Shop our Airplanes Products Drone Products Sales
Thread Tools
Old May 03, 2012, 10:13 PM
Runnikee is offline
Find More Posts by Runnikee
Crash and burn, huh Mav?
Runnikee's Avatar
Quote:
Originally Posted by Cabledawg1 View Post
The one scheme I dont like is on the new laser.
Where the heck is this Laser I hear people talking about?? Am I missing it somewhere?
Sign up now
to remove ads between posts
Old May 03, 2012, 11:03 PM
Cabledawg1 is offline
Find More Posts by Cabledawg1
Registered User
Cabledawg1's Avatar
Old May 03, 2012, 11:30 PM
Nikolei Zinsli is offline
Find More Posts by Nikolei Zinsli
If it's R/C, I LIKE IT!
Nikolei Zinsli's Avatar
Quote:
Originally Posted by TG43 View Post
You can cut a little off one of the ball links with an x-acto knife. That's what I did, works fine.
The rod is threaded as far as it can go into the ball link, cutting off some of the plastic wont make it thread in deeper.
RCG Plus Member
Latest blog entry: 93" AJ Laser 230z
Old May 03, 2012, 11:44 PM
TG43 is offline
Find More Posts by TG43
Registered User
TG43's Avatar
Oh, mine was hitting where there were no threads left for the ball link to go on deeper. Chopped a few mm off the ball link and cranked it on a few more turns and it was fine.
Old May 03, 2012, 11:45 PM
Doc Austin is offline
Find More Posts by Doc Austin
Team Extreme Flight
Doc Austin's Avatar
Quote:
Originally Posted by Hornetnz View Post
The rod is threaded as far as it can go into the ball link, cutting off some of the plastic wont make it thread in deeper.
Start cutting threads off the pushrod until it works. As long as you have one or two threads showing when the ball link is bottomed out, that's fine. A few times on my 48" Extras I have had to snip 1/16 off each aileron pushrod, but that's better than being too short.

Just snip 1/16 at a time. Nothing is better than having the control surface centered and the pushrods threaded all the way into the ball link. No way that will ever pull out.

Here's something funny...... I put a new fuselage on my 48" Edge. I used the same servos and pushrods. I just took them off the wreck, and I did not have to adjust them at all! It's just amazing how tight the tolerances are on these planes.
Last edited by Doc Austin; May 04, 2012 at 12:34 AM.
Old May 03, 2012, 11:56 PM
Runnikee is offline
Find More Posts by Runnikee
Crash and burn, huh Mav?
Runnikee's Avatar
Quote:
Originally Posted by Cabledawg1 View Post
Very cool. Is there a link on the Extreme Flight site to this or is it classified?
Old May 04, 2012, 12:09 AM
7oneWo1f is offline
Find More Posts by 7oneWo1f
AMF Years
7oneWo1f's Avatar
I want that prop.
Old May 04, 2012, 12:15 AM
Nikolei Zinsli is offline
Find More Posts by Nikolei Zinsli
If it's R/C, I LIKE IT!
Nikolei Zinsli's Avatar
Do I really have to goto work tomorrow morning? I'm so close!
RCG Plus Member
Latest blog entry: 93" AJ Laser 230z
Old May 04, 2012, 03:59 PM
jwilliamsrc is offline
Find More Posts by jwilliamsrc
Team Extreme Flight, JR, BandE
Quote:
Originally Posted by EXTREME FLIGHT View Post
There is no magic pill to learning 3D, in fact there is only one way to learn and that is to practice, practice and..............practice some more. Fly with a purpose and focus on individual maneuvers. There are so many Internet resources available to assist you and it is far simpler to learn these days. Back when my friend Russelland I learned 3D in 1994 there were no instructional videos, Internet forums, heck there weren't even any 3D planes or ARFs available. We had to build from kits and scratch build larger control surfaces and talk to guys like Quique, Mike McConville, Frank Noll and a handful of others who were key players in the development of 3D and pick their brain about what they were doing. Lots of trial and error, frustration and disappointment, but we wanted it bad and eventually we persevered. What I am trying to say is use the resources you have available and practice as much as possible. The airframes available today are light years ahead of what we had in 1994 and are a direct result of years of trial and error and experience. Any of the 48" aircraft are more than capable of teaching you all the moves from the most basic to the most advanced. We have provided you with the tools, the rest is up to you.
I doubt many will realize the amount you said in those 10 sentences.
I am amazed how some think by talking, watching, reading and whatever else will help them more than practicing. One hour of practice is worth more than 10 hours of the other stuff.....burn batteries/fuel often then start all over. Learning 3D is one thing, getting good at it and staying up on new maneuvers is another.
Jeff
Old May 04, 2012, 05:28 PM
stgdz is offline
Find More Posts by stgdz
Volts>amps
stgdz's Avatar
Put it this way,

I learned to Harrier on an mxs.


For all intents and purposes this would be the last plane you should learn on. I went extra-edge-mxs. I would wing rock like no other on the edge. I really liked the looks of the mxs so I got that.


All that while I was just practicing over and over again and finally got it with the mxs. Three different air frames. I would have probably gotten their faster if I stuck with one but I alike the looks of each.


There really is no silver bullet for 3d air frames.
Old May 04, 2012, 06:49 PM
TG43 is offline
Find More Posts by TG43
Registered User
TG43's Avatar
Here's some pretty awful flying. Having fun though!

48" Extreme Flight Extra 300EXP (5 min 20 sec)
Last edited by TG43; May 04, 2012 at 11:56 PM. Reason: fixed vid
Old May 04, 2012, 07:52 PM
doc993 is offline
Find More Posts by doc993
Registered User
doc993's Avatar
The Laser is in a secret under ground development lab as we speak.
Old May 04, 2012, 08:03 PM
stgdz is offline
Find More Posts by stgdz
Volts>amps
stgdz's Avatar
Quote:
Originally Posted by doc993 View Post
The Laser is in a secret under ground development lab as we speak.
A couple of things

1) reorient your antennas, they are going the same way and you want to have them perpendicular to one another. You really should mount it way back behind the canopy.

2)Do you have an adapter between the deans and the XT60 connector? Thats going to raise the resistance and thus lower the power level.
Old May 04, 2012, 09:43 PM
Nikolei Zinsli is offline
Find More Posts by Nikolei Zinsli
If it's R/C, I LIKE IT!
Nikolei Zinsli's Avatar
Do you guys epoxy velcro to your packs or just find sticky back velcro?
RCG Plus Member
Latest blog entry: 93" AJ Laser 230z
Old May 04, 2012, 10:10 PM
doc993 is offline
Find More Posts by doc993
Registered User
doc993's Avatar
Yes I will reorient the antenna, yes the adapter is just for bench tests,I do not like deans pins.I also cannot fly till I get the recommended prop the one I have is a 13 / 8,Then the covering flaw needs to be addressed, ama number and ident tags ext.This was a very smooth build ,and I'm really enjoying it.The laser is so cool.I saw Leo fly many times at Oshkosh. He was so precise and smooth.I can't wait to see the team pilots ring this one out.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Article Extreme Flight 48" Vanquish Review matchlessaero 3D Flying 71 Jan 03, 2016 09:39 PM
Discussion Extreme Flight RC Extra 300E sd2602 3D Flying 75 Jan 30, 2012 05:04 AM
For Sale Extreme Flight 50cc Extra 300 RTF Flyinrazrback Aircraft - Fuel - Airplanes (FS/W) 2 Jan 24, 2009 07:11 PM