3D Hobby Shop 71" AJ Slick - Build & Fly thread - Page 1699 - RC Groups
Thread Tools
Oct 09, 2012, 01:07 PM
Registered User
robj's Avatar
Quote:
Originally Posted by going4speed
yea stock seems REALLY low right now and only back in stock in 2013
Did you make it to Austin? Trying to PM ya but I don't see it on your page.

Rob
Sign up now
to remove ads between posts
Oct 09, 2012, 01:29 PM
TEAM HILLBILLY
Eagle34's Avatar
Quote:
Originally Posted by going4speed
I still consider the 71" yours.

The above was in relation to my 40" edge.
Cool. Wasn't sure. Didn't want you to think I backed out on you or anything.
Last edited by Eagle34; Oct 09, 2012 at 01:35 PM.
Oct 09, 2012, 02:02 PM
3DHS 'native'
going4speed's Avatar
Yea I was there Thursday, Friday and Saturday. Did not make it to the meet and greet on Saturday.

Quote:
Originally Posted by robj
Did you make it to Austin? Trying to PM ya but I don't see it on your page.

Rob
Oct 09, 2012, 04:14 PM
Registered User
SnowDog1974's Avatar
Quote:
Originally Posted by Eagle34
Not exactly sure but it seemed that the electric 71's were out of stock for almost a year. They had the gas ones, but they just got the electrics back in and now the gassers are out. You will want to contact ADC Hobbystore anyway as they are the worldwide distributors for 3DHS, Rob maight actually have one in stock, never know.
That's why I bought a red 71" Gas Slick earlier this year, even though I knew I wouldn't be able to afford all the internals until this fall...now I'm looking at a really fun winter building project and a really great start to spring flying! The gas 71" Slicks were out of stock for almost six months IIRC, so I bought one as soon as they came back in stock (earlier this summer).
Oct 09, 2012, 04:48 PM
3DHS 'native'
going4speed's Avatar
yea I need to get a back up for christmas if they come back in stock
Oct 09, 2012, 07:00 PM
Santi
DaaBears's Avatar
Flew the absolute piss out of my newly inherited slick! Wow, just wow! I already loved my 51, but the 70" just blew my mind! Already can't wait for an 89"... I truly understand the slickness sickness!
Oct 09, 2012, 07:53 PM
Registered User

Canopy latch


Does anyone have issues with the canopy latch pin being too short?

I'm finishing the Slick and discovered my canopy latch pin does not go all the way through the canopy plywood doubler when the canopy is fitted and latched. When fully extended it only goes through about half way in the canopy frame: It latches only onto the balsa part of the canopy bulkhead instead of all the way through the plywood doubler. All my other Slick latch all the way through.

It looks like the latch is glued in the right place and length of the pin is correct, any longer it would scrape when fitting the canopy. Maybe the canopy is a bit distorted so the fit is not perfect. The magnets are holding it very tight and the pin latches, but just not fully.

Am I going to have problems with the canopy blowing off?
Last edited by Huang; Oct 09, 2012 at 08:41 PM. Reason: Spelling
Oct 09, 2012, 07:57 PM
3DHS 'native'
going4speed's Avatar
Use the side bolts and you should be fine.
Oct 09, 2012, 08:03 PM
Registered User
M Carr's Avatar
I'm betting all you need to do is file the hole in the plywood former down just a little to the same level of the balsa... Had to do it to one of mine, Just be sure not to file more than needed so it still latches the canopy down tight.
Oct 09, 2012, 08:12 PM
No, I won't ship it. Don't ask
quadracer's Avatar
My canopy just required a slight wiggle, then the pin would pop all the way through.
Oct 09, 2012, 08:21 PM
The Twisted Elf
lugnutz's Avatar
i had to enlarge the hole on all 3 of my planes ,2- 71"slicks and 72" extra
Oct 09, 2012, 08:48 PM
Registered User
A bit hard to explain this, it's not the latch is being restricted. The latch pin is already fully extended, but still does not go all the way through the ply doubler. It only has enough reach to go through the canopy balsa bulkhead.

It could be my canopy is slightly warped, or the canopy back plate is glued slightly inner to where it should be. It's just 1-2mm off but the latch can't hook onto the ply doubler when fully extended. Does it need to hook onto the ply doubler?

I'd rather not have to use the thumb screws if possible. Hard to disconnect the battery quickly in case anything happens.
Oct 09, 2012, 09:04 PM
I fly, therefore, I crash!!!
SteveT.'s Avatar
Quote:
Originally Posted by UCDme3D
Flew the absolute piss out of my newly inherited slick! Wow, just wow! I already loved my 51, but the 70" just blew my mind! Already can't wait for an 89"... I truly understand the slickness sickness!
They do fly great don't they!!!!

SteveT
Latest blog entry: My hangar...
Oct 09, 2012, 09:06 PM
I fly, therefore, I crash!!!
SteveT.'s Avatar
Quote:
Originally Posted by Huang
Does anyone have issues with the canopy latch pin being too short?

I'm finishing the Slick and discovered my canopy latch pin does not go all the way through the canopy plywood doubler when the canopy is fitted and latched. When fully extended it only goes through about half way in the canopy frame: It latches only onto the balsa part of the canopy bulkhead instead of all the way through the plywood doubler. All my other Slick latch all the way through.

It looks like the latch is glued in the right place and length of the pin is correct, any longer it would scrape when fitting the canopy. Maybe the canopy is a bit distorted so the fit is not perfect. The magnets are holding it very tight and the pin latches, but just not fully.

Am I going to have problems with the canopy blowing off?
Mine did less than 90 seconds into the maiden flight....use the screws!!

SteveT
Latest blog entry: My hangar...
Oct 09, 2012, 09:17 PM
Registered User
dentalpain's Avatar
Maybe a washer glued to the back of the hole on the canopy would help


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Poll 3D hobby shop 51" slick or 55" SHP? appleflyer 3D Flying 24 Mar 24, 2009 07:29 PM
Video 3D Hobby Shop's AJ Slick Clark Warfel Electric Plane Talk 3 May 08, 2008 08:31 AM