Thread Tools
Old Oct 08, 2009, 03:25 PM
Hal_The_Hacker is offline
Find More Posts by Hal_The_Hacker
I Can Fly An FP Inverted!
Hal_The_Hacker's Avatar
Quote:
Originally Posted by ronaldf
My plastic version was ordered on Sep 25. I received notice that it shipped on Sep 26. No shipping info showed for about a week. It now states that it left Hong Kong on Oct 6. It sat in the Hong Kong mail facility for about 9 days. China holiday season????
yeah i recieved notice of it being shipped nine hours after i bought it, but it didnt get any tracking info for a further 6 days. i am pretty sure their postal service only collects once a week for non EMS orders
Sign up now
to remove ads between posts
Old Oct 08, 2009, 05:12 PM
distractor is offline
Find More Posts by distractor
Registered User
Quote:
Originally Posted by MakMov
That is probably from the control links on the slider rubbing on it from improper set up.
The tail was setup properly. I must not have spotted it when I looked over the tail.Remember, this had only had 4 minutes flight time.
Old Oct 08, 2009, 05:33 PM
Hal_The_Hacker is offline
Find More Posts by Hal_The_Hacker
I Can Fly An FP Inverted!
Hal_The_Hacker's Avatar
I have taken a load of pics of the GT and edited post #3 with these pics, here is a link:

https://www.rcgroups.com/forums/show...46&postcount=3


if anyone wants anymore pics, please dont hesitate to ask
Old Oct 08, 2009, 05:42 PM
tornadorc is offline
Find More Posts by tornadorc
Frequent Flyer
tornadorc's Avatar
Good job Hal, and nice pics, keep them comin.
Old Oct 08, 2009, 05:50 PM
tornadorc is offline
Find More Posts by tornadorc
Frequent Flyer
tornadorc's Avatar
Quote:
Originally Posted by lovespicyfood
On my HK450 build I replaced the HK feathering shaft and tail shaft with Align ones just to make sure...
Can someone please confirm this. If the Align T250 tail and Feathering shafts is compatible with the HK250.

thank you

Paul
Old Oct 08, 2009, 06:15 PM
MakMov is offline
Find More Posts by MakMov
Excellence is Expected
MakMov's Avatar
Quote:
Originally Posted by tornadorc
Can someone please confirm this. If the Align T250 tail and Feathering shafts is compatible with the HK250.

thank you

Paul

I can speak for the GT only.

Yes the Align feathering shaft will work.

The Align metal pully tail shaft did not fit, I had to replace the whole box.
Old Oct 08, 2009, 06:43 PM
mekaone is offline
Find More Posts by mekaone
Registered User
I have seen that the main drive gears and shaft were not compatible with the Trex 250. Does anyone know what the difference is? I am thinking that that should be something I would want to replace during the build. Does anyone know if there is anything else not compatible with the Trex 250 parts besides what I have seen somewhere else and the tail shaft block?
Old Oct 08, 2009, 06:52 PM
tornadorc is offline
Find More Posts by tornadorc
Frequent Flyer
tornadorc's Avatar
superkool, thanks Mak.

mekaone, I agree a list of compatibilty or interchangeable parts from the T250 to the HK250 would be good. or the other way around. which ever is easier.
Old Oct 08, 2009, 07:40 PM
GeneR is offline
Find More Posts by GeneR
Registered User
Well,
During the build of my plastic kit I tried the Align main shaft and it fit fine. The main gear as well was a direct fit.
Gene
Old Oct 08, 2009, 10:50 PM
mekaone is offline
Find More Posts by mekaone
Registered User
GeneR.
Thats very cool to know. I'v seen some where else that it was not compatible but you have first hand knowledge that that is not true. I guess I am looking at the aspect that I am not that good of a pilot and I know I am going to crash it a few times so it would be nice to be able to get parts at a local hobby shop rather than waiting a few weeks for parts from HobbyKing. I know a few weeks is not that bad but some times I just want to get back in to the air :-) Plus the more compatible it is, I think, would mean the better the longevity of this heli.
i can't wait till HAL_THE_HACKER and others have more to say about this cool little heli. Actually I can't wait till I get mine so I can start chatting about my views of the kit.
Old Oct 09, 2009, 03:17 AM
clicky is offline
Find More Posts by clicky
Registered User
@Hal_The_Hacker: Lucky you! I bet that mine is going to get stuck at depot at Heathrow during postal strike...

Quote:
Originally Posted by Hal_The_Hacker
I have taken a load of pics of the GT and edited post #3 with these pics, here is a link:

https://www.rcgroups.com/forums/show...46&postcount=3


if anyone wants anymore pics, please dont hesitate to ask
Great pics. At least I know what is coming my way! Please make some more when you put it together. Plus - maybe a video?
Old Oct 09, 2009, 07:39 AM
Evan D is offline
Find More Posts by Evan D
Registered User
Evan D's Avatar
None, not one of the clones is going to be 100% like the T250 (same goes for the 450 and 500 clones too). Bearings, tolerances, quality of materials will all be poorer. In many cases you'll have a few plastic parts instead of aluminium or a missing bearing. Over all if you want a straight up open the box, take out the instructions and build the helo get Align.

That said the clones are cheap, fun, and sometimes a challenge.

My 250Gt should be here today, then I get to figure out what I'll need to swap out too.
Old Oct 09, 2009, 08:54 AM
deanc338 is offline
Find More Posts by deanc338
Shut up and talk to me!!
My GT arrived yesterday and so far my parts audit seems complete and no missing what ever. I think....

The only thing I noticed is that there is a hole on the tail boom that is supposed to prevent the tail assembly from turning and there is nothing on the kit that will go there. I checked the Trex250 manual and it has a part that goes there that does that and the tail assembly looks different where it grips the boom. We'll check with HK support for answers, if none then a screw would be used.

Oh, the canopy is about 18grams, which I think is on the heavy side and the towerpro sg90 is a tight fit.

So far I'm happy, but wait until I dismantle the head to check deeper and put some thread lock.
Last edited by deanc338; Oct 09, 2009 at 09:08 AM.
Old Oct 09, 2009, 11:03 AM
Hal_The_Hacker is offline
Find More Posts by Hal_The_Hacker
I Can Fly An FP Inverted!
Hal_The_Hacker's Avatar
Quote:
Originally Posted by clicky
@Hal_The_Hacker: Lucky you! I bet that mine is going to get stuck at depot at Heathrow during postal strike...



Great pics. At least I know what is coming my way! Please make some more when you put it together. Plus - maybe a video?
no problem at all, i am waiting for my servos, which are coming with my hk250PL (my new name for the plastic version)
Old Oct 09, 2009, 11:04 AM
Hal_The_Hacker is offline
Find More Posts by Hal_The_Hacker
I Can Fly An FP Inverted!
Hal_The_Hacker's Avatar
Quote:
Originally Posted by Evan D
None, not one of the clones is going to be 100% like the T250 (same goes for the 450 and 500 clones too). Bearings, tolerances, quality of materials will all be poorer. In many cases you'll have a few plastic parts instead of aluminium or a missing bearing. Over all if you want a straight up open the box, take out the instructions and build the helo get Align.

That said the clones are cheap, fun, and sometimes a challenge.

My 250Gt should be here today, then I get to figure out what I'll need to swap out too.
actually, in this case you get aluminium parts instead of plastic, the bearing blocks and boom block are both plastic on the real thing, they are alu on this one.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Official HeliMax AXE CP Thread with pics post em here!!?.. darklyte24 Micro Helis 10606 Nov 19, 2015 02:32 PM
Build Log Nitroplanes Lander 70mm F9F Panther EDF Build Log and Review The Don Foamy EDFs 38 Jun 03, 2014 11:09 PM
GWS Spitfire Build thread (with glassing tutorial) David Winter GWS (Grand Wing Servo) 156 Sep 14, 2009 06:42 AM
Discussion Build log or review for BulleT? raycsr Electric Sailplanes 3 Jan 30, 2009 02:03 PM
looking for build thread with upclose photos HIGHFLYER99 Foamies (Kits) 13 May 21, 2005 09:54 PM