Thread Tools
Old Aug 25, 2010, 11:42 PM
thanhTran is offline
Find More Posts by thanhTran
That tree again!!!!
thanhTran's Avatar
Quote:
Originally Posted by Fulg View Post
...

What could cause this discrepancy? Is it normal?
All Atmel chips are not having the same frequency even you set it at 8Mhz. The frequency varies a little from chip to chip so it makes sense that in some boards you have to change the trim.
Last edited by thanhTran; Aug 25, 2010 at 11:59 PM.
Sign up now
to remove ads between posts
Old Aug 25, 2010, 11:44 PM
Fulg is offline
Find More Posts by Fulg
Registered User
Fulg's Avatar
Quote:
Originally Posted by thanhTran View Post
The ESC can only store one throttle range, so if you set from the controller it wipes out whatever you set earlier.
Yeah. I was trying to point out was that setting the throttle range through the controller makes sure all four ESCs are programmed identically. For some reason, the resulting throttle range was slightly different when I set them up separately.
Old Aug 25, 2010, 11:48 PM
Fulg is offline
Find More Posts by Fulg
Registered User
Fulg's Avatar
Quote:
Originally Posted by thanhTran View Post
All Atmel chips are not having the same frequency even you set it at 8Mhz. The frequency varies a little from chip to chip so it makes sense that in some boards you have to changes the trim.
Right, that makes perfect sense... thanks for clearing that up! I can start trusting the board to my future tricopter now...

Cheers,
Ben.
Old Aug 26, 2010, 12:04 AM
spagoziak is offline
Find More Posts by spagoziak
"Let's put a camera on that.."
spagoziak's Avatar

Where do I find these little guys?


Hi folks,

Instead of soldering wires directly to the board, I'd like to put pins in for the channels.

Does anyone know where I can get these things? My LHS didn't have them, and neither did radio shack.

Thanks!
spag
Old Aug 26, 2010, 12:06 AM
thanhTran is offline
Find More Posts by thanhTran
That tree again!!!!
thanhTran's Avatar
Quote:
Originally Posted by Fulg View Post
...For some reason, the resulting throttle range was slightly different when I set them up separately.
I've seen that too. I think the same frequency issue causes that. Because of the different frequency, some chips don't calculate the neutral points of the aileron, elevator, and yaw correctly. So this adds into the control and causes some motor to run faster than other. I've posted some logic analyzer screen shots in this thread and you could see the pulses are not the same.
Old Aug 26, 2010, 12:08 AM
thanhTran is offline
Find More Posts by thanhTran
That tree again!!!!
thanhTran's Avatar
Quote:
Originally Posted by spagoziak View Post
Hi folks,
Does anyone know where I can get these things? My LHS didn't have them, and neither did radio shack.

Thanks!
spag
From your neighbor Digikey

http://search.digikey.com/scripts/Dk...9400E-01-36-ND

Sparkfun also has some.
Old Aug 26, 2010, 12:14 AM
DarkHeli is offline
Find More Posts by DarkHeli
Future-proof EVERYTHING
DarkHeli's Avatar
Quote:
Originally Posted by Fulg View Post
Congrats. Feels good, doesn't it

Are you using all CCW props? If so, you may not have angled your front/back motors enough (or too much). Popular angles are between 5 and 10 degrees clockwise (with the arm towards you), I presume it varies based on your prop size and motor strength. I had to experiment a bit with the angles before getting a non-yawing quad at 50% gain.

If you're using mixed CW/CCW props, then I have no idea.

Ben.
Using all ccw for the time being. I will mess with the angles some more.

Thanks.
Old Aug 26, 2010, 12:36 AM
bob4432 is offline
Find More Posts by bob4432
Registered User
bob4432's Avatar
Quote:
Originally Posted by spagoziak View Post
Hi folks,

Instead of soldering wires directly to the board, I'd like to put pins in for the channels.

Does anyone know where I can get these things? My LHS didn't have them, and neither did radio shack.

Thanks!
spag
how are you going to connect the rx? i thought about the same thing but i can't find any female-female extensions to go from the rx to the board, unless i have just missed them...

mouser has them too - http://www.mouser.com/Search/Product...538-22-28-4125 these are 12 count units, so you may as well order quite a few - i am not sure how digi-key's shipping is but mouser's is ~$7 for the first pound - may want to add other items along w/ it.
Old Aug 26, 2010, 12:52 AM
Jakub J is offline
Find More Posts by Jakub J
Jakub J's Avatar
Quote:
Originally Posted by kapteinkuk View Post
Jakub, will you send me your free subscrition small frame soon?
Hi

No - I'll send it with new tri, and maybe other this week

Jakub
Site Sponsor
Old Aug 26, 2010, 12:55 AM
don_cocinero is offline
Find More Posts by don_cocinero
Tinkerer
don_cocinero's Avatar
Quote:
Originally Posted by bob4432 View Post
how are you going to connect the rx? i thought about the same thing but i can't find any female-female extensions to go from the rx to the board, unless i have just missed them...
You can find those here

BTW - off topic - handy flight time calculator here.
Old Aug 26, 2010, 01:08 AM
spagoziak is offline
Find More Posts by spagoziak
"Let's put a camera on that.."
spagoziak's Avatar
Hi again! I'd like to use a switch to control power from the battery. I plan on using 3S lipos, 20C to 30C. The speed controllers are Turnigy Plush 25A. Is this switch an appropriate choice?

http://search.digikey.com/scripts/Dk...ame=67-1934-ND
Old Aug 26, 2010, 01:10 AM
spagoziak is offline
Find More Posts by spagoziak
"Let's put a camera on that.."
spagoziak's Avatar
Contact a member here named BD Flyer--he makes JST cables any way you want them. He does it crazy cheap and sends them out darn near before you realize you wanted them. They're awesome

Quote:
Originally Posted by bob4432 View Post
how are you going to connect the rx? i thought about the same thing but i can't find any female-female extensions to go from the rx to the board, unless i have just missed them...

mouser has them too - http://www.mouser.com/Search/Product...538-22-28-4125 these are 12 count units, so you may as well order quite a few - i am not sure how digi-key's shipping is but mouser's is ~$7 for the first pound - may want to add other items along w/ it.
Old Aug 26, 2010, 01:26 AM
bob4432 is offline
Find More Posts by bob4432
Registered User
bob4432's Avatar
well, no longer a quad virgin took it out this evening -~8:45 - wind was ~10-15MPH and would come from all directions - is that enough wind to move it around? it stayed flat, but @ ~8' got moved around a bit more than i would have liked. also seemed a bit sluggish/loose if that makes sense.

running quad firmware 4.5, atv 50% roll, 50% pitch and 100% yaw, quad is 1048g, ~25" motor to motor center. pots all @ ~50%. would say i never used more than 1/2 throttle or if i did it was for a very short amount of time.

always came down on the landing gear so i am calling the first flight of it and me a success no flips or anything and it is more stable 2' above the ground compared to 3-4" couldn't get it trimmed due to the wind constantly changing directions.

hoping this weekend the school i flew @ will be vacant and i can fly in the daytime on one of the fields and not lose front arm orientation

no video due to lack of light
Last edited by bob4432; Aug 26, 2010 at 01:48 AM.
Old Aug 26, 2010, 01:53 AM
alll is offline
Find More Posts by alll
manuLRK
manuLRK
Last edited by alll; Aug 26, 2010 at 02:03 AM.
Old Aug 26, 2010, 02:00 AM
thanhTran is offline
Find More Posts by thanhTran
That tree again!!!!
thanhTran's Avatar
Quote:
Originally Posted by bob4432 View Post
well, no longer a quad virgin
Awesome! Congratulation Yeah, in wind, the quad can be quite slow and does seem like it's not responding to your command.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Quadrotor brushless controller airbotix Multirotor Talk 63 Aug 06, 2010 12:15 PM
Discussion ALPO -Aerobatic Low Parts count Original design. Brian Courtice Foamies (Scratchbuilt) 8 Sep 21, 2009 04:57 AM
Discussion Any tips for my first flight with a low wing plane? Warthog_Fan Fuel Plane Talk 4 Sep 06, 2009 08:53 AM
Help! Need help with Low-cost QuadRotor Hero.sl Coaxial Helicopters 5 Jun 28, 2009 03:26 AM
Question Searching Simple Controller for Free Flight flymax Power Systems 8 Jan 07, 2006 11:07 AM