Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Jun 18, 2009, 10:25 AM
mmormota is online now
Find More Posts by mmormota
Registered User
mmormota's Avatar
Video

REmzibi OSD current sensor test


This is a test video of the diy current sensor for the Remzibi OSD.

The battery voltage, the current and the mAh is measured same time by the diy sensor and the Emeter.
Check the voltage, current and mAh (marked with just m as no mAh character in the table) in the bottom left of the screen and the corresponding values on the Emeter's screen.
(the gps is not locked, so no bother with any other data but these three in bottom left)

Remzibi: there is a possible firmware bug, did you observed the unknown unintended "9m" displayed for a few seconds above the voltage value?
Sign up now
to remove ads between posts
Old Jun 18, 2009, 11:47 AM
HappyKillmore is offline
Find More Posts by HappyKillmore
Suspended Account
That 9m is the wrap around text from one line up on the far right. You must be careful with the objects you put on the right border. If they get too big, they wrap around to the next line down on the left.
Old Jun 18, 2009, 02:11 PM
remzibi is offline
Find More Posts by remzibi
Registered User
remzibi's Avatar
As HappyKillmore wrote - it is information from line above - was too long to feet in line so gone on next one .
Old Jun 18, 2009, 03:54 PM
mmormota is online now
Find More Posts by mmormota
Registered User
mmormota's Avatar
Thank you.
I move it two steps left. Then in normal flight session - if the plane doesn't fly above the atmosphere - it would not happen...
Old Jul 23, 2009, 07:24 PM
FPVExtremer is offline
Find More Posts by FPVExtremer
Putting FPV to Business
FPVExtremer's Avatar
That's great, it seems that I am going to order one for me...let's wait for the PM response from Remzibi.

Thanks mmormota for your attention.

Cheers,

Ernani
Old Oct 02, 2009, 06:28 AM
Tuven is offline
Find More Posts by Tuven
Alexander/Sweden
Tuven's Avatar
Hi

Could you digg up some more info about the current sensor you have made?
Old Oct 02, 2009, 11:04 AM
badpilotto is offline
Find More Posts by badpilotto
BadPilot
badpilotto's Avatar
HappyKillmore,

That is awesome a premade diy current sensor for the Remzibi OSD. I thought when I started to FPV I would have to build my own equipment. I checked out the web-site and that is very good price.

Thanks to mmormota for posting the vid or I would never have found this.

John
Old Oct 10, 2009, 11:13 AM
HappyKillmore is offline
Find More Posts by HappyKillmore
Suspended Account
FYI, the newer updates to the config software have some basic checks for objects overwriting one another. Please download the latest and look for the objects that turn red. They have a strong possibility to overwrite another object.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Help! dragon osd current sensor problem Don Moretti FPV Talk 2 May 23, 2009 03:53 AM
Discussion BlackStork OSD - Current sensor pinout jacky65 FPV Talk 0 Jan 06, 2009 05:06 AM
Sold Vizion OSD with current sensor ($50 shipped) + video switch VasMan Aircraft - General - Miscellaneous (FS/W) 1 Dec 21, 2008 05:21 PM
Discussion Black Stork OSD Current Sensor Calibration Question:) danje FPV Talk 6 Oct 31, 2008 01:25 PM
Sold Vizion OSD (V3) with Current Sensor - $80.00 SHIPPED VasMan Aircraft - General - Miscellaneous (FS/W) 1 Jun 13, 2008 02:39 AM