Thread Tools
Jan 07, 2010, 06:48 AM
Registered User
Monza Red's Avatar
Discussion

Skis for Telemaster Electro


Hi Gang

We have a rare event in the UK, temperatures well below freezing and standing snow which is likely to stay for some time!

I'd like to fit skis to my 6ft (1.8 mtr) Telemaster.

What dimensions would you reccommend?

Happy Landings
Sign up now
to remove ads between posts
Jan 07, 2010, 07:29 AM
jrb
jrb
Member
jrb's Avatar
The two smaller set are from here ( http://www.maidenusammp.com/ ) -- the blue gear fits the H9 Toledo Special

H9 Toledo Special T/O off Snow (0 min 14 sec)


H9 Toledo Special Full Throttle Pass (0 min 11 sec)


H9 Toledo Special Landing On Snow (0 min 21 sec)


RC J-3 CUBS FLY IN SNOW (2 min 22 sec)
Jan 07, 2010, 08:23 AM
One cell short of a Pack
steve1814's Avatar
These Work Great on my Electro Telemaster. They are pretty robust too.

HTH,
Steve
Jan 07, 2010, 09:03 AM
jrb
jrb
Member
jrb's Avatar
YMMV especially w/snow conditions; but I found that the middle sized set of skis were too small for my 1/4 Cub, but just right fo 1/5 Cub & Toledo Special.

That's why I got a set of the larger skis for my 1/4 Cub juts like to ones used on my flying buds 1/4 Cub -- there's are gas mine E.

This is especially true with fresh fluffy snow (even added tail wheel ski); not so with heavy wet packed snow -- ice >>> bigger still works too.
Jan 08, 2010, 10:54 AM
Sussex, UK
RobinBennett's Avatar
I've been tempted to do the same, for a 60" plane.

It looks like the skis are about the same length as the wing chord, and about 1/6th as wide? How big does the curve at the front need to be?

Is there anything to hold the skis at the right angle? I'd worry about them being knocked or vibrating until the front points downwards enough to dig in on landing.
Jan 08, 2010, 11:45 AM
Registered User
Quote:
Originally Posted by RobinBennett View Post
I've been tempted to do the same, for a 60" plane.

It looks like the skis are about the same length as the wing chord, and about 1/6th as wide? How big does the curve at the front need to be?

Is there anything to hold the skis at the right angle? I'd worry about them being knocked or vibrating until the front points downwards enough to dig in on landing.
I have the Maiden skis on my Multiplex Mentor, and they work great. The skis are connected to the axle with two set screws that will prevent a change in angle when tightened properly.

I will also put in a good word about the company, the support is excellent.
Jan 08, 2010, 12:02 PM
jrb
jrb
Member
jrb's Avatar
Maiden website from above posting: are from here ( http://www.maidenusammp.com/ ) .

A lot of good info on the site too.

This is from Dubro site:
Jan 10, 2010, 05:57 AM
Sussex, UK
RobinBennett's Avatar
Monza, here's a picture of some I made yesterday and tested today. They were 12" long and 2" wide, the curve on the front was made around a 6" paint tin, bent to about 45 degrees.

I used 2mm polycarbonate, with a second layer 6" long in the middle to spread the load. The attachments were just blocks of wood that were drilled to be a tight fit on the standard axles. The weight of the plane would rotate the skis between 'tail up' and 'tail down' but they didn't move in flight.

Videos here
https://www.rcgroups.com/forums/show...7#post14030587

Jan 10, 2010, 02:19 PM
Registered User
Bill Glover's Avatar
Nice! I've used skis on various IC models in the past, but never on any of the electrics I have now.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Telemaster Electro Assemble and Fly for AP DWA Aerial Photography 589 Dec 11, 2009 09:13 PM
Discussion Getting near time to fly skis, Mov SS on skis steve ypsi mi GWS (Grand Wing Servo) 3 Oct 14, 2009 09:01 PM
Discussion Yet another Electro Telemaster AP ship Canada Goose Aerial Photography 7 Sep 28, 2009 02:18 PM
Discussion Mini Telemaster on skis pointerfarm Sport Planes 1 Jan 14, 2008 11:31 AM
Sold 6' Telemaster Electro for sale bh95 Aircraft - Electric - Airplanes (FS/W) 4 Aug 21, 2006 03:01 PM