3D Hobby Shop 57" Extra 330 SC -Build Thread- - Page 543 - RC Groups
Thread Tools
Sep 27, 2011, 01:06 AM
I fly, therefore, I crash!!!
SteveT.'s Avatar
Quote:
Originally Posted by lammbn
Ok, quick question. Mounting my motor and the blind nuts will not seat fully due to the threaded portion bottoming out on my x-mount before the teeth are even 1/3 sunk into the firewall. Anybody have the same problem or a fix?
Yup..... Three suggestions, use bolts, nuts and washers instead of bolts and blind nuts, or put some plywood discs inside the firewall for the blind nuts to pull into. Or of course if you need spacers between the motor and the firewall to adjust for prop clearance then they can be on the front of the firewall.

SteveT
Latest blog entry: My hangar...
Sign up now
to remove ads between posts
Sep 27, 2011, 01:30 AM
iumop ap!sdn w,I
G.P.'s Avatar
When that happens I either drill the bottom of my standoffs bigger to go over the protruding blind nut, or I simply grind off the excess blind nut with my Dremel (after install) or bench grinder (before install).
Sep 27, 2011, 05:18 AM
Honeybadger don't care...
Luv3d's Avatar
Quote:
Originally Posted by SteveTtoooo
X9303 doesn't come with SD card, but JR does have software allowing you to store and modify your program on a computer. I have it, but it is buried right now, and I couldn't find it online, so a call to Horizon might be in order.

SteveT
Awesome info, SteveT, thanks! I'll look into it- it would be ideal to back up all these settings!
Sep 27, 2011, 10:12 AM
Hooked on 3DHS
lammbn's Avatar
Ok. Those were similar ideas that i had. Thanks for the insights!
Sep 27, 2011, 11:23 AM
Registered User
Alright, I'm super confused. I called aero-model/hacker. I was told the a40-12s is a FOUR cell motor and not to run 5 cell on it. They said the a40-14s is the 5 cell setup. This is confusing the heck out of me because ADC and 3dhs say the 12S is recommended for a 5s setup. I was also told I should run a 15x8 prop on a a40-12s. Confusion.
Sep 27, 2011, 11:43 AM
↓↘→ + (punch)
theKM's Avatar
Quote:
Originally Posted by chriscap
Alright, I'm super confused. I called aero-model/hacker. I was told the a40-12s is a FOUR cell motor and not to run 5 cell on it. They said the a40-14s is the 5 cell setup. This is confusing the heck out of me because ADC and 3dhs say the 12S is recommended for a 5s setup. I was also told I should run a 15x8 prop on a a40-12s. Confusion.
Hacker spec and advise their motors for people who want to stay at full throttle the whole flight... this isn't how we usually set up 3D planes however. We're usually after a higher peak performance, and only ever at full throttle for short periods of time. If you want to fly at full throttle all the time, the advice from Hacker isn't bad advice.

But as the numbers go up, the Kv of the motor goes down... the 10S is a faster motor per volt than the 12S and both faster than the 14S. For the higher thrust we generally seek for 3D, the 10S is our 4S recommendation, and the 12S for 5S.

...the 14S will work fine, it will want 5S, and a larger prop. Or stay on the same prop and you can also fly at full throttle for the whole flight
Sep 27, 2011, 11:47 AM
Registered User
That does make sense and somewhat echoes what they said. They were stressing full throttle performance.
Sep 27, 2011, 11:55 AM
Registered User
vienquach's Avatar
I'd prefer A40-12s on 5s, even with 15x8 prop.

Vien
Sep 27, 2011, 02:10 PM
Registered User
Quote:
Originally Posted by theKM
Hacker spec and advise their motors for people who want to stay at full throttle the whole flight... this isn't how we usually set up 3D planes however. We're usually after a higher peak performance, and only ever at full throttle for short periods of time. If you want to fly at full throttle all the time, the advice from Hacker isn't bad advice.

But as the numbers go up, the Kv of the motor goes down... the 10S is a faster motor per volt than the 12S and both faster than the 14S. For the higher thrust we generally seek for 3D, the 10S is our 4S recommendation, and the 12S for 5S.

...the 14S will work fine, it will want 5S, and a larger prop. Or stay on the same prop and you can also fly at full throttle for the whole flight
So what prop would you recommend for the 14s
Sep 27, 2011, 03:32 PM
I fly, therefore, I crash!!!
SteveT.'s Avatar
Quote:
Originally Posted by vienquach
I'd prefer A40-12s on 5s, even with 15x8 prop.

Vien
But then you always want Mo'powa!!! Personally, I think you should change your screen name to that.... :

SteveT
Latest blog entry: My hangar...
Sep 27, 2011, 04:13 PM
Registered User
Quote:
Originally Posted by vienquach
I'd prefer A40-12s on 5s, even with 15x8 prop.

Vien
Haha, I have to be one of the few running the A40-12s on 4S with a 15x6 prop! Not blistering by any means, but enough to get out of trouble and some damn nice flight times .
Sep 27, 2011, 04:16 PM
↓↘→ + (punch)
theKM's Avatar
Quote:
Originally Posted by chriscap
So what prop would you recommend for the 14s
I'd try out a 15x8 first to see how you like it... will be a good fall-back prop anyway. 16x8 is probably more likely closer to where you'll end up.
Sep 27, 2011, 04:30 PM
TEAM HILLBILLY
aronph's Avatar
Quote:
Originally Posted by kwiktsi
Haha, I have to be one of the few running the A40-12s on 4S with a 15x6 prop! Not blistering by any means, but enough to get out of trouble and some damn nice flight times .
and I thought I had the slowest setup....
Sep 27, 2011, 04:32 PM
Registered User
vienquach's Avatar
Quote:
Originally Posted by kwiktsi
Haha, I have to be one of the few running the A40-12s on 4S with a 15x6 prop! Not blistering by any means, but enough to get out of trouble and some damn nice flight times .
That's very little power.

Can you do rolling harrier with it ?

Vien
Sep 27, 2011, 04:38 PM
Registered User
vienquach's Avatar
Quote:
Originally Posted by SteveTtoooo
But then you always want Mo'powa!!! Personally, I think you should change your screen name to that.... :

SteveT
More power is nice, but I prefer it to be light also.

Sometimes, too much power is a bit twitchy to handle.

Vien


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product 3D Hobby Shop 47" Edge 540 #BUILD VIDEOS ADDED# ipsmotors 3D Flying 3966 Sep 14, 2017 03:08 PM
Video 3D Hobby Shop 57" Sukhoi sukhoi26mx Electric Plane Talk 7 Sep 17, 2008 09:33 AM
Sold NIB 3D Hobby Shop SHP Extra 300 *Blue* Version 2 thomer Aircraft - Electric - Airplanes (FS/W) 7 May 04, 2008 02:31 PM
Build Log 3D Hobby Shop 55" Katana LIVE Build Log Jeremy Sebens 3D Flying 54 Oct 12, 2007 04:39 PM