Flyfly mig 29 OVT ak MIG 35 - RC Groups
Shop our Airplanes Products Drone Products Sales
Thread Tools
Jan 01, 2010, 07:03 AM
Registered User

Flyfly mig 29 OVT ak MIG 35

Hi all

I am building a fly fly MIG 29 OVT and a lot af changes are needed to get this all to work.

The setup
1 x Flyfly MIG 29
2 x Wemotec midi fans
2 x 90mm RC lander TV's
2 x Turnigy B36-56-06 1800kv Inrunner
2 x Turnigy Plush 80A w/ UBEC Speed Controller
8 x HS-82MG servos
2 x 3S1P 5000 mAh Flight Max 30C
1 x AR7000
1 x on-board mixer for trust vectoring ( home made )

I started with the Tailrons, I made them a little bit stronger :-)

Sign up now
to remove ads between posts
Jan 01, 2010, 07:08 AM
Registered User
Home made Wing servo mounts

Servo is glued to the cover.

big ailerons : the mig won't be a racer but a 3D EDF

Jan 01, 2010, 07:19 AM
Registered User
When I tried everything out to get the Center of gravity correct. found out that the lipo had to go in to he nose.

After change the nose, so that the lipo will fit into it
Jan 01, 2010, 07:31 AM
Registered User
No I am try to get al the electronics in place and make sure tha every thing will work.

White are 8 servo's
Yellow are the two EDF's
Green the speed controllers
Pink AR7000 receiver
Red power Lipo

The question is what do I need to do to get this al working without any
problems. Because all servo wires are running beside the motor wires.

- ferrite coiling on the receiver side for all servo wires ?
- Twist motor wires, Do I need to twist or braiding ( don't no if this is the
correct name but I mean the take the outside wire en cross it over the middle wire ) ?
- something else ?

I never had a configuration like this and I hope to do it the first time wright.

Jan 01, 2010, 09:19 AM
Registered User
With 2.4 I do not think you'll have any problems.
Jan 01, 2010, 01:46 PM
Registered User
M.Huerta's Avatar
Originally Posted by Chris True
With 2.4 I do not think you'll have any problems.
+1, only on 72 might you have problems
Jan 10, 2010, 03:28 PM
Registered User



Jan 26, 2010, 03:09 AM


Hi Bart, Im also in proces building twin Mig, using Vemotecs/ARC/80amp,my will run on 2 six cell 4-5000 packs. I will use fixed l/gear to keep it simple also will install smaller Ail. Do you have intention to reduce those huge rear outlets?? Joe, Banana Coast/Aust.
Mar 31, 2010, 09:43 AM
Registered User
mikecopey's Avatar
Nice project !!!
any updates ?
Hoping you gave it a custom paint job.....
Aug 24, 2010, 11:41 PM
Registered User
Aug 26, 2010, 04:22 AM
Bart, hows the 3D Mig29 going ? Love to hear to share some experience, Joe.
Oct 28, 2010, 01:22 PM
Jet Foamy addict
Any new pictures, i just picked up the RC-Lander version which has many updates to the frame


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Idea 18" WS Mig 29 and F-35 with plans - updated Fisticuffs! Pusher Prop Jet Models 44 Aug 26, 2011 08:36 AM
Discussion HET Mig-29 Vs FlyFly Mig 29 skydve76 Electric Ducted Fan Jet Talk 2 Oct 06, 2008 01:32 PM
Discussion P-180 powered Mig-29 OVT likai Jet Turbines 1 Jul 27, 2008 08:29 PM
Discussion Mig-29 OVT powered by single P-180 likai Fuel Jet Talk 0 Jul 17, 2008 10:45 AM
New Product Finally FlyFly Mig 29 will be available schumnig Foamy EDFs 18 Apr 29, 2008 08:33 PM