted by knifeedge63
Nope just some good sticky painters tape will do. and make sure to wrap around the servos a few times.
What is the pupose of the tape, to keep the glue off the servo case?
Last edited by itsme2; Oct 12, 2012 at 09:29 AM.
Oct 12, 2012, 09:50 AM
There is Victory in the Lord!
knifeedge63's Avatar
Quote:
Originally Posted by itsme2
What is the pupose of the tape, to keep the glue off the servo case?
yeah and it wont tear up the plane when you try and remove the servo. Its just a clean way of installing them... and you will eventually be glad you put them in this way!
Oct 12, 2012, 10:24 AM
Registered User
Del-Dredd's Avatar
Quote:
Originally Posted by Rickflaguy
With a cg slightly forward or equal to 70 mm I "feel" like it is a little too nose heavy. Can some of you chip in your experiences with moving back some and how much?
I fly mine 65 to 70mm without issue flies inverted fine as well with barely a touch of down elevator so not nose heavy.

I have heard of tip stalling with a CoG near the 80mm mentioned in manual.
Oct 12, 2012, 11:33 AM
Registered User

Motor Mount Questions?


My FC kit came with an aluminum motor mount/firewall plate. Is there any good reason to use this alternative aluminum motor mount: http://smallpartscnc.com/index.php?r...&product_id=54

Should I somehow beef up the firewall/motor mounts before I install the motor mount setup? Should I use epoxy on the rail mounts?

Thank you!
Last edited by itsme2; Oct 12, 2012 at 11:40 AM.
Oct 12, 2012, 12:04 PM
Registered User
Is Foam Tac suitable for building the FC especially joining the fuselage halves?

Thank you!
Oct 12, 2012, 01:26 PM
Registered User
JDMJim's Avatar
Quote:
Originally Posted by Del-Dredd
I fly mine 65 to 70mm without issue flies inverted fine as well with barely a touch of down elevator so not nose heavy.

I have heard of tip stalling with a CoG near the 80mm mentioned in manual.
you'll want alot of power if you want the CG that far back.but the plane will do 3D flying that why, hence the power
Oct 12, 2012, 01:36 PM
There is Victory in the Lord!
knifeedge63's Avatar
Quote:
Originally Posted by itsme2
Is Foam Tac suitable for building the FC especially joining the fuselage halves?

Thank you!
Use medium CA. thats the best. nothing else glues elapor better than medium CA. and dont use the foam safe ca. just regular. and the smallparts mount just has holes drilled for MULTIPLE motors. the stock aluminum mount is for the power combo sold by multiplex. but the stock should do fine.
Oct 12, 2012, 02:05 PM
Registered User
Starving Bushman's Avatar
Just a quick tip based on my experience building the FC. Spray one side of the fuselage with CA kicker and let it dry completely. Then put medium CA on the other half, join and brace the 2 together. I suggest the use of the kicker because I tried gluing the motor mount rails in without kicker and like half an hour later the CA still hadn't set up. If you let the kicker dry on the one half before joining them you will have some time to adjust and reposition the 2 halves before it sets up.
Oct 12, 2012, 02:22 PM
Registered User
I just went to Hobby King to order my motor, servos, ESC and BEC plus some other items.

The HS-82MG and HXT-900 servos recommended here are on back order. Can anyone recommend good alternatives from HK, I don't mind paying a little more?

Trying to do a quality build.

Thank you!
Last edited by itsme2; Oct 12, 2012 at 03:15 PM.
Oct 12, 2012, 02:37 PM
There is Victory in the Lord!
knifeedge63's Avatar
Quote:
Originally Posted by itsme2
I just went to Hobby King to order my motor, servos, ESC and BEC plus some other items.

The HS-82MG and HXT-900 servos recommended here are on back order. Can anyone recommend good alternatives from HK, I don't mind paying a little more?

I'm using a 1000KV motor: http://www.hobbyking.com/hobbyking/s...dproduct=18228 Is a 60 amp ESC ok? HK has a 60 amp Turnigy Plush ESC that weighs about the same as the 40 amp. Going to use a BEC too.

Trying to do a quality build.

Thank you!
Just get some HS-55's from your local hobby shop. and they should have some HS-82's as well.. any hobby shop seems to always have those servos in stock.
Oct 12, 2012, 03:24 PM
Registered User
gatorlynch's Avatar

Undercarrige Bracket Help


I am looking for an "Undercarrige Bracket" - mine has developed cracking in 2 spots and is on it's last legs (no pun intended .....).

I was hoping one of you with a modified/custom undercarrige would have their stock piece unused and laying around, and would be able to throw it my way.

Please PM me if you can help - it wold be greatly appreciated !
Oct 12, 2012, 03:35 PM
Registered User
3171scott's Avatar
Quote:
Originally Posted by itsme2
I just went to Hobby King to order my motor, servos, ESC and BEC plus some other items.

The HS-82MG and HXT-900 servos recommended here are on back order. Can anyone recommend good alternatives from HK, I don't mind paying a little more?

Trying to do a quality build.

Thank you!
if you are going for quality go with HS 65mg on the ailerons and tail and HS65 on flaps.

If you like digital and dont like hightec's Futaba 3156 are sweet, a little priceie but sweet!
Oct 12, 2012, 05:54 PM
Registered User
bubbleman's Avatar
Quote:
Originally Posted by itsme2
I just went to Hobby King to order my motor, servos, ESC and BEC plus some other items.

The HS-82MG and HXT-900 servos recommended here are on back order. Can anyone recommend good alternatives from HK, I don't mind paying a little more?

Trying to do a quality build.

Thank you!
Here is what I ordered for my latest FC build:

Code Description Qty STATUS

G15-950 Turnigy G15 Brushless Outrunner 950kv 1 Reserved
TST-BEC45A TURNIGY TRUST 45A SBEC Brushless Speed Contr 1 Reserved
TST-SBECPG Turnigy Trust SBEC Programming Card 1 Reserved
HXT900 HXT900 9g / 1.6kg / .12sec Micro Servo 5 Reserved
SSV-9315 SSV 9315 Mabuchi 15.5g / 3.2kg / .15sec Serv 2 Reserved
APC11x5.5-E APC style propeller 11x5.5-E 2 Reserved
APC10x5-E APC style propeller 10x5-E 2 Reserved
APC12x6-E APC style propeller 12x6-E 2 Reserved
Z26503S-30 ZIPPY Flightmax 2650mAh 3S1P 30C 2 Reserved
601Ax5 Male XT60 connectors (5pcs/bag) GENUINE 1 Reserved
601Bx5 Female XT60 connectors (5pcs/bag) GENUINE 1 Reserved
OR002-01205 Alloy E-Prop Spinners AC378 5mm to 8mm 2 Reserved

The SSV-9315 are a tight fit but work for the rudder and elevator.

The power system will do 3 or 4 cell. The assortment of props allows for some experimenting.

On 4 cell with the 11x5.5 it is awesome

Anton
Oct 12, 2012, 06:25 PM
LcJ
LcJ
Forever TMWT Pilot #11
LcJ's Avatar
Quote:
Originally Posted by gatorlynch
I am looking for an "Undercarrige Bracket" - mine has developed cracking in 2 spots and is on it's last legs (no pun intended .....).

I was hoping one of you with a modified/custom undercarrige would have their stock piece unused and laying around, and would be able to throw it my way.

Please PM me if you can help - it wold be greatly appreciated !
Don't laugh.....well it is OK. Get some white seam binding tape. A sewing box would be a good place to look or the sewing aisle at wallyworld. Then cut it in a size to cover both sides of the cracks or wrap it is even better and then use thin CA and you have a light version of fiberglass tape. It will flex but probably will not break. You might also have to iron the folds out of the tape to get it flat enough to use. It is amazing what you can do with heavy duty thread and CA also.

Just ordered mine from Horizon (retirement gift certificates) and the motor, esc, prop, other misc from Heads Up Rc. Now if I ever get it built.
Latest blog entry: RC Logger's Eye One Xtreme Quad


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Fun Cub sinowace Hitec/Multiplex USA 14 Oct 09, 2011 04:43 PM
Discussion Multiplex Fun Jet at the lake bah7566 FPV Talk 31 Jan 03, 2010 09:19 AM
For Sale Multiplex Fun Jet -- PRICE DROP Toby W Aircraft - Electric - Airplanes (FS/W) 2 Dec 28, 2009 09:51 AM
Video Multiplex Fun Jet FPV set up test bah7566 Electric Plane Talk 0 Dec 25, 2009 10:05 PM
Wanted multiplex fun-jet or trade! heli123 Aircraft - Electric - Jets (FS/W) 0 Nov 14, 2009 11:02 AM