Thread Tools
Old Aug 09, 2011, 08:33 PM
waynemia is offline
Find More Posts by waynemia
A trail of smoke is GOOD!
waynemia's Avatar
Would we R-E-A-L-L-Y miss it if they did not make PINK covering?
Sign up now
to remove ads between posts
Old Aug 09, 2011, 09:07 PM
DaOldGuy is offline
Find More Posts by DaOldGuy
Flying Half Pound and Down
DaOldGuy's Avatar
Quote:
Originally Posted by waynemia View Post
Would we R-E-A-L-L-Y miss it if they did not make PINK covering?
Yup.... The Heat does have lasting side affects.
Old Aug 09, 2011, 10:07 PM
waynemia is offline
Find More Posts by waynemia
A trail of smoke is GOOD!
waynemia's Avatar
Quote:
Originally Posted by DaOldGuy View Post
Yup.... The Heat does have lasting side affects.
Prolly Occasionally, I see a plane that looks a little interesting, then I see the PINK trim. I can't think of many things, although there are a few, the looks good with PINK trim.
Old Aug 10, 2011, 12:34 AM
David22 is offline
Find More Posts by David22
Suspended Account
Quote:
Originally Posted by waynemia View Post
Prolly Occasionally, I see a plane that looks a little interesting, then I see the PINK trim. I can't think of many things, although there are a few, the looks good with PINK trim.
Polka dots and a window to see the fuel tank.
Old Aug 10, 2011, 01:19 AM
3DNater is offline
Find More Posts by 3DNater
3d NOOBular
3DNater's Avatar
hey guys... I made some progress on my 51 AJ slick tonight. I'd post pics but I really just don't have the energy to take them, email them to myself from my phone, and then post them.

I got the gear on with wheel pants. The tail feathers are done. I ran into a hang up though because I need longer servo arms on the rudder and elevator. I just can't get the throw it needs. Currently I'm only getting about 22 degrees of up elevator and about the same on the rudder. Both of them need 45 degrees.

I got the rx in and esc sort of installed. Another snag is the motor mount. I got a pretty big motor and it has a wide footprint vs some that are longer for the same weight. This is causing it to use the next size up for motor mount so the pre-drilled holes with blind nuts installed aren't going to work. What a pain. As you might be able to tell I have lost all my energy for the night. The firewall needing extra attention seems to big of a pain to handle tonight so I think I'm just going to pack it in.
Old Aug 10, 2011, 02:57 AM
3DNater is offline
Find More Posts by 3DNater
3d NOOBular
3DNater's Avatar
well... I pulled on my bootstraps and got that motor mounted. It was easier than I thought it would be and the motor is all set up. Seems to spin up really nice. There is a little squeak right when it starts that is a little weird though.
Old Aug 10, 2011, 06:10 AM
DaOldGuy is offline
Find More Posts by DaOldGuy
Flying Half Pound and Down
DaOldGuy's Avatar
Quote:
Originally Posted by David22 View Post
Polka dots and a window to see the fuel tank.
Whoa... There has not been a "Dots" post in a Loooong time. I do like the clear window fuel gauge.

Quote:
Originally Posted by brathanke View Post
well... I pulled on my bootstraps and got that motor mounted. It was easier than I thought it would be and the motor is all set up. Seems to spin up really nice. There is a little squeak right when it starts that is a little weird though.
What motor are you installing Nate? Sounds like you may need a nap.
Old Aug 10, 2011, 06:44 AM
mt_flyer is offline
Find More Posts by mt_flyer
Montana Transplant
mt_flyer's Avatar
Quote:
Originally Posted by brathanke View Post
well... I pulled on my bootstraps and got that motor mounted. It was easier than I thought it would be and the motor is all set up. Seems to spin up really nice. There is a little squeak right when it starts that is a little weird though.
usually one of 3 things cause a "squeek"

bad bearing (doubtfull on new motor)
loose prop (your tired)
esc motor timing ( that may have 2 m's) timming
Old Aug 10, 2011, 06:46 AM
DaOldGuy is offline
Find More Posts by DaOldGuy
Flying Half Pound and Down
DaOldGuy's Avatar
Quote:
Originally Posted by mt_flyer View Post
usually one of 3 things cause a "squeek"

bad bearing (doubtfull on new motor)
loose prop (your tired)
esc motor timing ( that may have 2 m's) timming
I have seen them do that if the prop is a tad too much to start.
Old Aug 10, 2011, 06:49 AM
Outlw36 is offline
Find More Posts by Outlw36
Registered User
Morning Daniel.
Old Aug 10, 2011, 06:59 AM
Outlw36 is offline
Find More Posts by Outlw36
Registered User
Did a more thorough exam of the twist wreckage Saturday. Seems part of the problem was repair from the week before. Some thin CA had ran down the ventline and sucked up in the end of it it creating a 1/4 in plug. Also a small block of wood, I suspect a throttle brace, came loose and stuck in carb throat. I should've took a pic before I removed it. Wife was there at the time and said " I guess it's time to buy a new plane". Ordered it Sat afternoon and arrived on Tuesday lol. Slipstream 30cc sbach. Unfortunately work is interfering with assembly till the weekend.
Old Aug 10, 2011, 07:24 AM
mt_flyer is offline
Find More Posts by mt_flyer
Montana Transplant
mt_flyer's Avatar
Quote:
Originally Posted by Outlw36 View Post
Morning Daniel.
'morning Jim,
your up early on the left side....or up late... must be going to work...
i'm loading up to go fly... between rain drops
Old Aug 10, 2011, 07:26 AM
Outlw36 is offline
Find More Posts by Outlw36
Registered User
2hrs till end of shift lol.
Old Aug 10, 2011, 08:51 AM
kerwin50 is offline
Find More Posts by kerwin50
Registered User
kerwin50's Avatar
PINK You guys should of seen My plane barbie she was done in Neon pink. Talk about showing up in the sky.
Old Aug 10, 2011, 08:52 AM
kerwin50 is offline
Find More Posts by kerwin50
Registered User
kerwin50's Avatar
I believe this is color is closer to the NEON PINK


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Help! Tower SUper Saver Club la528it Hot Online Deals 55 Sep 16, 2016 05:53 PM
Discussion New Club Thread - Northern Beaches Soaring Club Psionic001 Australia 13 Sep 11, 2014 08:45 AM
Discussion San Francisco Model Yacht Club's multi-club Swap Meet craig_c Dock Talk 17 Oct 13, 2009 03:28 AM