TINGW's blog View Details
Posted by TINGW | Oct 09, 2017 @ 02:30 AM | 1,652 Views
Hot sale transmission DYS mi200 normal version and pigtail version:

Basic Data:
Transmission Frequency:5.8Ghz
Transmission Power:25-200MW
Frequency point:40CH
Transmission distance:1000M
Input voltage:5V
Antenna connector:SMA Hole
Working current:500mA/5V
Operating temperature:-10-85℃
Video Format:NTSC/PAL
Video Broad band:8M
Size: L23*W22*H8mm

More detail is you can visit: http://www.bonroytech.com/views.asp?hw_id=431

The video is: https://youtu.be/_LILKjiv7m0?t=13
Posted by TINGW | Sep 25, 2017 @ 02:29 AM | 1,730 Views
Item name: Fire
KV: 2100KV/2300KV/2600KV
Pull: 1280g/ 1450g/ 1200g
Motor Size:Φ27.7x17.7
Battery: 3-6S Lipo
Weight: 32.38g
Imported ISC bearing
0.1mm laminations
N54 magnets
M5 hollow shaft

Item: Storm
KV: 2300KV/2500KV
0.1mm laminations
Imported ISC bearing
N54 magnets
M5 hollow shaft
Motor Dimensions(Dia.*Len): Φ27.7x18.7mm
Weight (g): 33.73g
No.of Cells(Lipo): 3-6S
Max Continuous current(A): 29.3A
Max Continuous Power(W): 468.8W
Internal resistance: 0.04

Item name:Thor
KV: 2200KV/2500KV/2700KV
Motor Dimensions(Dia.*Len): Φ29.7x18.7mm
Weight (g): 37.45g
No.of Cells(Lipo): 3-6S
Max Continuous current(A): 38.3A
Max Continuous Power(W): 612.8W
Internal resistance: 0.04

Item name:Mars
KV: 2400KV/2750KV
Motor Dimensions(Dia.*Len): Φ28.5x18.7mm
Weight (g): 34.36g
No.of Cells(Lipo): 3-6S
Max Continuous current(A): 34.5A
Max Continuous Power(W): 574.4W
Internal resistance: 0.04
Posted by TINGW | Sep 22, 2017 @ 02:48 AM | 2,411 Views
You can order it from :http://www.bonroytech.com/views.asp?hw_id=416

Item name: F4 PRO
Size: L42 * W36mm
Hole distance: 30.5*30.5mm
Net weight: 11.2g (exclude wire)

* OMNIBUSF4 firmware
* Master STM32F405 GRT6, refresh rate up to 8K
* PCB 3OZ copper enhance current stability and cooling fast
* 5V 3A BEC output
* Exposed pad for easy soldering
* Compatible with all ESCs, as well as DYS 4-in-1 esc without soldering
* Integrated OSD, no need to flash firmware additionally,debug OSD via BF ground station.
* Integrated current meter to monitor the real-time power consumption
* Adjust the PID by OSD via remote control
* Adjust the VTX via open ports such as power, frequency band, frequency point (Note: The VTX should have this function like TBS one and the upcoming DYS VTX.)
* DYS F4 flight control with 4 damping balls reduce the vibration to make it fly stably.
* 2-6s lipo support
* Net weight: 11.2g (exclude wire)
* Size: L42 * W36mm, hole distance: 30.5*30.5mm
* Gyro: MPU6000
*3.3 V Voltage output
* Include PPM VTX and RSSI VTX
Posted by TINGW | Sep 22, 2017 @ 12:38 AM | 1,879 Views
Know more detail by this link:http://www.bonroytech.com/search.asp?action=search

*X160 is the micro racer for FPV hobbyist. It is a high-integrated product with highly flexible control. *Equipped with motor 1104-4000KV, propeller 3x2 as well as the popular BLheli 10A esc (Oneshot support). Flight range of remote control more than 1000 meters.
*To gain the quality and real-time shoot for FPV, X160 also combines 5.8G 32CH 200mW transmitter(the switch can shift between 20mW and 200mW) with 1/3''CMOS lens, which supports 127 or wider 160 shootings and every moment brings you the exciting FPV experience.

*This latest V3 with OSD for the video, the real-time status will be returned back to the display. Flight control SP F3 flash with CleanFlight, just connect the battery, receiver and set the remote control to use.

Brand: DYS
Item name: X160 V3 RC Micro FPV Racer
Wheel base: 160mm
Frame size: 148mm(L)x131mm(W)x41mm(H)
Propeller: 3020 propellers
Motor: 1104-4000KV
Camera: FOV127 (160D)
ESC: 10A ESC with BLHeli firmware (support oneshot)
Antenna: 5.8G mushroom antenna
Flight controller: SP racing F3
With OSD
Weight: 143g (included motor, ESC, and propeller, without battery)
Battery: recommend 3S 800-1000mah (not included)
Flight range of remote control: more than 1000 meters
Combines 5.8G 32CH 200mW Transmitter with 1/3" CMOS Lens, supports 127 or wider 160 degree shooting.
Four frame arms integrated 10A high speed ESC
Receiver and remote control not included
Posted by TINGW | Sep 21, 2017 @ 10:42 PM | 1,620 Views
Six color for your choice: http://www.bonroytech.com/views.asp?hw_id=418
Item name: ELF - 83mm micro brushless drone
Motor: BE1102-10000KV
ESC: 4-in-1 BLheli_S F10A Dshot
Prop: 1.7 inch
FC: F3
VTX: 25mW 40CH
Lipo: 2s 600mAh
Basic Info:
Wheel base:83mm
Weight:80g (battery included)
ESC:4 in 1 Blheli_S Dshot F10A
Prop: Micro 5 blades prop
VTX: 5.8G/40CH/25MW
VTX distance:300M
Lipo: 2S 600Mah
Flight time: Around 6 minutes
Camera:1.8mm 170(no microphone)
Below is the flying video for you to review:
Indoor flight of DYS Elf 83mm Micro Drone. (1 min 29 sec)

Posted by TINGW | Sep 14, 2017 @ 10:27 PM | 1,710 Views
Item Name: ARIA 35A

Weight: 4.37g(exclude the wire)

Input voltage: 3-6s Lipo

Size(mm)L*W: 32*16*5

Firmware : BLHeli_32


With 32bit ARM Cortex MCU STM32F051 48MHZ micro processor, throttle 2048 resolution ratio,strong anti-interference capacity.

Built-in sensor can be reaction of temperature,output power,output current etc,also programmable for protection.

Support Blheli_32 firmware,can use the signal wire to upgrade the firmware or change the configuration on line.

Current Meter to help show current indication of OSD

With USB linker can be programmable throttle setting like support positive and negative,two way mode,FPV 3D mode,motor speed,braking ,PWM frequency, inlet angle speed setting, onboard RGB LED for customize color, Beep etc.

It use the self-adaption control system,can go automatic with the all kind of the motor in the market,at the mean time it support up to 500HZ PWM,oneshot 125,oneshot 42,Multishot and Dshot 150/300/600/1200.

With special optimize in multi-axis,the motor can launch smoother in a good throttle curve, fast response,great power, and highly support the multi-axis,fixed-wing and helicopter.

The twisted-pair signal wire can lower the crosstalk inside cooper wire when it transfer,which will make the flight more stable.

MCU hardware,Driver circuit ,Mosfet will come with double voltage protection.

To adopt the new process MOSFET of low internal resistance, will help increase resistance to flow. Also,the professional MOS driver chip makes the best efficiency.

Mosfet is covered with aluminum sheet for cooling,which can bring more efficiency and stability.

With special process of 6 layer thicken PCB will lower resistance, small calorific value and bigger impact resistance current.Nice optimize layout of the components and parts makes a smaller size,lighter weight and easy to build.

What do you think about this esc? very glad to hear from your feedback about that.

Also, if you are interested in this product, you can purchase from this shop: http://www.bonroytech.com/views.asp?hw_id=419
Discussion / Posted by TINGW / Aug 18, 2017 @ 10:51 PM / 2,371 Views / 1 Comments / Reply
This entry is temporarily hidden while TINGW edits it.
New Product / Posted by TINGW / Aug 16, 2017 @ 10:12 PM / 1,909 Views / 0 Comments
This entry is temporarily hidden while TINGW edits it.
Posted by TINGW | Aug 14, 2017 @ 07:06 AM | 2,197 Views
D o you still think about where can you buy the DYS's products? Do you still care about whether the original products you bought? Do you still worry about where can you buy the varied FPV products? It is not the problem now

Because I will share you a awesome hobby shop: http://www.bonroytech.com/ (Bonroy)

You can buy so much FPV racing products from there , you can get the good customer service from there, more importantly, you can receive the perfect products from there.