xinte's blog - RC Groups
xinte's blog View Details
Posted by xinte | Jun 25, 2018 @ 05:32 AM | 1,866 Views
JMT Crazybee F3 Flight Controller OSD Current Meter 4 IN 1 5A 1S Blheli_S ESC Compatible Frsky / Flysky Receiver for Whoop Drone
Frsky or Flysky Receiver optional, Please choose the item according to your transmitter.

https://www.xt-xinte.com/h-product-d...oods_id=486690

Specifications:
Firmware: Betaflight_3.3.0_Crazybee
MCU: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000(SPI connection)
Power supply: 1S battery input (DC 3.5-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Flysky receiver with telemetry AFHDS/AFHDS-2A compatible
Built-in Betaflight OSD(SPI Controll)
Built-in Current meter (Max 14A,could be modified to 28A by replace resistor)
Built-in 5V 0.8A BEC with LC filter
Built-in voltage detection
BLHELI_S pass-through Ready
Heading LED Ready
Board size: 28.5 * 28.5MM
Board weight: 3.5 g

ESC parameters:
Power supply: 1S LiPo/LiPo HV (4.2v/4.35v)
Current: 5A continuous Max 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_L_5_REV16_6.HEX
Motor connector: JST PH1.25 3pin
Signal Support: Dshot150/Dshot300/Dshot600/Oneshot125/Multishot/PWM

Receiver parameters:
SPI BUS receiver
Frsky D8/D16 switchable
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
No ground interference ( Transmitting and receiving 1 m from the ground): 300m
Failsafe support

Package Included:
1 x Crazybee flight controller ESC Flysky/Frsky receiver
Posted by xinte | Jun 14, 2018 @ 10:22 PM | 1,647 Views
Beecore VTX Brushed Flight Controller for Tiny Whoop Built-in Betaflight OSD and 25mw VTX with Smartaudio

https://www.xt-xinte.com/Beecore-VTX...o-p527543.html

The tiny whoop style Brushed flight controller built-in Betaflight OSD and 25mw VTX with Smartaudio is coming now. Best for Kingkong Tiny6/6x/7/7x .
Specifications:
MCU: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000(SPI connection)
Power supply: 1S battery input (DC 3.5-4.35V)
Built-in Betaflight OSD(SPI Controll)
Built-in 5.8G 25mw 40ch vtx
Smartaudio function ready
Heading LED Ready
Mount hole distance: 26mm * 26mm
Board size:29mm*29mm
Board weight: 4.0 g

Features:
With 4 large current NMOS transistors, operating current of up to 10A each
Built-in OSD(Using F3 MCU controls OSD over SPI bus in DMA mode)
Smartaudio ready, you can change the VTX channels by your radio sticks
PPM/SBUS/IBUS/DSM2/DSMX ..etc protocol receiver compatible
Best for Tinywhoop style brushed frame , perfect flight controller replacement for Kingkongrc/LDARC Tiny6/6x/7/7x/8/8x
Posted by xinte | Jun 13, 2018 @ 03:31 AM | 1,807 Views
JMT Crazybee F3 Flight Controller OSD Current Meter 4 IN 1 5A 1S Blheli_S ESC Compatible Frsky / Flysky Receiver for Whoop Drone
Frsky or Flysky Receiver optional, Please choose the item according to your transmitter.

Specifications:
Firmware: Betaflight_3.3.0_Crazybee
MCU: STM32F303CCT6 (72MHZ, 256K FLASH)
Sensor: MPU-6000(SPI connection)
Power supply: 1S battery input (DC 3.5-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Flysky receiver with telemetry AFHDS/AFHDS-2A compatible
Built-in Betaflight OSD(SPI Controll)
Built-in Current meter (Max 14A,could be modified to 28A by replace resistor)
Built-in 5V 0.8A BEC with LC filter
Built-in voltage detection
BLHELI_S pass-through Ready
Heading LED Ready
Board size: 28.5 * 28.5MM
Board weight: 3.5 g

ESC parameters:
Power supply: 1S LiPo/LiPo HV (4.2v/4.35v)
Current: 5A continuous Max 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_L_5_REV16_6.HEX
Motor connector: JST PH1.25 3pin
Signal Support: Dshot150/Dshot300/Dshot600/Oneshot125/Multishot/PWM

Receiver parameters:
SPI BUS receiver
Frsky D8/D16 switchable
Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8ch(AFHDS) or 14ch(AFHDS-2A)
No ground interference ( Transmitting and receiving 1 m from the ground): 300m
Failsafe support

Package Included:
1 x Crazybee flight controller ESC Flysky/Frsky
Posted by xinte | Jun 13, 2018 @ 02:56 AM | 1,604 Views
AT10 / AT10II online upgrade

https://www.xt-xinte.com/RadioLink-A...r-p133765.html


The latest AT10(AT10II) version V1.3.7 firmware upgrade on Sept. 27, 2017.



Download of bin_af90_V1.3.7 .(AT12S).mac : https://mega.nz/#!NZ9VSbKJ!j74qjMyzx...CYwY2jbHsXhC4I



Download of bin_af90_V1.3.7 .(AT12S).bin : https://mega.nz/#!Jd0TWaza!kQb350oUH...zl8qk2Qg-c0ebc




Improvement:

1. ADD: Add Throttle Position alarm funtion, transmitter will warning if throttle is not at the lowest position when power on.
You can setup Throttle Position alarm funtion on or off in SYSTEM menu



/************************************************** ************************************************** ************************************************/

The latest AT10(AT10II) version V1.3.0 firmware upgrade on Sept. 7, 2017.



Download of bin_3c57_V1.3.0 .(AT12S).mac : https://mega.nz/#!tB1yDIib!IyG0A5bBs...qjraLQ6PVRuYXs


Download of bin_3c57_V1.3.0 .(AT12S).bin : https://mega.nz/#!lE1mzDJJ!4oSro5cC7...6lfayMA8pN6jvA




Improvement:

1. Improved: Joysticks adds more filtering.
2. Add: Add CAR and BOAT model type.
3. Add: AT10/AT10II will alarm if throttle do not at the bottom when power on.
4. Add: RSSI signal strength pass through on a spare channel, can setup CH5 to CH12 as the RSSI signal output channel.
5. Change: the RSSI signal strength display change from figure to percent, 100% show the strongest RSSI signal.



/***********...Continue Reading
Posted by xinte | Jun 13, 2018 @ 02:53 AM | 1,461 Views
T8FB 8CH transmitter upgrade doc

https://www.xt-xinte.com/RadioLink-T...e-p133821.html

T8FB 8 channels transmitter upgrade file download: https://mega.nz/#!1E8XXYxA!TsuM02c8c...Ys-OBuUevD6tqM



Include:



1. T8FB Upgrade Driver: for WIN7 & XP、WIN8 & wWIN10



2. T8FB Upgrade Tools & T8FB Latest Frimware



3.T8FB Parameter setup tool by Phone / Computer



4.T8FB User manual







T8FB Parameter Configuration:Guidance: http://radiolink.com.cn/doce/t8fb-pa...iguration.html



T8FB Firmware Upgrade or Model Type Change Guidance: http://radiolink.com.cn/doce/t8fbchangemodetypes.html
Posted by xinte | Jun 13, 2018 @ 02:51 AM | 1,461 Views
CB86-PLUS Balance Charger firmware upgrade document





The latest version V2.4 is updated on July.25th,2016



CB86-PLUS-V2.4.bin VUP Download : https://mega.nz/#!Yd8BnboI!8toYiGuVd...si-fkybftVtiUU

CB86-PLUS-V2.4.mac VUP Download : https://mega.nz/#!8Y9B2bBZ!_SBWMsr_e...DekHPuBkdB8uys



CB86PLUS upgrade steps :



1. Put your CB86PLUS via USB cable to your computer.



2. Connect CB86PLUS to a suitable DC power supply with 10.5-15V output voltage and minimum of 15A output current.



3. It appears like disc on your computer.



4. Format original files(Format original file means format the transmitter files when you bought. For example, your CB86PLUS is the version V1-8, you want upgrade to the version V1-9. Then you have to format the file of V1-8 , and then copy the file of V1-9. So the file V1-8 is the original file).



5. Copy upgrade file.



6. Put USB cable off.






The differences between mac and bin files.



(1)File mac for new version CB86PLUS which can upgrade by computer with win7, win8, XP and APPLE.



(2)File bin for old version CB86PLUS which only can upgrade by computer with win7, XP.





The differences between new version and old version CB86PLUS.



(1 ) Appear hint “format files”, display shinning when connect CB86PLUS to computer.



(2)Without any hint, only display is on constantly when connect CB86PLUS to computer.



...Continue Reading
Posted by xinte | Jun 13, 2018 @ 02:48 AM | 1,470 Views
AT9 / AT9S Firmware Upgrade V1.7.5 (AT12S)_c0f0.dfu is updated on Oct.10, 2017



Download of V1.7.5 (AT12S)_c0f0..dfu: https://mega.nz/#!MQVEXbCK!1tLc3boHn...b5tnDPBbZ6C0ng



Improvements:



1. Add THR-HOLD function in MULTIROTOR model.



/************************************************** ************************************************** ******************************/

AT9 / AT9S Firmware Upgrade V1.6.6 (AT12S)_821c.dfu is updated on Sept.7,2017



Download of V1.6.6 (AT12S)_821c.dfu: https://mega.nz/#!JUFECZxT!bNvAWrA3e...-_kVgHTxhT7was


Improvements:



1. Improved: Joysticks adds more filtering.
2. Add: AT9/AT9S will alarm if throttle do not at the bottom when power on.
3. Add: RSSI signal strength pass-through on a spare channel, can setup CH5 to CH12 as the RSSI signal output channel.
4. Change: the RSSI signal strength display change from figure to percent, 100% show the strongest RSSI signal. /************************************************** ************************************************** ******************************/


AT9 Firmware Upgrade Diver Document Download——June 6,2015



AT9 remote control upgrade driver for WIN7/WIN8/WIN10/XP system: https://mega.nz/#!VNl2BAAC!_PdH-5oYo...Lqsy6ACECjGAmM



Firmware upgraded for PC (XP system) download: https://mega.nz/#!IAVxDBQB!I-VgEP_it...E6FExulTeecEmc



Firmware upgraded for PC (WIN7/WIN8/WIN10 system) download: https://mega.nz/#!...Continue Reading
Posted by xinte | Jun 13, 2018 @ 02:44 AM | 1,466 Views
Radiolink AT9 --- USB data backup copy function introduction


Operation video:copy data by USB for AT9(in Chinese)

http://v.youku.com/v_show/id_XMTUwMj...rom=s1.8-1-1.2



Radiolink AT9 data copy by USB V1.0 system download :

https://mega.nz/#!EEsnFIiA!b0fCMzoqZ...pGyUgATG_l40nY





Note 1: When use USB cable connect to AT9, it’s better to reopen "Radiolink AT9 USB data copy system V1.0".

Note 2: Before use "Radiolink AT9 USB data copy function", run "ctlUpdate_step1.bat" first.

Note 3: When the first time to open “Radiolink AT9 USB data copy V1.0 system ”, need to run as administrator.

Note 4: There need to have “DD” sound when write data into transmitter, there must be have something wrong with the copy system if doesn’t have “DD” sound, please reopen "Radiolink AT9 USB data copy system V1.0”, return on the AT9, reconnect the USB cable.



Steps:

1. AT9 have to upgrade to V1.3.3 first if you need use the copy function. The instructions how to upgrade the firmware, please refer to this video.

RadioLink AT9 Firmware Update (8 min 21 sec)




2. Turn on transmitter, then connect to computer through the USB cable.



3.Turn on USB data copy function in MODEL SEL. menu: Choose BASIC MENU-> MODEL SEL.->COPY→PC:ON



4. Open “AT9 USB data copy system V1.0”.



5. Click”CONNECT”, green light on means connect successfully.



6. Read the AT9 data: click “...Continue Reading
Posted by xinte | Jun 13, 2018 @ 02:09 AM | 1,438 Views
Mantis85 85mm 5.8G FPV Micro Racing Drone Quadcopter BNF 600TVL HD Camera VTX with Double Antenna 3 Inch 40CH Mini Video Goggles
https://www.xt-xinte.com/Mantis85-85...s-p524813.html
Package include:
1 x Happymodel Mantis 85 FPV Racing Drone BNF
1 x JMT LST-009 Double Antenna 5.8G FPV Goggles
1 x Flysky FS-i6 6CH 2.4G AFHDS 2A LCD Transmitter

This is RTF Version, Ready to Fly, All Assembly.

Drone Detail:


Item Name:Mantis 85 Micro FPV RACING DRONES BNF No Remote Controller
Size:100mm*100mm*25mm
Weight: 52g( battery not include)
Flight controller: Super_S F4 Flight controller built-in Betaflight OSD
Motor: Happymodel SE1102 KV9000 brushless motor
Propeller: 1935 3-blades propeller
Camera: 600TVL HD CMOS 1/4inch
VTX: 5.8g 25MW 48CH NTSC/PAL Video transmitter
Battery: 7.4V 400mah 30C lipo battery
OSD: Betaflight OSD
Firmware of Flight controller :Betaflight 3.2.0
Flight time : 4minutes
Buzzer Ready

Features:
- 3K full carbon fiber bottom plate set up with CNC aluminum alloy Stiffeners
- Extremely light and more powerful
- STM32F405RGT6 MCU+ BLHELI_S ESC make your Operating feel more stabile and silky
- Adjustable Angle of Camera
- Jaw-dropping flight performance
- Betaflight support
- Acro mode / Air mode /Angle mode support
- Built-in OSD(Using F4 MCU controls OSD over SPI bus in DMA mode)
- OSD Configuration has been include in BETAFLIGHT GUI
- Radio Stick to control PID Tunes
- BLEHELI_S pass-...Continue Reading
Posted by xinte | Jun 13, 2018 @ 01:40 AM | 1,433 Views
Package include:
1 x Snapper7 Brushless Micro 75mm Racer Drone
1 x JMT LST-009 Double Antenna 5.8G FPV Goggles
1 x Flysky FS-i6 6CH 2.4G AFHDS 2A LCD Transmitter

This is RTF Version, Ready to Fly, All Assembly.

Drone Detail:


Specifications:
Mode Name: Snapper7
Wheelbase: 75mm
Size: 98.5mm*98.5mm*36mm
Drone Weight: 28g(without battery)
Features:
Betaflight support , multi flight mode: ACRO/AIR/ANGLE
Powerful Brushless motor and Smooth ESC
CNC aluminum alloy propeller guard
Betaflight OSD support ,easy to get RSSI , Voltage and other info from your goggles
Adjust the settings and the PID of the flight controller via OSD
Full telemetry function ready
Head lights ready
Camera angle adjustable
Real Bind and Fly version
FPV Goggles Detail:

Highlight:
Double Antennas
Built-in 3.7V 1200mAh Battery
Support a key search frequency
RaceBand 40 channel Auto-Searching
Real-time video return 5.8G FPV Receiver


Feature:

● Small size and light weight;
● Low power consumption, Working current 300~330mA;
● Double antenna reception to make the signal more stable;
● RaceBand 40 channel, Auto-Searching;
● 3.0 Inch 480*320 dot high brightness LCD screen;
● Built-in super sensitiveness 5.8GHz 40ch receiver, especially with RaceBand;
● Built-in 3.7V/1200mAh high-capacity Li-ion polymer Battery;
● Universal USB charging interface;
● Real-time video return, Very low time-delay;
● Bilingual menu in support of Chinese and English;
● Support external video signal input;
● Support AV signal output (Connect external DVR);



Posted by xinte | Jun 12, 2018 @ 04:25 AM | 1,202 Views
BEECORE Lite Brushed Flight Control Silverware Firmware Bayang Agreement for FPV Racing Drone Quadcopter

SPECIFICATIONS:
CPU: STM32F030
Six-Axis: MPU6050
Receiver module:XN297LBW
ESC: All FETs are rated at 12A maximum. Support 6x15mm/7x20mm/8x20mm/8.5x20mm etc motors.
Size: 26mm x 26mm, fully compatible with the Inductrix quad frame and mounting pattern
Firmware : Silverware
Receiver protocol: Bayang protocol
Power Cable: 50mm, with JST-PH 2.0 connector,
Weight: 2.7g

Features:
Support level mode and acro mode. Also it has the ability to change settings for custom builds, or to adapt to personal preferences by stick gestures.
Designed to work with current Tiny Whoop or Blade Inductrix frames
Built in Bayang protocol native receiver, compatible with almost radio transmitter with deviation firmware or deviation compatible transmitter module
The flight controller board comes pre-flashed with Silverware firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector.

Compatible radio transmitter:
BETAFPV TX01 radio transmitter
Radio transmitter of toy drone like JJRC H67, Eachine E011 etc, that using the Bayang protocol
Jumper T8SG radio transmitter
MTX9D multiprotocol module (Suit for Frsky Tanaris QX7 X9D X9D Plus X12S, Flysky TH9X, Turnigy 9XR/9XR PRO)
MTXI6 multiprotocol module(Suit for Flysky i6, i6S, I6X, I10)
Other 4in1 multiprotocol module that support the Bayang protocol
Posted by xinte | Nov 24, 2017 @ 12:02 AM | 3,234 Views
Help!Need reviews for this drone
Here is the 450 DIY RC Drone,https://www.xt-xinte.com/Full-Set-RC...r-p134024.html
Seek reviews for this drone,I can send the drone for free.
Welcome to contact me for cooperation,thanks!
Posted by xinte | Nov 23, 2017 @ 11:18 PM | 2,769 Views
Professional JMT 2.4G 8CH 310 330 360 Mini RC Quadcopter ARF RTF Unassemble DIY Drone FPV Upgradable with Radiolink Mini PIX M8N GPS Altitude Hold

https://www.xt-xinte.com/2-4G-8CH-31...d-p435660.html

Package included:
F02471-M F330 Quadcopter:
F330 Frame Kit * 1,
1400KV A2212 10T Brushless Motor * 4,
Simonk firmware 30A ESC with BEC 5V * 4,
8045 Plastic CW CCW Propellers * 2,
Radiolink MINI PIX + MINI GPS * 1,
GPS Folding Antenna Mount * 1,
Radiolink T8FB Remote controller * 1,
11.1V 2200MAH 25C Lipo Battery * 1,
B3PRO Charger * 1,
Buzzer Alarm * 1,
Accessories bag * 1

F14892-N 360mm Quadcopter:
X4M360L Glassfiber Frame Kit * 1,
920KV CW Brushless Motor * 2,
920KV CCW Brushless Motor * 2,
Simonk firmware 30A ESC with BEC 5V * 4,
8443 Carbon Fiber Propeller Self-locking * 2,
Radiolink MINI PIX + MINI GPS * 1,
GPS Folding Antenna Mount * 1,
Radiolink T8FB Remote controller * 1,
11.1V 3300Mah 25C Lipo Battery * 1,
B3PRO Charger * 1,
Buzzer Alarm * 1,
Accessories bag * 1

F14891-M 310mm Quadcopter:
X4M310L Glassfiber Frame Kit * 1,
1400KV A2212 10T Brushless Motor * 4,
Hobbywing XRotor 20A ESC * 4,
8x4.5 2-Blade Propellers * 2,
Radiolink MINI PIX + MINI GPS * 1,
GPS Folding Antenna Mount * 1,
Radiolink T8FB Remote controller * 1,
11.1V 2200MAH 25C Lipo Battery * 1,
B3PRO Charger * 1,
Buzzer Alarm * 1,
Accessories bag * 1


Function:
1. Forward/backward,Sideward flight,Turn left/right,Up/down,Hover,One Key Taking Off,Self-...Continue Reading
Posted by xinte | Nov 23, 2017 @ 10:03 PM | 1,028 Views
Hello,Everyone
Does anyone need DIY RC Drone User Manual or video? I happen to get some,if anyone need,please contact me.
F02192 y (3 min 56 sec)

Email :admin@xt-xinte.com
skype:xintegroup