New Products Flash Sale
Thread Tools
Old Jan 10, 2011, 09:54 AM
Thermalin is offline
Find More Posts by Thermalin
I'm a pilot, 100 yrs too late
Thermalin's Avatar
I'm going to be using solartex also but the pre-painted variety as the base covering . Does anyone know how the lusterkote type paints would hold up on solartex. I was hoping to use these for the design rather than a second layer of covering?
Mike
Sign up now
to remove ads between posts
Old Jan 10, 2011, 09:57 AM
TomCrump is offline
Find More Posts by TomCrump
ARFs Are Me
TomCrump's Avatar
Haven't tried it, but I think Lustrekote will work well for you.
Old Jan 10, 2011, 11:20 AM
EJWash1 is offline
Find More Posts by EJWash1
AMA 910957
EJWash1's Avatar
Cloverdale,

Thanks. I've been a woodworker for thirty-some years, and trust me, having the right tools make you look good!

Quote:
Originally Posted by Cloverdale View Post
I am interested in how Solartex compares to film for ease of use?
I haven't covered a model with film since the early '80s, and that was using Monokote and Coverite and just using one covering iron and a heat gun. You set the iron by trial and error and hoped for the best. Seems a lot of guys like Ultra Cote, but I haven't heard anyone compare it to Solartex.

EJWash
Old Jan 10, 2011, 11:25 AM
EJWash1 is offline
Find More Posts by EJWash1
AMA 910957
EJWash1's Avatar
Thermalin,

I'm betting that Tom is right.

Right on the can, it reads that LustreKote can be used over MonoKote, so it must have the adhesion and elasticity to hold.

EJWash
Old Jan 10, 2011, 11:28 AM
Thermalin is offline
Find More Posts by Thermalin
I'm a pilot, 100 yrs too late
Thermalin's Avatar
ahh.. ok... i thought i read online it was more hard materials like balsa, fiberglass.. plastics, etc.. that's good then, I must have had a senior moment. I' little leary of picking up some the LHS as I don't think the inv for that turns over very much.
Mike
Old Jan 10, 2011, 11:33 AM
EJWash1 is offline
Find More Posts by EJWash1
AMA 910957
EJWash1's Avatar
Just to make sure we're talking about the same stuff:

http://www.monokote.com/lustrekote/lustrekote.html

EJWash
Old Jan 10, 2011, 11:56 AM
mike2663 is offline
Find More Posts by mike2663
Hey Guys, Watch This.......
mike2663's Avatar
I've used lustrekote it over monokote but scuffed the covering with 00 steel wool to give the paint something to adhere too. Worked very well.
Mike
Old Jan 10, 2011, 02:45 PM
TomCrump is offline
Find More Posts by TomCrump
ARFs Are Me
TomCrump's Avatar
If you buy Lustrekote, buy it from Tower. They have a larger turnover than the LHS. Your paint will be more fresh.

Steal wool is not suggested for Solartex. The steal dust can be trapped in the "tex", with the possibilty of rust, later on. It's fine, as Mike suggests, on Monokote.
Old Jan 10, 2011, 04:30 PM
panzercreation is offline
Find More Posts by panzercreation
TSHobbies
panzercreation's Avatar
I used it over my paint job, after giving the engine a few test runs, one of the wheel pants collected a good deal of residue and the paint has held up so far.
Old Jan 20, 2011, 02:29 PM
Brufli is offline
Find More Posts by Brufli
Registered User
Brufli's Avatar
EJ
Been following your thread w/great interest. Two questions, where you got your Stits polytone, and what you are using for a thinner for spraying and clean up? Also what time of air gun are you using for the general spraying?
Thanks a lot
Ben
Old Jan 20, 2011, 04:55 PM
EJWash1 is offline
Find More Posts by EJWash1
AMA 910957
EJWash1's Avatar
Thanks Brufli,

Quote:
Originally Posted by Brufli View Post
where you got your Stits polytone, and what you are using for a thinner for spraying and clean up?
I ordered the Polytone directly from Stits:

http://www.stits.com/store/index.html

The Polytone is already thinned for spraying. I'm using MEK for clean-up. Stits offers a how-to DVD. I have it and recommend it.

Quote:
Originally Posted by Brufli View Post
Also what time of air gun are you using for the general spraying?
I have a DeVilbiss SRI-W HVLP spot repair spray gun. I love it! Just the right size and weight for modeling.

Thanks for following along!

EJWash
Old Jan 21, 2011, 07:36 PM
Brufli is offline
Find More Posts by Brufli
Registered User
Brufli's Avatar
EJWash
Thank you for your reply. Greatly appreciated.
Ben
Old Jan 21, 2011, 11:05 PM
aerofly0610 is offline
Find More Posts by aerofly0610
Former B52H Crew Chief
aerofly0610's Avatar
any new pictures?
Old Jan 22, 2011, 11:10 PM
EJWash1 is offline
Find More Posts by EJWash1
AMA 910957
EJWash1's Avatar
No, nothing new. No shop time, so no progress.

EJWash
Old Jan 29, 2011, 06:47 AM
MickOZ is offline
Find More Posts by MickOZ
Registered User
E J Wash
Deep down I am an avid builder and have due to years of uni, work, a new family exacta have had to suppress the urge of building. My son and I had built a Dynaflight Butterfly which he has gained his wings on. I thought that watching my son fly and the odd build with him would satisfy the urge however after reading your build log this seems not to be the case. I have a sig seniorita kit in the garage that I purchased to build with my son but unfortunately he came home with an ARF “building takes too long dad”. Following your log I have enjoyed good advice and great tips I had not thought of in the past. It has encouraged me now have another kit from my favourite manufacturer (Sig) on order and am slowly stocking up on all the building tools. I will enjoy seeing your final product.
Again - great log, nice style and good advice however addictive and consuming.
Michael


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion SIG 1/5 scale Cub MJFinegan Glow to Electric Conversions 14 Jun 08, 2007 10:20 AM
For Sale Sig 1/6 scale Citabria kit. Gerald Aircraft - Fuel - Airplanes (FS/W) 1 May 28, 2006 05:34 PM
Sig 1/5 scale Piper Cub Michael in Toronto Scale Kit/Scratch Built 5 Oct 04, 2002 12:30 PM