View Poll Results: If you are reading this thread are you an IOM owner
Yes 26 49.06%
No 27 50.94%
Voters: 53. You may not vote on this poll

Thread Tools
Mar 06, 2012, 04:33 PM
Registered User
ToniGe23's Avatar
MYA IOM Ranking Bartley Green SC 4th March 2012 (8 min 5 sec)
Last edited by ToniGe23; Mar 07, 2012 at 06:18 PM.
Sign up now
to remove ads between posts
Mar 09, 2012, 10:23 AM
Registered User
max67's Avatar
Hi all

Sabaudia, National Regatta Modelvela Class 1 Meter
Sabaudia - The Modelvela Italy in collaboration with the Sailing Club The Sirens and the City Department of Sabaudia organized system at the Sports Center of Sabaudia Navy Rowing Regatta National radio controlled sail boats in Class 1 meter 17 and 18 in March.
About the Site: http://iomcentroitalia.altervista.org and http://www.modelvela.it
Sabaudia and the Sport Center Rowing Navy will host the 7 - 8 - 9 September, the Italian Championship in 2012 Italy Modelvela Class 1 meter.
For further information please contact the Executive Officer Zone IV Modelvela for IVF.
Marco Di Giuseppe
marco.digiuseppe @ hotmail.it
Mar 11, 2012, 07:11 PM
Registered User
My son and I sailed our Britpops for the first time today, not only are they beautifully built they sail really nice. It was just a practice day so no scores to talk about.

The part we both really liked was the boats ability to follow the wind shifts with little or no rudder required. Winds were mostly around 10 with a few puffs near 15.

More as we get into the racing season in a few weeks....bye for now gotta go polish my boat.

Ted
Mar 12, 2012, 02:40 AM
Registered User
ToniGe23's Avatar
Hi Ted,
Some pictures would be nice, who built them?
Mar 12, 2012, 08:08 AM
Registered User
Robot Yachts, James Edwards, built the boats. I don't have any good pictures yet, they look exactly like the blue boat Brad sailed last year except they aren't blue.

Ted
Mar 14, 2012, 07:20 AM
Registered User
8387mike's Avatar
Ops i have done it again, another boat on its way from the UK
Mar 14, 2012, 12:52 PM
Registered User

V-7 drain hole


Where do i put a drain hole on my V-7? Right now it does not leak but it probably will.

I am very satisfied with the boat. it is very forgiving and fast. It makes up for my mistakes and comes from behind nicely. It points high and carries the #1 rig much better than I expected in the top wind range.

ron
Mar 15, 2012, 02:54 AM
Flying without a licence
FWAL's Avatar
Quote:
Originally Posted by 8387mike View Post
Ops i have done it again, another boat on its way from the UK
Any clues as to which IOM is taking your fancy ?
Mar 15, 2012, 03:39 AM
Registered User
ToniGe23's Avatar
Hi Ron,
If you drill a hole in the sten end (transom) you may not be able to use a bung as it could make it over length so you would have to use a patch just something to consider
Mar 15, 2012, 03:40 AM
Registered User
ToniGe23's Avatar
Quote:
Originally Posted by FWAL View Post
Any clues as to which IOM is taking your fancy ?
I'm betting it could be a brother to his lunatic!
Mar 15, 2012, 03:48 AM
Registered User
Has anyone seen the Brit Pops from the other builders.
Mar 15, 2012, 07:01 AM
Registered User
Quote:
Originally Posted by ron locke View Post
Where do i put a drain hole on my V-7? Right now it does not leak but it probably will.

I am very satisfied with the boat. it is very forgiving and fast. It makes up for my mistakes and comes from behind nicely. It points high and carries the #1 rig much better than I expected in the top wind range.

ron
V7 is similar to the TS2 at the stern very shallow deck to hull for the plug,put the plug on deck right behind the bow bumper,it's easy to hold the boat down by the dull side of the keel and won't snag on anything up there,plus you can see it when you've forgotten to put it in.
Mar 15, 2012, 09:17 AM
Registered User
Tug-

Eric Arndt, aka Houdini 13, stopped by quickly last weekend with his hot-off-the-press britpop hull #2 from Pepe in Spain for its 1st splash and it was a beautiful white molding. Vinaixa Yachts look to be extremely well crafted. I have heard that he is the only builder of britpops that is using custom, cnc'ed aluminum molds. Ron Locke's V7, also from Pepe is beautiful as well!
sully
Mar 15, 2012, 11:31 AM
Registered User
ToniGe23's Avatar
I'm sure there all using CNC machined molds supplied by Brad http://www.robotyachts.co.uk/britpop.html Dennis Astbury Yachts also are one of the best around at moulding boats that's why Brad chose these builders for his design.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion X-3D Brushless Quadrocopter, general quadrocopter, x-ufo discussion tend2it Multirotor Drone Talk 2529 Apr 26, 2008 07:45 PM
Discussion Kong Power Packs Info And General Discussion nitroshark Batteries and Chargers 10 Jan 12, 2008 11:33 PM
Discussion Kong Power Packs Info And General Discussion nitroshark Batteries and Chargers 32 Jan 03, 2008 03:02 PM
Discussion General Discussion Inflexo Australia 172 Nov 27, 2006 10:26 PM
General Discussion / Training Area zax Site Chat 0 Oct 03, 2001 01:48 PM