Thread Tools
Jan 18, 2010, 07:33 AM
Registered User
rimshotcopter's Avatar
Quote:
Originally Posted by etman
My first maiden outdoor flight!

Video uploading soon.
http://www.vimeo.com/8807891
Great Job and an Awesome build. I also love the bumper design, should be great for indoor flight too.

thank you so very much for sharing this video with us, it is greatly appreciated.
Sign up now
to remove ads between posts
Jan 18, 2010, 07:52 AM
Flying with the eagles
etman's Avatar
Quote:
Originally Posted by AC5FF
etman - great job!!! Looks like it's flying pretty darn good for ya! I love the look of your 'bumpers' around the edges! A hulahoop eh?? Awesome idea!!! You'll have to get it up in the air and then give it full rudder - see if you can the hula-hoop effect going on vid. LoL

Thx for your input on my gain question.... Will try to get out again tomorrow and give that a try
Thanks AC5FF and RR!

When I bought a red hulahoop my little boy liked it so much and played with it.
Haha...I had to sneakily cut it into three pieces when he was not around.
After that I bought another one for him.
Jan 18, 2010, 07:57 AM
Registered User
rimshotcopter's Avatar
Quote:
Originally Posted by etman
Thanks AC5FF and RR!

When I bought a red hulahoop my little boy liked it so much and played with it.
Haha...I had to sneakily cut it into three pieces when he was not around.
After that I bought another one for him.

Bad ETMan, Bad. LOL

I hope you purchased the kid a new and better one.
Jan 18, 2010, 08:00 AM
Flying with the eagles
etman's Avatar
Quote:
Originally Posted by reverendrichie
Bad ETMan, Bad. LOL

I hope you purchased the kid a new and better one.
Heheheh....(evil laugh)
Jan 18, 2010, 09:52 AM
Registered User
TexasPete's Avatar
Quote:
Originally Posted by Pepelatz
Pepelatz,
I stand corrected. Would you happen to know the model and Availability of the motor used? Bet it would make an exceptional tricopter motor!
Texas Pete
Jan 18, 2010, 10:20 AM
Flying with the eagles
etman's Avatar
Quote:
Originally Posted by etman
My first maiden outdoor flight!

Video uploading soon.
http://www.vimeo.com/8807891

My build blog here.
https://www.rcgroups.com/forums/show...23&postcount=1

A total success, no damage sustained, not even a prop! This is attributed to the bumper, the foam landing gear and foam base. All this despite a windy day, leaves in the trees were swaying.
I had a lot of altitude excursions, suddenly up and down, due to the windy gusts and my inexperienced handling.

Thanks signguy and others for your help.
I experienced that near the end of a battery, before the Lipo alarm is even sounded, the tricopter motors are unstable and causes a twitching action.
This has nothing to do with gyro gain as it is stable throughout. This does not happen when the battery is fresh. I suspect the low voltage to the BEC causes the receiver, gyros, esc leads to be underpowered and glitchy.

1. Should I go with a separate battery for the BEC, maybe a 800 mah?
2. I can add a resistor to the lipo alarm to make it sound at a higher voltage by thinking it is at a lower voltage.
Jan 18, 2010, 10:23 AM
Hillary Lied, 4 Americans Died
Dave Barrow's Avatar
etman, congrats on the maiden. Those bumpers look great, I'll have to make a run to the toy store to get one.
Dave
Jan 18, 2010, 10:57 AM
Brushless
cdi3d's Avatar
Any one have an extra UBEC that they would part with? LHS is out and I need one for a new build - Thanks

Mike
Jan 18, 2010, 10:59 AM
Tri-Quad-Hexa-Octo-copters!!
Hi Sebastian,
Looks pretty stable for a very small sized tricopter compared to most other tricopter videos I believe you used the old Wolferl UAVP v3.15 tricopter firmware for the mini-tricopter setup in this video? https://www.rcgroups.com/forums/show...3#post11709393 I would like to suggest that you use Prof Greg's latest UAVX v1.891 firmware. You would have to upgrade your PIC to the 18F2620 to use the UAVX firmware. If you can't source and burn your own PIC, the 18F2620 plugin replaceable PIC processor is available preloaded with UAVX firmware at www.quadroufo.com for $15. The parameters have been rescaled and are somewhat different from the old Wolf UAVP firmware. Also for smaller quads and tricopters with less than 20cm motor to motor on axis spacing, the I2c ESC's, which the UAVP board can also use, might be more appropriate for even smoother flight. The standard ESC's such as Turnigy Plus, HCSuperSimple and Towerpros do fine with motor spacings greater than 20cm motor to motor on axis.
Cheers,
Jim
Quote:
Originally Posted by bas10an
UAVP micro tricopter, very unstable due to the small size, 15cm center to axle.
http://www.youtube.com/watch?v=kz1jel6ssDc

Sebastian.
Last edited by jesolins; Jan 18, 2010 at 11:19 AM.
Jan 18, 2010, 02:20 PM
Registered User
Talontsi96's Avatar
Yessss.....My parts from Hobby King arrived today...Yippee!!! Now I just gotta wait for the frame components from Jimto show up and we're off to the races......
Jan 18, 2010, 02:49 PM
Registered User
signguy's Avatar
Quote:
Originally Posted by Talontsi96
Yessss.....My parts from Hobby King arrived today...Yippee!!! Now I just gotta wait for the frame components from Jimto show up and we're off to the races......
I bet you could get a wooden or foam frame together before the other one arrives.
Jan 18, 2010, 02:52 PM
Registered User
rimshotcopter's Avatar
Quote:
Originally Posted by signguy
I bet you could get a wooden or foam frame together before the other one arrives.

Or even a Curtain Rod frame. LOL
Jan 18, 2010, 02:54 PM
Brushless
cdi3d's Avatar
I agree with Bob - So easy to swap out frames once you have all your harness's made - I am almost done with another one dedicated to 2 gyros and FMA copilot - Decided it will be a good one to work on my forward flight with - I bought some of those RCtimer motors and while they are lacking the same power that the DT750's have they are working ok - Again trying to go as light as possible - I have removed most of the bullet connectors in hopes of saving a little weight - -



Mike
Jan 18, 2010, 03:02 PM
Registered User
rimshotcopter's Avatar
Quote:
Originally Posted by cdi3d
I bought some of those RCtimer motors and while they are lacking the same power that the DT750's have they are working ok
Mike
Which RCtimer Motors do you have?
Jan 18, 2010, 03:14 PM
Brushless
cdi3d's Avatar
The 750kv's listed in the earlier post -

Mike


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Yet another tricopter build. !!Updated parts list!! SebastianJ Multirotor Drone Talk 2669 Dec 30, 2011 05:48 PM
Discussion What to do? Failed tricopter build! Razor_Racer Coaxial Helicopters 9 Mar 07, 2011 09:20 AM
Discussion Tricopter Build Razor_Racer Coaxial Helicopters 21 Feb 20, 2010 08:24 PM
Build Log Tricopter build SebastianJ VTOLs 1 Dec 22, 2008 04:34 PM
Discussion Trying to build a mechanically actuated tricopter, Help! stefalo Coaxial Helicopters 3 Jan 09, 2008 04:10 PM