Settings for a DX6i for a Skyartec Wasp 3
Anyone using a Skyartec Wasp 3 with a DX6i & AR6000? What are your setting?
Check this Skyartec Wasp 3 with a DX6i:
Last edited by rhong; Dec 28, 2009 at 11:22 PM. Reason: found the answer
Blue to A on ESC
Red to C on ESC
Yellow to B on ESC
To reset the ESC for the Throttle of your new receiver:
Connect your channel 3 of the receiver to the plug on the ESC
With the throttle at lowest setting plug in the battery to the ESC
The ESC should beep and then play a short tune; if the ESC beeps
contentiously for longer then 30 seconds follow the instructions below.
Sometimes when connecting a new ESC to a receiver,
we must reset the ESC so it knows the top end and bottom end
of the throttle control.
These steps are easy.
Leave the throttle trim tab at bottom like you normally use it.
Throttle range setting:
1. Switch on transmitter, move throttle stick to top
2. Connect battery pack to ESC, and wait for about 2 seconds
"Beep-Beep-" tone should be emitted, means throttle range highest point has been correctly confirmed
3. Move throttle stick to the bottom, several "beep-" tones should be emitted, presenting the number of battery cells
A long "Beep-" tone should be emitted, means throttle range lowest point has been correctly confirmed
4. You should be ready to test fly.
Hope this helps
Just a few extra things to consider:
- make sure your throttle curve is set to 100% at full stick before doing the above
- similarly, make sure your curve is set to 0% at bottom stick. Also since you're on a DX6i now, beware that if in the future you initialise the heli with throttle hold on, it will spool up when you flick it off if you haven't set your curves to match.
- The ESCs used by the Wasp seem to follow a similar configuration strategy to typical turnigy/other ESCs. After playing a funky tune, the ESCs will rattle out a series of beep codes spaced evenly apart, each sequence of beeps referring to the current setting of that particular configuration (i.e. soft start if it exists, motor timing, etc). While you don't have to care about this, if you ever want to change that configuration, you can access it by raising the throttle as above, waiting for the sequence you're interested in, then dropping the throttle... well, you get the idea. pop online for a list decoding all those beeps.
I use a DX6i with my Wasp v3 and an AR6110e. One of the first changes I made! Do keep a very close eye on the binding that happens with the head though, as the servos center differently and have a much bigger range on a Spektrum radio, compared to Skyartec's. You'll need to remove all the servo arms and reseat them, most likely.
On my radio:
AILE 0 75% 1 100%
ELEV 0 75% 1 100%
RUDD 0 48% 1 100%
Everything 100% after servo horns adjusted
Throttle Curve for 7.4v (don't do 3D myself):
Swash mix (this is where I've accomodated for the extra servo travel, allowing for big cyclic but smaller pitch adjustments):
Swash type: CCPM 120 deg
And that's what I use
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|Discussion||New Skyartec Wasp 3 no longer binds with the transmitter||rhong||Skyartec||9||Jan 24, 2010 01:58 PM|
|Discussion||Skyartec Wasp V4 Belt 250 3D 6 channel RC helicopter||Beemer444||Micro Helis||9||Dec 25, 2009 03:14 AM|
|Sold||Skyartec Wasp V3 CP RTF CHEAP and Good to Fly!||mygsx||Aircraft - Electric - Helis (FS/W)||8||Nov 19, 2009 04:44 AM|
|For Sale||SkyArtec Wasp V4 200 Helicopter - NIB - RTF!||ptt81||Aircraft - Electric - Helis (FS/W)||0||Oct 23, 2009 04:51 PM|
|Discussion||New Skyartec Wasp 3 does not bind||rhong||Beginner Training Area (Heli-Electric)||1||Oct 01, 2009 02:01 PM|