Thread Tools
Old Nov 26, 2012, 09:41 PM
cale10 is online now
Find More Posts by cale10
AMA Another Mans Airplane
cale10's Avatar
hey guys the nine eagles micro yak 54 is only 27$ usa warehouse!RTF
Sign up now
to remove ads between posts
Old Nov 27, 2012, 04:16 AM
Andy2No is offline
Find More Posts by Andy2No
NaN
Andy2No's Avatar
Quote:
Originally Posted by joker24458 View Post
Ok, ya, this hot wire cutter is a bit more complicated than I thought.....plus it would take up a model memory on my transmitter.
No need for a model memory, just use a cheap servo tester, like this, to control the ESC:

http://www.hobbyking.com/hobbyking/s...vo_Tester.html

If you use a 12V power supply, make sure it can deliver a few amps. You don't really need that many volts though, unless you're trying to make a big cutter. For something small, just three of four rechargeable AAs would do - or the minimum number the ESC will work with.
Old Nov 27, 2012, 06:05 PM
pmpjohn is offline
Find More Posts by pmpjohn
Dr John
pmpjohn's Avatar
Here are a couple of pics of the new smaller, lighter Mig29 twin 28mm EDF. My original 18"ws bird came out at 180grs. To shed some weight I scaled her down to 15" ws, changed a lot of 6mm Depron to 3mm and came in at 147grs. It could be built even lighter by leaving off the carbon fiber leading edge protectors, the fiberglass wing and top covering that would also save a few coats of WBPU. If the wind stays down I will try for a maiden in the morning.

Dr John
Old Nov 28, 2012, 11:59 AM
seitz2c is offline
Find More Posts by seitz2c
P. Seitz
Looks fast just setting there! Good luck on the maiden .

Paul
Old Nov 28, 2012, 12:25 PM
pmpjohn is offline
Find More Posts by pmpjohn
Dr John
pmpjohn's Avatar
Maiden was a complete nonevent. Gentle toss into the wind and away she went. Once on step she took a couple clicks of down and was flying hands off. She is noticably faster than the Mig-15 UMX. Very responsive to control input, roll rate on the border of to fast! The sound of those two 28mm fans blowing by 10 foot out and at eye level must be heard to be fully appreciated. I was using an rcbabbel 500mah 2s Hyperion pack and on the maiden at 2.5 mins only used 240mah. For the next flight I set the timer to 4min and still had punch while on final. Next time out I will try to get some video.

Dr John
Old Nov 28, 2012, 12:49 PM
BryanEW710 is offline
Find More Posts by BryanEW710
Registered User
BryanEW710's Avatar
Love to see video
Old Nov 28, 2012, 09:37 PM
Capt.RJM is offline
Find More Posts by Capt.RJM
Registered User

Sig 20 inch 1929'er model


Attached are the .jpg's of my just completed 29'er Sig. kit with ar6400 radio and motor from a P-51. The wing span is 20.5 inches and comes in at 47 grams with battery installed. Always enjoyed working with balsa and tissue. Now I wait for a no wind day for the maiden.
Capt.RJM
Sandusky,Ohio



Old Nov 28, 2012, 09:39 PM
coriolan is offline
Find More Posts by coriolan
"Unnecessary Necessity"
coriolan's Avatar
Looking good Capt.RJM
Old Nov 28, 2012, 10:17 PM
seitz2c is offline
Find More Posts by seitz2c
P. Seitz
I was flying with Paul McILRATH just last week he still flies rubber every Sunday afternoon I know he will like the conversion. I'll show him your photos


Paul
Old Nov 29, 2012, 12:44 AM
pookielips1954 is offline
Find More Posts by pookielips1954
Registered User
Here's a couple of mine. First is a 1/32 sheet balsa clone of a 1950s rubber powered 18" Carl Goldberg Shoestring. AR6400, P-51 motor and prop, 150 mah battery. RTF weight 1.35 ounces. Great little indoor flyer! Russ Farris
Last edited by pookielips1954; Nov 29, 2012 at 01:02 AM.
Old Nov 29, 2012, 12:48 AM
pookielips1954 is offline
Find More Posts by pookielips1954
Registered User
Here's the second - 1/32 sheet balsa clone of Carl Goldberg Cessna 180 circa 1957. 20" span 1.25 ounces. Same setup as the Shoestring. Another excellent flyer! These models were downloaded for free from Paul Bradleys excellent website linked below. Russ Farris

http://www.parmodels.com/index.htm
Last edited by pookielips1954; Nov 29, 2012 at 12:56 AM.
Old Nov 29, 2012, 08:56 AM
addictedtoplanes is offline
Find More Posts by addictedtoplanes
GaperBait
addictedtoplanes's Avatar
Quote:
Originally Posted by Capt.RJM View Post
Attached are the .jpg's of my just completed 29'er Sig. kit with ar6400 radio and motor from a P-51. The wing span is 20.5 inches and comes in at 47 grams with battery installed. Always enjoyed working with balsa and tissue. Now I wait for a no wind day for the maiden.
Capt.RJM
Sandusky,Ohio



Sweet, I just built their tiger from the same series. It flies amazingly. It's slow and stable and can loop. Mine is the same size as yours and about the same weight. I'll post pics soon. Good luck with your maiden!
Old Nov 29, 2012, 12:48 PM
Capt.RJM is offline
Find More Posts by Capt.RJM
Registered User
addictedtoplanes....

Still waiting for the winds to die down for my maiden flight. What power unit did you install for your tiger from Sig.

Capt.RJM
Old Nov 29, 2012, 04:10 PM
addictedtoplanes is offline
Find More Posts by addictedtoplanes
GaperBait
addictedtoplanes's Avatar
the um p-51 motor and gearbox, and the ar6400
Old Nov 30, 2012, 08:26 AM
TedD60 is offline
Find More Posts by TedD60
Registered User
Quote:
Originally Posted by addictedtoplanes View Post
the um p-51 motor and gearbox, and the ar6400
... speaking of which ... CHRISTMAS IS COMING!!!

and many of us are on a pretty tight budget.

Where can the best deals be found on um P51 Motors and gear boxes, AR6400 receivers and transmitters that work with the ar6400?

Thanks


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Pictures: When planes were able to show off, at air shows Patrick Plawner Life, The Universe, and Politics 172 Dec 10, 2014 05:31 PM
Cool Show off your Parkzone Micro P-51!!! P-51C Scratchbuilt Indoor and Micro Models 938 Nov 20, 2012 07:49 PM
Discussion Show us those planes you really need to replace! JimTMich Parkflyers 8 Apr 26, 2012 12:05 PM
Discussion Show off those home made camera gimbals! ben1101 Aerial Photography 2 Jul 22, 2009 08:11 PM