How can I tell if my prop balancer is running true? - RC Groups
Shop our Airplanes Products Drone Products Sales
Thread Tools
Feb 12, 2009, 11:22 PM
I'm a Registered User

How can I tell if my prop balancer is running true?

I made my own magnetic prop balancer. I bought one of those "finger tip" balancers that's basically a threaded shaft with points on the ends, and come cones to center the prop. I then suspended it between some rare earth magnets. It seems to work well with props down to my 4" GWS's. Now however, I'm trying to balance an EDF rotor and I'm having a heck of a time with it. It doesn't seem to be consistently out of balance, but I know it's not slipping and everything is tight. The rotor is so thick I'm only catching a few threads on the balancer shaft with the cones, and I think that might be causing a wobble. I'm also wondering if the drag of the points on the magnets might be throwing it off(it takes some extra magnets on the back side to hold the heavy rotor. Is there a way to tell if the balancer is out of true or if I just suck at balancing rotors? Thanks.
Sign up now
to remove ads between posts
Feb 12, 2009, 11:46 PM
Don't watch this...
CooHead's Avatar
Beats me...but curious of the replys your question requests.
But tell me. Since you have balancer, I take it you do balance your props.
How often are they out of balance and how much does it take to get them into balance?
I've been flying for years. Have had to have gone through at least 100 props to date. Never a one has been balanced. I alwasy wondered about that. Like how much difference is there and/or how much "better" is a "balanced" prop?
I'm no expert 3D or IMAC guy. Just the weekender that breaks props all the time on harrier landings

Feb 13, 2009, 12:30 AM
Registered User
I balance all my props. Of course I use rather large props; 10" - 11" for my Slow Stick and since it's my AP plane I want to reduce all the vibration I can.

I use small pieces of electrical tape on the back side of the prop to balance it. I just move it toward the hub or tip as required to get it balanced. Takes about 30 seconds to balance one. However, my Slow Stick uses a low KV motor, too.

Other people sand away some material on the heavy tip, add a bit of clear fingernail polish, or a little dab of glue to balance it. I don't like any of those methods because they are so permanent. With the tape, if the prop needs balancing again due to a prop strike on pavement, for example, just peel the tape off and move it to a new location.

Below is a very simple prop balancer that didn't cost me anything. However I have now upgraded it with one of those finger balancers Jeff mentioned.

Feb 13, 2009, 12:46 PM
Xpress..'s Avatar
It's pretty important to balance props, especially with an electric power system. An unbalanced prop will rob your motor of power and effeciency, so instead of you getting, oh lets say 200 watts with a balanced prop, you might only get about 180 or so watts with an unbalanced prop. And instead of 15 minutes per flight, you might only get 10-12 minutes.
Feb 13, 2009, 02:15 PM
↓↘→ + (punch)
theKM's Avatar
unbalanced props represent wasted watts, and increased wear on motors

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion how can I tell if my CC45 esc is damaged? tukkus Castle Creations 2 Nov 05, 2008 10:54 AM
Discussion Can't tell if my motor's running or not NoFlyZone Beginner Training Area (Aircraft-Electric) 13 Oct 12, 2006 02:48 PM
Question How can I tell if my CC25 is the new 3 amp BEC version? rcmann Castle Creations 20 Feb 06, 2006 10:57 PM
How can i tell if my gws transmitter a neg or pos shift? lift off Radios 20 Mar 21, 2005 01:10 AM
How can I tell if my NiMH cells are charged? Sting2XC Batteries and Chargers 3 Feb 02, 2005 07:59 PM