OrtisFlow's blog - RC Groups
OrtisFlow's blog View Details
Posted by OrtisFlow | Mar 13, 2018 @ 01:39 PM | 795 Views
Hey again readers,

About my homemade motor proto while doing my tests something popped up... I let you check in the video.

You can see original bell that came with and original stator mount quality

ReadyToJam (0 min 32 sec)

Gotta fix that
Posted by OrtisFlow | Mar 13, 2018 @ 12:28 PM | 824 Views
Hey readers,

had some motor very low quality I had bought 27$ a pack of 4....
I've swapped bells with my old racerstar edition limited, also new ball bearings and adjustment...
And I did cut the motor bases to look like naked bottom...
Flies like there are brand new rotor....
Now I need to put back top frame mount and fpv equipment!

Some video footage soon.
Posted by OrtisFlow | Mar 10, 2018 @ 03:21 PM | 776 Views
Hey again readers,

I did try that butter bar and well it was a bad exp for me.
I had ~fixed the vibrations in the fpv feed at low throttle with Betaflight.
But Butterflight brought back the vibrations; it was almost unflyable, it's lot more vibration than with Betaflight...
I switched back to Betaflight for now. I'll give that Butter another try later with some brand new equipment to try it out correctly.
Posted by OrtisFlow | Mar 10, 2018 @ 03:12 PM | 704 Views
Hey readers,

Today I've improved my drone shed as you can see on the picture.

Posted by OrtisFlow | Mar 08, 2018 @ 01:50 PM | 1,079 Views
Hey readers,

I did watch Joshua Bradwell's video about butterflight and decided to give it a try.

Feedback tomorrow.
Posted by OrtisFlow | Mar 07, 2018 @ 04:51 PM | 790 Views
Hey again readers,

I had to share this, cuz it still impresses me after some flights....
That sick I did hit winding with a plier while swapping ball bearings and it was cut...
Thought I was about to order a new motor but I did try to solder before.... and guess what it works
Posted by OrtisFlow | Mar 07, 2018 @ 04:43 PM | 750 Views
Hey readers,

That one is just to remind me good time with my cobra.
Posted by OrtisFlow | Mar 06, 2018 @ 02:33 PM | 697 Views
Hey readers,

Did some footage with the new firmwares to my R25 Sunnysky now using C-H_90 with a startup power of 1.0.
Still have some propwash but low throttle oscillation are almost gone...

UPDATE It turned out to be bad pids... More info soon.

Switching deadtime (3 min 57 sec)

Quad setup:
606 grams
Realacc X5r frame
Daldrops 5046*3 C
Sunnysky Edge R2205 2300kv
Sunnysky R25A
Luxx F3 v1
Frsky xm+
Eachine TX03
Foxeer Cam
Infinity 1.3Ah 90c
Gopro session
Posted by OrtisFlow | Mar 04, 2018 @ 05:25 AM | 1,664 Views
Hey readers,

Crappy low throttle motor oscillation (3 min 51 sec)

Found out my R25 sunnysky escs are in cause.... did update them to blheli 16.7 and used c-h_90 over c-h_15.
They works fine using that timing they just lot more smooth now with none low throttle oscillation ....

Will show that in the next video.
Posted by OrtisFlow | Feb 01, 2018 @ 03:19 PM | 1,889 Views
WTF FACKSAFE!!! (1 min 2 sec)

Feeling like I'm gonna use my remaining stuff and stop that waste quicker than expected...
Posted by OrtisFlow | Jan 29, 2018 @ 06:04 PM | 981 Views
Hey readers,

Took some break from drones... then watched some skitzo videos and I'm back!

I've flew a day ago, it wasnt that bad after not having a flight for like 2 good months...

I felt like I was using too much rate... so I have dropped it down from 1200 to 770.

It's way better that way... I dunno why I went with 1200 since the beginning... it was mistake.

Also found out that 2 escs and a motor died from my last crash with my RidgeRacer (2 months ago...) The combo esc/motor flew only 2 lipos...

Mitigating that atm....

Maybe some videos soon...
Posted by OrtisFlow | Nov 25, 2017 @ 07:43 AM | 2,098 Views
Well a while ago I bought some 30A BumpBee S with the description telling it was working with multishot and oneshot...

Then tried them and I had roll of death using both multishot and oneshot....

Then like a day ago came the idea why not dshot.. then I did some research around the escs... and discovered that mine came with a cap removed....

So they are only able to run using DSHOT...

No need to say it is TOP ESCs! Big fets and super smooth using BLHELI_S J_H_90

Feedback soon!!!

They doesn't work, rolling to death (bending my props, stressing my frame...) W.T.F :/
Posted by OrtisFlow | Nov 18, 2017 @ 07:18 AM | 1,657 Views
Greetingz readers,

Yesterday went the backyard field to train myself a lil bit more with that new way to fly...

Flew 2 lipos... the second one was his last... A R2205 2500kv SunnySky motor fried while flying!!!

So crash and almost lost GoPro...

The motor has now a freaking bad smell... and it has builtin braking forever now .... ( copper wires wielded together... )

I question seriously the quality of these motors... It was my fourth flights with them and never crashed...

My First combo didn't last long too... was an R2205 2300kv... I crashed them in a grass field one times they were already unusable after this (one crash YEA Ball bearings from 3 motors were deads)...

In other side my PULSO COBRA CP GOLDEN LASTED WAY MORE THAN THAT.... I'm still flying with them they have crashed a lot!!! even on ASPHALT!!!

Just swapped ball bearings and they still flies smooth....

To me it's obvious... QUALITY of THESE SunnySky R2205 Is freaking questionable...

Top perfromance : 8/10
Quality: 5/10
Look: 7/10
Durability: 2/10

Having a bad time...
Posted by OrtisFlow | Nov 15, 2017 @ 08:01 AM | 2,327 Views
Greetingz again readers,

It does! (4 min 10 sec)

Have fun go fly!
Posted by OrtisFlow | Nov 15, 2017 @ 03:10 AM | 2,440 Views
Greetingz readers!

If you look for some quality ball bearing...


These are my best from all those I did test since a year now...

Freaking durable... Crashed lot but they are still smooth...

I do use them for my PULSO COBRA CP GOLDEN 2205... original one are too expensive...

Have fun, go fly & pick up nice gear

(A YEAR FLYING KWADS!!! I'm gonna open a bottle!!!)
Posted by OrtisFlow | Nov 05, 2017 @ 03:07 PM | 1,503 Views
Greetingz readers,

It was a test, I got inspired from Sean FPV, but had none 6S battery :/

I had to make my own xp about it. So I did and there the result.

GoPro mount+GoPro is around 140gr more added to the kwad 493gr...

The props used was a mistake...

Shud have used 2 blades high pitched props...

Anyway 4S isn't enouf... 5S would be better and I intimately guess 6S would be just perfect...

Without GoPro mount and GoPro using Gemfan 5046 dual blade on 4S it's a bullet! But flight time reduced to 2mins...

I'll make some DVR footage soon...

Looks like you got an update from my Ridge Racer!

Have fun, go fly!
Posted by OrtisFlow | Nov 04, 2017 @ 05:56 AM | 1,889 Views
Greetingz again readers,

Just wanted to show you some updated pictures.

Have fun, go fly!
Posted by OrtisFlow | Nov 04, 2017 @ 04:20 AM | 2,113 Views
Greetingz readers,

Bought an EWRF E709TM3 with FC mounting holes

First look VERY OK.

Then I did try to config the VTX to fit the default channel from my predator goggle...

And surprise...

I did believe that the number blinking after band and channel was just an error....

Then discovered on my goggle I was able to pick many frequencies sending the video signal...

As you will discover bands naming is wrong... You should refer to the frequency blinking after band and channel.

I'll buy a new one finally!!!

Have fun, go fly! (and learn from your mistakes...)
Posted by OrtisFlow | Oct 27, 2017 @ 10:10 AM | 1,862 Views
Greetingz readers,

Some legit pictures I've done from my kwads...

Maybe way better than reading the spam reviews around...

Dunno... It's up to you.

Have fun, go fly!
Posted by OrtisFlow | Oct 24, 2017 @ 07:32 AM | 2,167 Views
Greetings readers,

I dunno how is the story with your Runcam3 but mine died herself just by staying on the desk...

I never had an hard crash... The camera just look like brand new... But it's dead after only 2 months~ ...

So I have opened the camera to see if something is noticeable... and yea... both batteries "puffed!"

One of them spread chemical outside battery...

Finally bought a GoPro session, I now think I shud have done this first!!!

To the next times, readers!