Shop our Airplanes Products Drone Products Sales
Thread Tools
Old Sep 08, 2012, 10:12 PM
edf_rookie is offline
Find More Posts by edf_rookie
Registered User
edf_rookie's Avatar
Sorry, another question. Where do you all get your standoffs from.

Just tried test mounting the motor and getting the placement for the cowl before I tightened it all down.

Appears I now need approx 10mm long standoffs with a 4mm inside diameter to get the proper spacing so the cowl fits in the corect place.

If nothing else, this plane is teaching me all the little extras I needed and hopefully where to get them from
Sign up now
to remove ads between posts
Old Sep 08, 2012, 10:18 PM
quadracer is offline
Find More Posts by quadracer
No, I won't ship it. Don't ask
quadracer's Avatar
Quote:
Originally Posted by edf_rookie View Post
Sorry, another question. Where do you all get your standoffs from.

Just tried test mounting the motor and getting the placement for the cowl before I tightened it all down.

Appears I now need approx 10mm long standoffs with a 4mm inside diameter to get the proper spacing so the cowl fits in the corect place.

If nothing else, this plane is teaching me all the little extras I needed and hopefully where to get them from
I've got a bunch of nylon/plastic standoffs from my 60" Extra that I have no use for. I think they are 4mm shaft size, and a couple different lengths. If you want them, PM me your address and I'll mail them to you.

EEK! Just noticed you're in Oz.... That might be more expensive to post than it would be worth..
Old Sep 08, 2012, 10:23 PM
edf_rookie is offline
Find More Posts by edf_rookie
Registered User
edf_rookie's Avatar
Quote:
Originally Posted by quadracer View Post
I've got a bunch of nylon/plastic standoffs from my 60" Extra that I have no use for. I think they are 4mm shaft size, and a couple different lengths. If you want them, PM me your address and I'll mail them to you.

EEK! Just noticed you're in Oz.... That might be more expensive to post than it would be worth..
Thanks for the offer but that's the problem being down here in Oz, it's virtually impossible to find standoffs and prop inserts down here. My building has come to standstill until I can source some.

That's why if I can find somewhere that sells them then I can order a large quantity of different sizes that I know I will need sometime in the future anyway.
Last edited by edf_rookie; Sep 08, 2012 at 10:29 PM.
Old Sep 08, 2012, 10:29 PM
quadracer is offline
Find More Posts by quadracer
No, I won't ship it. Don't ask
quadracer's Avatar
Yeah, you definitely want to buy in bulk down there. Have you tried a hardware store? Never know what you can find to "engineer" stuff together..
Old Sep 10, 2012, 08:57 AM
Wingin' Wayne is offline
Find More Posts by Wingin' Wayne
I like the violent stuff!
I agree with the hardware store. Suprising what you can find in the little slide out drawers. I too am a machinist, even a small shop in garage and I still check the hardware store first. I have been making things for the buds at the field for a while, popular item for the SC is way oversized aluminum washers for the SFG's. An 8x10 bushing may be a standard item in a big catalog like McMaster Carr. Bushings and standoffs should be easy to find. Good luck!
Old Sep 10, 2012, 09:15 AM
heritageflyer is offline
Find More Posts by heritageflyer
Time to Fly AJ's Best!
heritageflyer's Avatar
Anyone have any (Good) used CF LG for the 57 SC?

I caught a hole yesterday on a grass field and it twisted out my right leg at the pant. Split the layers.

PM if you do, I need it by this Friday, got another big Fly event in WV.

Otherwise I am ordering new LG today...
Old Sep 10, 2012, 03:38 PM
dentalpain is offline
Find More Posts by dentalpain
Registered User
dentalpain's Avatar
Here is some data for your consumption:
3DHS 57 Extra
Motrolfly 4315-714
Ice 100 Lite
Protek 15x7
Hitec HS225MG x4
Spektrum AR600
Gens Ace 4s4000 25C

Castlelink Settings:
Fixed End Points
Throttle Response: Medium (5)
Motor Start Power: Medium (59)
Motor Timing: Normal (5)
PWM Rate 12 Khz
Bec 6v
Logging Disabled.

Watts Up Power Readings: (End Points 73/74)
88 Amps
1370 Watts

Alt Settings
Throttle Respons: High (8)
Motor Start Power: Custom (75)
Motor Timing Low (0)
PWM Rate 8Khz

Watts Up Power Readings:
1240 Watts
82 Amps
Old Sep 10, 2012, 06:36 PM
bigroger is offline
Find More Posts by bigroger
Just flitting about!!
bigroger's Avatar
Quote:
Originally Posted by edf_rookie View Post
Thanks for the offer but that's the problem being down here in Oz, it's virtually impossible to find standoffs and prop inserts down here. My building has come to standstill until I can source some.

That's why if I can find somewhere that sells them then I can order a large quantity of different sizes that I know I will need sometime in the future anyway.
Mate,
I just used some 12mm square pine strip and cut some 15mm pieces. Drilled holes through them and mounted so the pre-machined 12mm thickness was on the mount side so as not to screw with the thrust angles etc.

Has worked really well, just don't over tighten onto the pine spacers or you will crush the pine standoffs.

Alternative is just to cut some 15mm dowl hardwood to size and drill through the centre. Problem with that is you need to pretty sure of the lengths or you alter the thrust angle.
Old Sep 10, 2012, 07:51 PM
DenverJayhawk is offline
Find More Posts by DenverJayhawk
Registered User
that is crazy. Those are exactly the same numbers I'm getting, static test. APC 15x10

Quote:
Originally Posted by dentalpain View Post
Here is some data for your consumption:
3DHS 57 Extra
Motrolfly 4315-714
Ice 100 Lite
Protek 15x7
Hitec HS225MG x4
Spektrum AR600
Gens Ace 4s4000 25C

Castlelink Settings:
Fixed End Points
Throttle Response: Medium (5)
Motor Start Power: Medium (59)
Motor Timing: Normal (5)
PWM Rate 12 Khz
Bec 6v
Logging Disabled.

Watts Up Power Readings: (End Points 73/74)
88 Amps
1370 Watts

Alt Settings
Throttle Respons: High (8)
Motor Start Power: Custom (75)
Motor Timing Low (0)
PWM Rate 8Khz

Watts Up Power Readings:
1240 Watts
82 Amps
Old Sep 10, 2012, 09:24 PM
FIXXIN2FLY is offline
Find More Posts by FIXXIN2FLY
FLY ANGRY
FIXXIN2FLY's Avatar
Quote:
Originally Posted by heritageflyer View Post
Anyone have any (Good) used CF LG for the 57 SC?

I caught a hole yesterday on a grass field and it twisted out my right leg at the pant. Split the layers.

PM if you do, I need it by this Friday, got another big Fly event in WV.

Otherwise I am ordering new LG today...
Hey Bro,
I landed mine hard the other day (frickin ccreations hard cut off in hover) and broke the bottom out of the plane but Im pretty sure the gear was intact. I understand the timelyness of the parts for shows and I have nothing going on for two weeks. If it would help I can send you mine to get you on the solid for the show. LMK
Old Sep 10, 2012, 09:29 PM
heritageflyer is offline
Find More Posts by heritageflyer
Time to Fly AJ's Best!
heritageflyer's Avatar
Quote:
Originally Posted by FIXXIN2FLY View Post
Hey Bro,
I landed mine hard the other day (frickin ccreations hard cut off in hover) and broke the bottom out of the plane but Im pretty sure the gear was intact. I understand the timelyness of the parts for shows and I have nothing going on for two weeks. If it would help I can send you mine to get you on the solid for the show. LMK
Thanks! But Aronph came through for me! He's almost local, so shipping out Gear tomorrow USPS Priority (1 day).
Old Sep 10, 2012, 09:33 PM
heritageflyer is offline
Find More Posts by heritageflyer
Time to Fly AJ's Best!
heritageflyer's Avatar

Doylestown Fall FunFly vid


Had a good day at D'Town yesterday. Shot vid of last flight of the 57.

Damaged that gear on the second landing, catching the right wheel and flipping over. Then on this one, tried to slow up and Harrier Plop so I would have short roll and not flip over again, but caught a little wind puff on the left side and more like Dropped it.

Other than that the flight was decent.

57 SC @ Doylestown Fall FunFly 2012 (4 min 29 sec)
Old Sep 10, 2012, 09:37 PM
FIXXIN2FLY is offline
Find More Posts by FIXXIN2FLY
FLY ANGRY
FIXXIN2FLY's Avatar
Quote:
Originally Posted by heritageflyer View Post
Thanks! But Aronph came through for me! He's almost local, so shipping out Gear tomorrow USPS Priority (1 day).
RIGHT ON BRO!!! GO GETTEM!!! Friends dont let friends fly broke
Old Sep 10, 2012, 10:55 PM
heritageflyer is offline
Find More Posts by heritageflyer
Time to Fly AJ's Best!
heritageflyer's Avatar
Quote:
Originally Posted by FIXXIN2FLY View Post
RIGHT ON BRO!!! GO GETTEM!!! Friends dont let friends fly broke
I still Feel Broke!
Old Sep 10, 2012, 11:07 PM
FIXXIN2FLY is offline
Find More Posts by FIXXIN2FLY
FLY ANGRY
FIXXIN2FLY's Avatar
Quote:
Originally Posted by heritageflyer View Post
I still Feel Broke!
LOL I was just saying that to a fellow addict at the field tonite. Even when shiz is going my way and taking things home in one piece, "I" still feel broke!!! >LOL< too funny


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product 3D Hobby Shop 47" Edge 540 #BUILD VIDEOS ADDED# ipsmotors 3D Flying 3960 Nov 23, 2013 08:39 PM
Video 3D Hobby Shop 57" Sukhoi sukhoi26mx Electric Plane Talk 7 Sep 17, 2008 09:33 AM
Sold NIB 3D Hobby Shop SHP Extra 300 *Blue* Version 2 thomer Aircraft - Electric - Airplanes (FS/W) 7 May 04, 2008 02:31 PM
Build Log 3D Hobby Shop 55" Katana LIVE Build Log Jeremy Sebens 3D Flying 54 Oct 12, 2007 04:39 PM