CNC cut AG11 4.75 inch formica template - RC Groups
Thread Tools
This thread is privately moderated by juzwuz, who may elect to delete unwanted replies.
Feb 28, 2009, 01:08 AM
Trader Rating: 66
Registered User

CNC cut AG11 4.75 inch formica template

A while back, I cut two formica AG11 airfoil templates (upper and lower surface) with a 4.75 inch chord when I was testing my cnc router. Anyone interested in a set for $1 shipped in the US?
Sign up now
to remove ads between posts
Feb 28, 2009, 01:26 AM
Trader Rating: 0
Registered User
to help with your testing, how much for a full set for a Bubble Dancer to help my next project along. I have been wishing for a router...

Steve in Spokane
Feb 28, 2009, 02:14 AM
Trader Rating: 66
Registered User
I thought someone could possibly use these templates before I just toss them into the's spring cleaning time for me.

I was testing various feed rates, spindle speeds, and bit sizes for cutting formica. It's a bit tougher than cutting wood or foam but not too bad once things are set up. For a while, I was trying to use a 0.032" endmill and I must have broken at least 3.

Anyway, if you have some CAD drawings for the bubble dancer I could take a look to see if they would fit on my router. I have a smallish router with about 17" by 23" of travel.
Feb 28, 2009, 08:58 AM
Trader Rating: 47
Team Horizon Pilot :)
Ill take them
Latest blog entry: cr
Mar 03, 2009, 01:56 AM
Trader Rating: 66
Registered User
Deal pending with Gavin for the original templates plus some Supra wing templates and a 9inch AG04

Deal pending with alan7037 for Supergee2 and Bubble Dancer wing templates.

Deal pending with raed5 for Supergee2 templates.

Deal pending with Ric Duley for Bubble Dancer templates.
Last edited by juzwuz; Mar 07, 2009 at 03:55 AM.
Mar 03, 2009, 11:39 AM
Trader Rating: 112
One Idiot is plenty...
Dbox's Avatar
Juzwuz,can You make the templates on order?
Say different cords and foils?
Mar 06, 2009, 02:19 AM
Trader Rating: 66
Registered User
Here are some CAD pictures of the wing airfoil templates for the Supergee2, Supra, and Bubble Dancer. I'll cut them out this weekend.
Mar 06, 2009, 10:15 AM
Trader Rating: 111
Almost a Pilot
Mauilvr's Avatar
I'd be very interested in a set of those Bubble Dancer templates.

Sending PM.
Mar 07, 2009, 04:02 AM
Trader Rating: 66
Registered User
Looks like there is quite a bit of interest in templates. I can cut them to order just as long as they fit on my 17" by 23" router. I've got plenty of formica on hand but I can also cut other materials.
Mar 12, 2009, 02:40 AM
Trader Rating: 66
Registered User
Templates for alan7037 and Ric Duley have shipped.

Templates for raed5 will ship tomorrow now that echeck has cleared. Templates have shipped for raed5.

Templates for Gavin have shipped.
Last edited by juzwuz; Mar 13, 2009 at 04:27 PM.
Mar 14, 2009, 03:44 AM
Trader Rating: 66
Registered User
Since the original templates have sold and all additional templates have been shipped I'll go ahead and close this thread. I'll start a new ad. Thanks!

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
CNC cut cores CLARK Y 1.8 inch chord steelhead Scratchbuilt Indoor and Micro Models 37 Mar 28, 2005 12:24 PM
a 24 inch hot wire setup to cut 1/4 inch foam slices enigmabomb Electric Plane Talk 1 Nov 18, 2003 01:11 AM
DMA Flea w/ 4.75 x 4.75 APC Prop $48.00 phoneguy Aircraft - Electric - Airplanes (FS/W) 4 Jul 27, 2002 12:07 AM
Rc-2400 $4.75, Rc-3000hv $5.80, Hhr150aa $1.70 jmpratt Aircraft - Electric - Airplanes (FS/W) 0 May 03, 2002 03:37 PM