Shop our Airplanes Products Drone Products Sales
Alex fpv's blog View Details
Posted by Alex fpv | Jul 18, 2018 @ 11:02 AM | 1,334 Views
I have a 3Ē quad with 1408 motors and I have HQ3x5x3 props. I have been running 3s on it with out any problems and recently I tried to run 4s. Half way through the throttle the whole quad would have a shaky effect through the googles, I could also hear it vibrate a lot. This is alittle concerning bc my thought Itís the props and the props are big as I can get on it. If anybody could help me identify the problem that would be great.
Posted by Alex fpv | Apr 07, 2018 @ 12:33 PM | 908 Views
I have just gotten into micro and I find it very difficult to find a small receiver that works with spectrum. If anybody can help me find one that would be helpful.
Posted by Alex fpv | Jan 29, 2018 @ 09:14 PM | 1,550 Views
I was thinking about getting gate breakers for my 5 inch was wondering if they would be a good purchase for it. Also if they are a good quality props and if they are worth it.
Posted by Alex fpv | Jan 08, 2018 @ 04:47 PM | 1,844 Views
I have a zmr 250 frame with emax 2204 motors and I was wondering what motors would be good to upgrade and replace the ones I have and I like emax. I was thinking the 2306 race motors but I didnít know if they would fit on my frame and I heard they have a lot of thrust and are reliable motors. If anybody has any ideas on motors that would be great!
Posted by Alex fpv | Dec 08, 2017 @ 10:44 AM | 2,027 Views
I have a spectrum serial race receiver and a dx6e transmitter and i am able to bind them but cannot get any signal from the transmitter and when I go into cleanlfight and the receiver tab and try and move the switches nothing happens but I am able to bind to it. If anybody has any ideas of what the problem is please tell me
Posted by Alex fpv | Nov 09, 2017 @ 02:55 PM | 1,975 Views
I have been having some issues with my drone just falling out of the sky and I have been trying to fix it but a solder came lose and I resoldered it back on and then I notice a component was missing on the board and then flight controller (seriously dodo) started to get hot and I was wondering if it was because the component was missing. If anybody thinks it that and if I should get a new pdb? But I donít know
Posted by Alex fpv | Oct 18, 2017 @ 02:50 PM | 2,029 Views
I have just finished my first 250 frame build and was thinking about building a smaller one like around 130 or 100mm. I was hoping somebody can give me a good frame to use and the not the hardest one to work with and maybe some parts that would be the right size because, I am a little stuck on what the sizes are for the motors and the motherboard. If anybody can help I would appreciate it.
Posted by Alex fpv | Sep 03, 2017 @ 04:05 PM | 2,064 Views
I have been having a problem with the Matek pdb recently and I have been flying my drone and it has worked fine and had no crashes. But last week I went to go fly and I plugged in the battery and nothing. I have a voltage meter and checked the esc solders to see if they get any power and they donít. The lights donít light up and it doesnít beep. I have checked the xt60 connector and itís good wiTh the solder and the prongs. I really need some help I canít think of something that could cause this?
Posted by Alex fpv | Jul 27, 2017 @ 02:04 PM | 2,566 Views
Hi I am looking into fpv cameras and I am not sure which is the best one? I donít mind if itís a board camera but it is hard to angle it. I have a pic of where I would mount a camera but I am not sure if I am able to mount an non board camera on this frame. So if anybody can help me that would be great!
Posted by Alex fpv | Jul 12, 2017 @ 11:09 AM | 3,153 Views
I am building a racing drone right now and i am just getting into the hobby. I have been looking at transmitters for a while now and i found the dx6e but not sure if it is the best for a drone. what do you guys recommend.
Posted by Alex fpv | Jul 11, 2017 @ 02:07 PM | 13,720 Views
I have a omnibus and i am wonder how to connect the spectrum receiver to it. i would want to be able to use the pins if that is possible.
Posted by Alex fpv | Jun 28, 2017 @ 11:29 AM | 2,823 Views
i am on cleanflight and every time i press save and reboot it freezes on rebooting and will not save.
Posted by Alex fpv | Jun 26, 2017 @ 07:46 PM | 3,849 Views
I just got a naze32 rev 6 and I tried to flash cleanflight on it and itís said boot loader not responding. I have tried to short the boot and that didnít work. I am not sure how to use the usb driver on the home page of cleanflight .