Shop our Airplanes Products Drone Products Sales
Feb 20, 2011, 06:24 PM
If it flys I can crash it!!!
scatcat1's Avatar
Shoe goo for sure, Gorilla glue is more brittle and is sort of hollow or porous when dry(it's a foaming glue)....good for depron/styro but no good for Elapor/EPO.
Sign up now
to remove ads between posts
Feb 20, 2011, 07:21 PM
PSALM 14:1
Sammy70's Avatar
Quote:
Originally Posted by aeroparts View Post
Hi FunCub fans.
This is our funcub built stock with original motor and prop. Full light equipped strobes landing light navlight etc.
3S 2500 as far as possible in the batt compartment.

GREAT paint scheme!
Feb 20, 2011, 08:02 PM
boat butcher
the goon's Avatar
Aeroparts,

Good looking fun cub . Is that what snow looks like

Mark
Feb 20, 2011, 11:23 PM
It's all up from here..
CuznWeakEyes's Avatar
Quote:
Originally Posted by mutha View Post
Recently while showing off inverted I reduced my first non UM foamie to a pile of white floaty bits, some of which blew away in the wind as I made that slow journey to scavenge any useful parts. **sigh** I really love this hobby

[snip]

Long story short questions ... should you use CA as stated by Multiplex and should it be with Kicker? Do you spray kicker on the (say) the motor mounts and then put the CA on the fuse or ??? What is the best way to use this stuff if you have to use it ...

remember I can't fail at this because she knows how much the FC cost!
Mutha....

The FunCub or any Multiplex model (AFAIK) will not be reduced to tiny bits of foam in a prang.....


Mine hit the pavement, nose first directly on the spinner and this is the result:



Here's a link to the post with the video...

https://www.rcgroups.com/forums/show...postcount=2453

...2 pieces.....2 big pieces! A little torquing of the crumpled edges, some regular Medium CA and reinforced with 3/4 oz. fiberglass cloth/CA and it is as good as new. BTW, I never used any kicker for the major assemblies.....only on some small parts I wanted to cure quickly. The only concern I had during building was gluing the fuselage sides together.....thought it might take too long and the glue would dry before I was ready....had my flying buddy (he's the one that pranged the FC...!!) help me spread it, we slapped it together and he held it while I adjusted any misalignment...mostly in the air intake on the cowl. We wrapped it with elastics and let it set for awhile.

And, I've been out of R/C for quite a while until 4 years ago.....who had ever heard of an electric helicopter!!! Boy, did I get hooked again....now into FPV and the FunCub is my first platform....it is outstanding for the many roles we might assign to it....

Cuzn
Feb 20, 2011, 11:24 PM
Charles Sherman
csherman's Avatar
Gorilla glue also comes in a clear format (at leats in my nexk of the woods) that doesn't expand and is just like ca but takes longer to dry.

Very good for when you need to make adjustments shortly after applying the glue.

Used it on the funcub - no problems.
Feb 20, 2011, 11:31 PM
Registered User
Prof100's Avatar
Quote:
Originally Posted by CuznWeakEyes View Post
Mutha....

The FunCub or any Multiplex model (AFAIK) will not be reduced to tiny bits of foam in a prang.....


Mine hit the pavement, nose first directly on the spinner and this is the result:



Here's a link to the post with the video...

https://www.rcgroups.com/forums/show...postcount=2453

...2 pieces.....2 big pieces! A little torquing of the crumpled edges, some regular Medium CA and reinforced with 3/4 oz. fiberglass cloth/CA and it is as good as new. BTW, I never used any kicker for the major assemblies.....only on some small parts I wanted to cure quickly. The only concern I had during building was gluing the fuselage sides together.....thought it might take too long and the glue would dry before I was ready....had my flying buddy (he's the one that pranged the FC...!!) help me spread it, we slapped it together and he held it while I adjusted any misalignment...mostly in the air intake on the cowl. We wrapped it with elastics and let it set for awhile.

And, I've been out of R/C for quite a while until 4 years ago.....who had ever heard of an electric helicopter!!! Boy, did I get hooked again....now into FPV and the FunCub is my first platform....it is outstanding for the many roles we might assign to it....

Cuzn
Cuzn,

I hate that when it happens, but the repair, like you said, was easy with a little medium CA and cloth.

Bill
Feb 21, 2011, 12:24 AM
Registered User
Van Leuven's Avatar
Quote:
Originally Posted by Prof100 View Post
Cuzn,

I hate that when it happens, but the repair, like you said, was easy with a little medium CA and cloth.

Bill
What kind of landing gear modification did you make? How about a picture of the bottom of your FC?
Feb 21, 2011, 03:31 AM
Good Better Best quest.
olmod's Avatar
I no longer use elastics to hold foam the grooves they leave dont come out easily, masking tape is better,even plastic wrap is handy.
Feb 21, 2011, 07:32 AM
Card Carrying Old Fart
Rickochet's Avatar
Quote:
Originally Posted by csherman View Post
Gorilla glue also comes in a clear format (at leats in my nexk of the woods) that doesn't expand and is just like ca but takes longer to dry.

Very good for when you need to make adjustments shortly after applying the glue.

Used it on the funcub - no problems.
Gorilla also has a CA "Super Glue". It is a medium CA that has micro rubber particles in it. I used it on my FC and it works very well. And it is available at most hardware stores, Lowes, Wally's etc. for those who don't have a LHS close.
Feb 21, 2011, 07:49 AM
Deplorable Patriot
SKYPILEIT's Avatar
Quote:
Originally Posted by aeroparts View Post
Hi FunCub fans.
This is our funcub built stock with original motor and prop. Full light equipped strobes landing light navlight etc.
3S 2500 as far as possible in the batt compartment.
Nice looking trim colors usedorange/white look good....battery is as far as possible..?

..forward.?..rearward.?Please explain.Thanks
Feb 21, 2011, 08:18 AM
Registered User
Prof100's Avatar
Quote:
Originally Posted by Van Leuven View Post
What kind of landing gear modification did you make? How about a picture of the bottom of your FC?
Here is a collage. I used hairbands, collars, allen head screws to create a nice suspension for the Funcub.
Feb 21, 2011, 09:14 AM
Registered User
Quote:
Originally Posted by Prof100 View Post
Use regular not Foam Safe CA on the FC. Kicker is your choice.
this one can be used?






I will start the build of mine with this one:


Feb 21, 2011, 09:18 AM
Registered User
Van Leuven's Avatar
Quote:
Originally Posted by Prof100 View Post
Here is a collage. I used hairbands, collars, allen head screws to create a nice suspension for the Funcub.
Thanks - I really like your set up!
Feb 21, 2011, 09:20 AM
Registered User
Van Leuven's Avatar
Quote:
Originally Posted by CuznWeakEyes View Post
Mutha....

The FunCub or any Multiplex model (AFAIK) will not be reduced to tiny bits of foam in a prang.....


Mine hit the pavement, nose first directly on the spinner and this is the result:



Here's a link to the post with the video...

https://www.rcgroups.com/forums/show...postcount=2453

...2 pieces.....2 big pieces! A little torquing of the crumpled edges, some regular Medium CA and reinforced with 3/4 oz. fiberglass cloth/CA and it is as good as new. BTW, I never used any kicker for the major assemblies.....only on some small parts I wanted to cure quickly. The only concern I had during building was gluing the fuselage sides together.....thought it might take too long and the glue would dry before I was ready....had my flying buddy (he's the one that pranged the FC...!!) help me spread it, we slapped it together and he held it while I adjusted any misalignment...mostly in the air intake on the cowl. We wrapped it with elastics and let it set for awhile.

And, I've been out of R/C for quite a while until 4 years ago.....who had ever heard of an electric helicopter!!! Boy, did I get hooked again....now into FPV and the FunCub is my first platform....it is outstanding for the many roles we might assign to it....

Cuzn
CuznWeakEyes - What landing gear are you using? I see a second wire on each side. Do you have another picture that shows your landing gear better? Thanks!
Feb 21, 2011, 09:47 AM
Card Carrying Old Fart
Rickochet's Avatar
Quote:
Originally Posted by xenupy View Post
this one can be used?






I will start the build of mine with this one:


Epoxy is not recommended on elapor, which is what the lower pic would seem to be. The top pic is CA type "Super Glue" but the viscosity is not shown. A "medium" CA is recommended. I am guessing a thin CA would tend to run quite a bit in areas that you don't want it. Check the "Important Notes" section, top of page 10 in the Fun Cub building instruction booklet.
Last edited by Rickochet; Feb 21, 2011 at 09:56 AM.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Fun Cub sinowace Hitec/Multiplex USA 14 Oct 09, 2011 04:43 PM
Discussion Multiplex Fun Jet at the lake bah7566 FPV Talk 31 Jan 03, 2010 09:19 AM
For Sale Multiplex Fun Jet -- PRICE DROP Toby W Aircraft - Electric - Airplanes (FS/W) 2 Dec 28, 2009 09:51 AM
Video Multiplex Fun Jet FPV set up test bah7566 Electric Plane Talk 0 Dec 25, 2009 10:05 PM
Wanted multiplex fun-jet or trade! heli123 Aircraft - Electric - Jets (FS/W) 0 Nov 14, 2009 11:02 AM