Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Jul 14, 2011, 11:59 PM
Sukhoikid is offline
Find More Posts by Sukhoikid
Team Futaba / Team RMRC
Sukhoikid's Avatar
Check out my hacker motor today and two magnets were sliding out. Popped open the motor and fixed it and seems to be working fine now. Put the apc prop on there and everything is running much cooler now.
Sign up now
to remove ads between posts
Old Jul 15, 2011, 07:07 AM
cayars is offline
Find More Posts by cayars
Registered User
cayars's Avatar
Quote:
Originally Posted by Choppedlow View Post
Amazing the difference an inch makes (that's what she said!)
Has she been testing different sizes?
Old Jul 15, 2011, 11:12 AM
nsg is offline
nsg
Find More Posts by nsg
nsg
Registered User
I'm about to start working on my 71. Since the manual is a bit obsolete - any differences in build/assembly process compared to 68 Velox and 65 Vyper?
Old Jul 15, 2011, 01:09 PM
robj is offline
Find More Posts by robj
Registered User
robj's Avatar
Quote:
Originally Posted by nsg View Post
I'm about to start working on my 71. Since the manual is a bit obsolete - any differences in build/assembly process compared to 68 Velox and 65 Vyper?
IMO, you build one you can build them all. Only doublecheck part is the elevator halves and how they go.

The 70 manual is probably close enough.
Old Jul 15, 2011, 01:10 PM
Manta1 is offline
Find More Posts by Manta1
OOPS
Manta1's Avatar
Quote:
Originally Posted by nsg View Post
I'm about to start working on my 71. Since the manual is a bit obsolete - any differences in build/assembly process compared to 68 Velox and 65 Vyper?
not really,if you have built a velox then you already got the skillz bro.
You can go by the 70 slick manual too and be hunky dory
Old Jul 15, 2011, 01:14 PM
robj is offline
Find More Posts by robj
Registered User
robj's Avatar
Quote:
Originally Posted by 94'325is View Post
It's not that I don't like it, I'm just pushing it a little too much and before I do any permanent damage to it I'd rather replace it. When I was on the 18x8 I was at 1950 Watts which was no problem for the motor but it's getting hot here so I threw a 19x8 on it because the hot air was killing my pullout out of hover. I flew it a few times w/ the 19x8 at 2200ish Watts and the motor came down warmer than I wanted. I do like Scorpions though, this is my 4th one and I've never had issues with them. It's also a lot lighter than most motors it's size.
I've got 2 and like them so far. The vyper was running hot, not much cooling, I added a duct in the cowl and it runs a lot cooler now. Did the same for the 70 but never really had much heat problem. After 6 minutes, could hold my hand on it as long as i wanted.

It's about 3oz lighter than other motors to. But I'm going with a hacker a50 14L for the new Edge.
Old Jul 15, 2011, 01:17 PM
nsg is offline
nsg
Find More Posts by nsg
nsg
Registered User
Thanks, guys. Will be building it next week, most likely.. depending how much s..tuff I get at work.
Old Jul 15, 2011, 05:52 PM
CreepEdge is offline
Find More Posts by CreepEdge
You Won't Know till You Try
Quote:
Originally Posted by losifanatic View Post
My brother Nick just built his new 71 slick and maidened it today. Congrats Nick. Wish I
could have been there to see it
Thanks It all went well .However the wind was blowing it's arse off. But I wanted to fly it so I managed
Old Jul 15, 2011, 05:55 PM
Safety Hawk is offline
Find More Posts by Safety Hawk
Here We Go!
Safety Hawk's Avatar
Congrats Nick. Yeah......been blowing here too! But at least it's not hot.
Old Jul 15, 2011, 05:58 PM
CreepEdge is offline
Find More Posts by CreepEdge
You Won't Know till You Try
here is the Video of the Maiden Flight
Maiden flight 71" slick (3 min 35 sec)
Old Jul 15, 2011, 06:02 PM
Safety Hawk is offline
Find More Posts by Safety Hawk
Here We Go!
Safety Hawk's Avatar
Gotta love the 5mph upwind passes and the 90mph downwind passes.
Old Jul 15, 2011, 09:47 PM
CreepEdge is offline
Find More Posts by CreepEdge
You Won't Know till You Try
Quote:
Originally Posted by Safety Hawk View Post
Gotta love the 5mph upwind passes and the 90mph downwind passes.
I plan on getting some better video this weekend. then I'll have non wind assisted fly bys
Old Jul 15, 2011, 09:50 PM
losifanatic is offline
Find More Posts by losifanatic
Sippin the Koolaid!
losifanatic's Avatar
I am flying mine tomorrow morning
Old Jul 15, 2011, 09:52 PM
Ohio AV8TOR is online now
Find More Posts by Ohio AV8TOR
On loan to Texas
Ohio AV8TOR's Avatar
Quote:
Originally Posted by losifanatic View Post
I am flying mine tomorrow morning
Going for my maiden tomorrow morning. Has to be morning because it has been 104 for some time. I will be out at 6.
Old Jul 15, 2011, 09:56 PM
losifanatic is offline
Find More Posts by losifanatic
Sippin the Koolaid!
losifanatic's Avatar
Let me know how it goes!!! Good luck!


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Poll 3D hobby shop 51" slick or 55" SHP? appleflyer 3D Flying 24 Mar 24, 2009 07:29 PM
Video 3D Hobby Shop's AJ Slick Clark Warfel Electric Plane Talk 3 May 08, 2008 08:31 AM