New Products Flash Sale
Thread Tools
Old Apr 20, 2003, 06:40 PM
soareyes is offline
Find More Posts by soareyes
Registered User

Source for Kontronik speed control in US or suggestion for replacement?

I seem to have fried my Kontronik Beat 50-8-30 speed control in my Logo 20 today. Where can I get a new one, or any suggestions for a replacement? My motor is a Kontronik Tango 45-08. These were both purchased used and I don't know where the original buyer purchased these.

I'm also unsure as to why the controller burned. The Logo is used but is new for me, and I had about 6 or 8 hovers over the last week with 24 cell packs. After each flight, I felt the speed control and motor, and they were always warm but never hot. About 4 minutes into my last hover, the motor shut off with no warning. Fortunately, I was only a few feet high so there was no damage. I felt the speed control and it was too hot to touch! Now it doesn't work.

Thanks for any advice!
Sign up now
to remove ads between posts
Old Apr 20, 2003, 09:40 PM
Bourbon is offline
Find More Posts by Bourbon
Registered User
Contact Fitz at, He has a controller listed for your motor, but it's not the same model you asked about. I'm sure he can help you out. The best time to contact or e-mail him is of an evening.

Good luck
Old Apr 20, 2003, 10:13 PM
amplifai is offline
Find More Posts by amplifai
Registered User
amplifai's Avatar
Contact Kontronik directly at the email address on their website. I f you send the controller back to them they will either repir it or sell you a new one at a discount. Mike looks after their customer service and is very helpful. My controller came back from Germany in less than a week.
Old Apr 21, 2003, 06:21 AM
RC Man is offline
Find More Posts by RC Man
A man with too many toys
Icare has good prices and fast service. Call or e-mail first to make sure it is in stock.
Old Apr 21, 2003, 07:31 PM
Steph280 is offline
Find More Posts by Steph280
1.21 Gigawatts!
Steph280's Avatar

Have you checked your motor to see if it still works? The older Tangos had problems with throwing magnets, which may fry the ESC when it happens. Check with motormike and he'll help you.

Old Apr 21, 2003, 09:19 PM
soareyes is offline
Find More Posts by soareyes
Registered User
Thanks guys for the replies. I'll contact Mike at Kontroniks and probably send the controller in for repair. Icare does have the same in stock if I decide to get a new controller (Fxaeromodels is out of stock). Icare also has Schultze controllers in stock, and a comparable one to the Beat is about $60 less. Any thoughts on using the Schultze with the Tango motor?

Also, how should I check my Tango to see if it did throw a magnet, as per Stephen's reply? It spins by hand with the same feel it did before, but should I take it apart to check? Thanks again!
Old Apr 22, 2003, 12:02 AM
Fred Bronk is offline
Find More Posts by Fred Bronk
Our Daddy and Heli Junkie
Fred Bronk's Avatar
The new Schulzes work fine with Tango motors.

I will add that Kontronik has great sevice too! My ungraded 45-6 came back in less than 2 weeks with all new parts, and the price was right!!

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Speed Control in SMD for Brushed Motor's Macdowell Electric Plane Talk 0 Jul 08, 2007 11:35 PM
Discussion Anyone know where to get a FIK-100 glider in the US, or a good setup for a FIK-60? Cheesehead Parkflyers 0 Sep 24, 2006 06:39 PM
For Sale/Speed Control Morris Boats (FS/W) 5 Jun 12, 2004 06:39 PM
im looking for a lrp speed control oznation Cars - Cars and Parts (FS/W) 0 Jan 06, 2004 08:15 PM
connectors for Shulze speed control whirlyspud Power Systems 20 Oct 15, 2002 09:36 AM