Shop our Airplanes Products Drone Products Sales
Thread Tools
Old Aug 12, 2009, 12:37 AM
giddyuperic is offline
Find More Posts by giddyuperic
Registered User
giddyuperic's Avatar
I use Hitec 82 MG if you can't get them. Parkzone servo for the rudder and streering in a metal geared servo and works great. The hitec in 21 bucks and the parkzone is about 12 dollars. Make sure it is the one for the rudder/streering.
Sign up now
to remove ads between posts
Old Aug 12, 2009, 01:58 AM
Prof100 is offline
Find More Posts by Prof100
Registered User
Prof100's Avatar
Quote:
Originally Posted by skyline_g35
Did you guys take a look at my vid?

Tell me what you think of the landing...
Great maiden video. Landing was very smooooooth.
Old Aug 12, 2009, 10:55 AM
X30PILOT is offline
Find More Posts by X30PILOT
Registered User
X30PILOT's Avatar
Just some quick observations before I start building this thing. The kit looks great, and that CNC metal fan is very impressive.
I purchased my kit from Max at http://parkrcmodels.com . Considering the current issues with some of the online venders, I have to say that dealing with Max was an extremely positive experience!
The main gear retracts in the wing work nice and smooth, however the nose gear retract is binding. If I cannot resolve the binding issue I am concerned that a stalled servo could brown out my AR 7000. I fly mostly off of grass fields so forgoing the gear altogether would skip 4 servos. This would not only reduce weight, but the amp draw of those servos on the bec. The video that Extreme RC posted flying off of the grass was very impressive.

Any thoughts?

Thanks

X-30
Old Aug 12, 2009, 12:20 PM
crxmanpat is offline
Find More Posts by crxmanpat
Foam abuser!
crxmanpat's Avatar
If you are going full house on this plane (8+ servos), I HIGHLY recommend using a separate NiMH or A123 pack for the RX power. I don't trust an internal BEC with any more than 3 servos, or an external BEC at all (I've had CC BECs melt on me).

If you want to keep the LG in, then work with the nose gear until you resolve the binding issue. BTW, what part of it is binding? I've had to rework the pre-bent wires some on my Panther and F-16 to get things to work just right.

Pat
Old Aug 12, 2009, 01:11 PM
X30PILOT is offline
Find More Posts by X30PILOT
Registered User
X30PILOT's Avatar
Pat,

Thatís probably some good advice on the BEC, although I am running my Trex 500 with 4 medium sized digital servos and a gyro on the Align 60 amp ESC with a built in BEC.
If I go the full house route Iíll be running 10 servos. 3 retract 1 nose wheel steering
2 aileron, 2 flap 1 elevator and 1 rudder. The linkage on the nose wheel looks fine but I may have to disassemble the unit and lube the moving parts.

Thanks

Dave
Old Aug 12, 2009, 02:16 PM
Jimmy_H is offline
Find More Posts by Jimmy_H
Jimbo and the Jet Set
Jimmy_H's Avatar
I replaced the bent wire with straight, used a 12g mg 2kg towerpro servo and added a balsa block to stop the stall when the two forces meet.

the attached should help
Old Aug 12, 2009, 11:46 PM
X30PILOT is offline
Find More Posts by X30PILOT
Registered User
X30PILOT's Avatar
Jimmy_H

Thank you for posting that picture of your nose wheel installation.
Have you test flown your Hunter?

Thanks

Dave
Old Aug 13, 2009, 01:34 AM
Patrik J is offline
Find More Posts by Patrik J
Registered User
Is it possible to fit air retracts on this bird?
Considering a mini metal air set and get rid of a couple of servos.

I have not yet received my Hawk, so I don't know if there's any space to put the air tank.

//
Patrik
Old Aug 13, 2009, 02:29 AM
Parkflying is offline
Find More Posts by Parkflying
Quote:
Originally Posted by X30PILOT
Just some quick observations before I start building this thing. The kit looks great, and that CNC metal fan is very impressive.
I purchased my kit from Max at http://parkrcmodels.com . Considering the current issues with some of the online venders, I have to say that dealing with Max was an extremely positive experience!
The main gear retracts in the wing work nice and smooth, however the nose gear retract is binding. If I cannot resolve the binding issue I am concerned that a stalled servo could brown out my AR 7000. I fly mostly off of grass fields so forgoing the gear altogether would skip 4 servos. This would not only reduce weight, but the amp draw of those servos on the bec. The video that Extreme RC posted flying off of the grass was very impressive.

Any thoughts?

Thanks

X-30
Thanks for the kind words.
Is the servo over throwing or is the mechanism just rough and not working smooth? If it is a bad mechanism, get to me in email and we will work on a replacement for you. Also have you looked at the Suspension Struts for the Hunter? Really sweet!
Also I use these Du-Bro servo savers for situations like this where the servo might over throw or on the steering servo.
Take a look here: Du-Bro Servo Saver

Hope that helps

Max
Site Sponsor
Old Aug 13, 2009, 09:20 PM
muckie is offline
Find More Posts by muckie
Situationally Unaware
muckie's Avatar
This mat be one of the dumbest questions ever asked but:

How is easy is it for everyone to release the cockpit/battery hatch?

I haven't assembled the fuse yet but at the moment the only way I can get the hatch off is to push it from below. I can't see how I'll get it off when the lower front fuse is attached. Maybe I should swap the plastic latches for a couple of magnets...

Cheers!
Old Aug 13, 2009, 09:23 PM
Extreme_RC is offline
Find More Posts by Extreme_RC
Extreme CNC Alloy EDF
Extreme_RC's Avatar
The catch is good, once you have stuck the canopy down with decent quality double sided tape you will be able to pull the hatch up at the front edge by holding the canopy, same for all the Lander models. I have not had an issue yet with any of mine, broke the Panther one eventually but the canopy had been removed MANY times
Old Aug 13, 2009, 09:29 PM
muckie is offline
Find More Posts by muckie
Situationally Unaware
muckie's Avatar
Thanks, Extreme.
That's good to know.
Nice video earlier!

Cheers
Old Aug 14, 2009, 03:09 AM
giddyuperic is offline
Find More Posts by giddyuperic
Registered User
giddyuperic's Avatar
What I did was took two pieces of plastic you know like something would come in from the store like a servo package and cut a L shape out of it and glued it to the front of the hatch to make a handle to pull up on the hatch. They work so good I have them on all of my RC Lander air planes and the clear plastic you can not see so it works great. If you need photos just ask. Okay Eric
Old Aug 14, 2009, 08:19 AM
muckie is offline
Find More Posts by muckie
Situationally Unaware
muckie's Avatar
Quote:
Originally Posted by giddyuperic
What I did was took two pieces of plastic you know like something would come in from the store like a servo package and cut a L shape out of it and glued it to the front of the hatch to make a handle to pull up on the hatch. They work so good I have them on all of my RC Lander air planes and the clear plastic you can not see so it works great. If you need photos just ask. Okay Eric
Eric - that's a great idea - thanks!
Old Aug 14, 2009, 10:14 AM
X30PILOT is offline
Find More Posts by X30PILOT
Registered User
X30PILOT's Avatar
Extreme_RC


How is your Hunter holding up after repeated belly landings on the grass?
Did you put anything on the bottom to protect it?

Thanks

Dave


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Cool New Mini FuntanaX from e-flite (official build thread/ flying thread!!) p51flyer 3D Flying 1741 Oct 30, 2016 04:41 PM
Yippee! RWDRC Hawker Sea Fury Build Thread iflyprops Scale Kit/Scratch Built 414 Sep 09, 2008 12:09 PM
DC-9 Airliner for EDF-50BH - Official Build Thread Hawker Electric Ducted Fan Jet Talk 77 May 29, 2007 10:54 PM
Aerodrome RC Fokker D.VII - Pictorial build thread Admiral Piett14 Scale Kit/Scratch Built 11 Oct 17, 2005 01:59 PM
Hawker Hunter official list starting U812 Electric Ducted Fan Jet Talk 47 Aug 01, 2003 08:07 PM