Thread Tools
Old Sep 11, 2009, 08:59 PM
BoneDoc is offline
Find More Posts by BoneDoc
Team 3DHS
BoneDoc's Avatar
Yep, clear packing tape is what I'd use.
Sign up now
to remove ads between posts
Old Sep 11, 2009, 09:07 PM
Manta1 is offline
Find More Posts by Manta1
OOPS
Manta1's Avatar
ive never put that piece on my planes anyhow
Old Sep 11, 2009, 09:07 PM
brucewsb is offline
Find More Posts by brucewsb
Registered User
brucewsb's Avatar
So after looking at the cowling, I'm thinking about building some mounting hardware to clamp the cowl to the firewall instead of using screws from the outside. Looks doable if I just reinforce the wooden edge. Might be tricky access but I'll see if some creative spark happens.

Anybody else planning something like that? Just seems too nice looking to blemish with screws.
Old Sep 11, 2009, 09:12 PM
refugeefromcalif is offline
Find More Posts by refugeefromcalif
May the Farce be with you...
refugeefromcalif's Avatar
Quote:
Originally Posted by Manta1
ive never put that piece on my planes anyhow
I don't either.
I also don't use wheel pants because of the places I fly at.
I like, Full access to the gear bolts for an easy replacement.

George
Old Sep 11, 2009, 09:12 PM
M Carr is offline
Find More Posts by M Carr
Registered User
M Carr's Avatar
Woooooo Hoooooo, almost finished with mine...

All I have left to do is Install receiver, hook up servos, setup radio and check CG. I could actually fly it tomarrow but it will probably be Sunday as originally planned.

So far I'm at 7lbs 8ozs minus receiver and main battery. not too bad for a 70" airframe.
Old Sep 11, 2009, 09:15 PM
Manta1 is offline
Find More Posts by Manta1
OOPS
Manta1's Avatar
i will put the wheel pants on this one.i put them on my vyper and so far so good,but it lands easy as a sig kadet senior so ive always landed it on the mat.as far as the 70 goes..i imagine it will run on the grass a bit
Old Sep 11, 2009, 10:19 PM
rthorne is offline
Find More Posts by rthorne
Quit Chucking My Wood
rthorne's Avatar
Quote:
Originally Posted by M Carr
Woooooo Hoooooo, almost finished with mine...

All I have left to do is Install receiver, hook up servos, setup radio and check CG. I could actually fly it tomarrow but it will probably be Sunday as originally planned.

So far I'm at 7lbs 8ozs minus receiver and main battery. not too bad for a 70" airframe.
Good job Mick.

Rich
Old Sep 11, 2009, 11:59 PM
G.P. is online now
Find More Posts by G.P.
iumop ap!sdn w,I
G.P.'s Avatar
Soory, wrong thread!
Old Sep 12, 2009, 12:08 AM
chimchim is offline
Find More Posts by chimchim
Registered User
Is it built yet Manta?
Old Sep 12, 2009, 12:11 AM
Manta1 is offline
Find More Posts by Manta1
OOPS
Manta1's Avatar
Quote:
Originally Posted by chimchim
Is it built yet Manta?
its in the airplane shop at my buds house.(local flying field) i havent even gon and got it yet.needed to rest this evening.if i had went and gotton it id still be working on it.lol ive held this couch down and blown my nose all evening lol..sorry
Old Sep 12, 2009, 05:54 AM
jadamian75 is offline
Find More Posts by jadamian75
Registered User
jadamian75's Avatar
Up to build video 4. Its looking good. Today I may go out and get bigger wheels. Maybe kavans. I'd like to keep them lite/durable and need something I can find within a 1/2 hour drive. The bigger wheels are because the back of the wheel pant are almost touching the ground. I already drilled the 2 wood screws per wheel pant so I think the easiest way to get the wheel pants higher is larger wheels. There is plenty of room inside the wheel pants to go bigger.

Joe
Old Sep 12, 2009, 08:46 AM
callen is offline
Find More Posts by callen
WAR EAGLE
callen's Avatar
Quote:
Originally Posted by Daloaf
I usually remove the monocote, sand down the edges so it sits flush and then CA the covering back down on the sides. I use some clear packing tape to tape the block into place. That way if I break the gear, I can easily remove the block to get to the gear bolts.

Matt
This is the way to go. Cause you know sooner or later that carbon gear is going to crack.
Old Sep 12, 2009, 08:48 AM
callen is offline
Find More Posts by callen
WAR EAGLE
callen's Avatar
Quote:
Originally Posted by brucewsb
So after looking at the cowling, I'm thinking about building some mounting hardware to clamp the cowl to the firewall instead of using screws from the outside. Looks doable if I just reinforce the wooden edge. Might be tricky access but I'll see if some creative spark happens.

Anybody else planning something like that? Just seems too nice looking to blemish with screws.
I'm surprised it wasn't designed that way since it fits flush. I've been also toying with your same idea. Its the bottom that will be the hard part.
Old Sep 12, 2009, 10:30 AM
Tipover is offline
Find More Posts by Tipover
Registered User
I would think Velcro would be a good way to hold the landing gear filler bock in place. Of course the filler block would need to be designed to accommodate the thickness of the Velcro.

Kevin
Old Sep 12, 2009, 10:32 AM
Manta1 is offline
Find More Posts by Manta1
OOPS
Manta1's Avatar
just counter since some of those strong earth magnets and stick it to it


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Poll 3D hobby shop 51" slick or 55" SHP? appleflyer 3D Flying 24 Mar 24, 2009 07:29 PM
Video 3D Hobby Shop's AJ Slick Clark Warfel Electric Plane Talk 3 May 08, 2008 08:31 AM