Thread Tools
Old Sep 17, 2012, 06:15 PM
queadlunnrau is offline
Find More Posts by queadlunnrau
Luck is my skill
queadlunnrau's Avatar
WOW this thread is HUGE!

Question if I have 31+ models, can I have all 30 internal memory slots full and can I access my other 1+ from the SD card? Or do I need at least 1 internal spot open and need to transfer the model from the SD card to internal memory?

BTW I did a search on SD card and models and came up with hundreds of posts, read though about 2 dozen before I decided to try and just ask.
Sign up now
to remove ads between posts
Old Sep 17, 2012, 06:29 PM
Buschbarber is offline
Find More Posts by Buschbarber
Registered User
Buschbarber's Avatar
Quote:
Originally Posted by queadlunnrau View Post
WOW this thread is HUGE!

Question if I have 31+ models, can I have all 30 internal memory slots full and can I access my other 1+ from the SD card? Or do I need at least 1 internal spot open and need to transfer the model from the SD card to internal memory?

BTW I did a search on SD card and models and came up with hundreds of posts, read though about 2 dozen before I decided to try and just ask.
If you Save your Model Memories to your SD card, you can Reset an existing Model Memory, set it up for a new aircraft, Save it to your SD card, and then Swap it back in when necessary. These may not be the correct terms, but you get the meaning.
Old Sep 17, 2012, 06:37 PM
bjaffee is offline
Find More Posts by bjaffee
Brett
bjaffee's Avatar
In other words, you cannot actually "run" a model off the sd card.
Old Sep 17, 2012, 06:39 PM
freechip is offline
Find More Posts by freechip
Surface, Air & Water Rc Toys..
freechip's Avatar
No, SD card is backup, Airware Updates & Telemetry logging.
Old Sep 17, 2012, 07:10 PM
queadlunnrau is offline
Find More Posts by queadlunnrau
Luck is my skill
queadlunnrau's Avatar
Thanks for all the quick replies.

Yeah my beloved DX7 is full now =( Time for a DX8.

There was a time when I thought 20 Models was a lot ... now even 30 models doen't seem like much.

I'm also assuming that any model copied from SD card would not have it's bind saved? Oh well it's not too much trouble to pull from memory into a saved open internal slot.
Old Sep 17, 2012, 07:18 PM
freechip is offline
Find More Posts by freechip
Surface, Air & Water Rc Toys..
freechip's Avatar
You are correct, once you IMPORT a model to any memory position you like a BIND would be required.

Basicaly model memory or the amount of models is sort of a second priority now with the ability to export and import to & from SD card.

It's now a matter of how many models the radio can hold BEFORE you have to rebind models from SD card.
Old Sep 17, 2012, 08:23 PM
bjaffee is offline
Find More Posts by bjaffee
Brett
bjaffee's Avatar
Quote:
Originally Posted by freechip View Post
You are correct, once you IMPORT a model to any memory position you like a BIND would be required.
.
I wonder if this would be true if you imported it to the same position it was at before? Reason I ask that is that when I was setting up my radio, I had programmed and bound one of my planes, then later accidently copied over that setup with one from another plane. The receiver was still bound to that model though. After I had finished programming the same model again, I did not have to rebind.
Old Sep 17, 2012, 08:40 PM
freechip is offline
Find More Posts by freechip
Surface, Air & Water Rc Toys..
freechip's Avatar
That's not the issue, the receiver is.

So if it's still the very same receiver and you import in the very same model position the yes it would work out the way you describe and you would not need to rebinb.

You would need to remember what memory it was.
Old Sep 17, 2012, 08:41 PM
AndyKunz is online now
Find More Posts by AndyKunz
AndyKunz's Avatar
Quote:
Originally Posted by bjaffee View Post
I wonder if this would be true if you imported it to the same position it was at before? Reason I ask that is that when I was setting up my radio, I had programmed and bound one of my planes, then later accidently copied over that setup with one from another plane. The receiver was still bound to that model though. After I had finished programming the same model again, I did not have to rebind.
On the DX7s and DX8, the bind would still be valid. On the current version of the DX10t and DX18 it would be lost, unless the model uses a low-speed DSM2 receiver (AR6100, etc.).

You are always best to re-bind after importing a model.

Andy
Site Sponsor
Old Sep 17, 2012, 09:40 PM
Franco2fly is offline
Find More Posts by Franco2fly
AMA 84248 since 1964
Thanks guys,
My problem came cuz the defaults were all take up, just needed to do an Inh on the aux channel to get geart to allow assignment.

KKKKFL
Old Sep 17, 2012, 10:10 PM
freechip is offline
Find More Posts by freechip
Surface, Air & Water Rc Toys..
freechip's Avatar
Quote:
Originally Posted by AndyKunz View Post
... You are always best to re-bind after importing a model. Andy
People don't always do what's best for them Andy, some fly into trees.
Old Sep 17, 2012, 10:15 PM
Mugen4Lfe is offline
Find More Posts by Mugen4Lfe
Registered User
Mugen4Lfe's Avatar
Quote:
Originally Posted by freechip View Post
People don't always do what's best for them Andy, some fly into trees.
Don't feel bad Andy, I had a light pole jump out at me before.
Old Sep 18, 2012, 06:36 AM
Franco2fly is offline
Find More Posts by Franco2fly
AMA 84248 since 1964
For any of you R/C'ers that use X-plane ( http://www.x-plane.org/ ) as a simulator, I just posted a rendition of my 1/4 Scale EAA biplane. If you stand at the end of the runway and fly with that view, it acts like the model. What I posted is the Full size aircraft, not the dimensions of the 1/4 scale since most of the XP users fly full size.

KKKKFL
Old Sep 18, 2012, 09:23 AM
AndyKunz is online now
Find More Posts by AndyKunz
AndyKunz's Avatar
Quote:
Originally Posted by Mugen4Lfe View Post
Don't feel bad Andy, I had a light pole jump out at me before.
I lost two planes to the SAME high-jump pole last winter, on the same night, making landing approaches! One was a Polecat so I guess it could be expected. And the P in P-51 stands for Pole, not Pursuit.

Andy
Site Sponsor
Old Sep 18, 2012, 10:51 AM
Mukenukem is offline
Find More Posts by Mukenukem
Registered User
Any obstacle nearby will be hit. That's a law
When flying in the gym, we also only hit the basketball baskets or the rings on the ceiling.

It's called obstacle-gravity. The smaller the obstacle, the larger the gravity. Like black holes.....


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Question Receivers that work with Spektrum Radios that are not made by Spektrum BD Flyer Radios 29 Sep 26, 2010 05:09 AM
Discussion Spektrum AR6100E or Spektrum AR6100? LaurenceGough Off-road Cars 23 Aug 06, 2009 06:33 AM
For Sale Parkzone 5ch DX10 w/Receiver ch54 CarlHill Aircraft - General - Radio Equipment (FS/W) 7 Jul 10, 2009 01:07 PM
Discussion Can I use a Spektrum Air RX with a Spektrum Surface TX? Bigmaxy Radios 1 Jan 19, 2008 08:57 PM
Sold GeForce 8400Gs PCIx DX10 video card GFBurke Non R/C Items (FS/W) 6 Sep 05, 2007 11:43 PM