ltwvince's blog - RC Groups
ltwvince's blog View Details
Posted by ltwvince | Sep 10, 2017 @ 12:05 PM | 1,820 Views
Boldclash BWHOOP B-03 Pro Flight Test (3 min 47 sec)




Disclaimer (inspired from @SoloProFan and @SeByDocky): Product specifications and quality may vary at the manufacturer's discretion, and are beyond my influence. I cannot guarantee you will get a product that performs exactly the same as seen and described in this review. Please, NO savage affiliate links!


INTRODUCTION
Boldclash BWHOOP B-03 Pro is the upgraded next generation of tiny whoop size micro quadcopter that feature 7x16mm motors instead of the usual 6x15mm motors. First glance, it just look like any other tiny whoop with the similar motor to motor size of 65mm. It comes in single color option with translucent frame and black/grey theme.


BOX CONTENT
+ 1 x Boldclash BWHOOP B-03 Pro Micro Quadcopter with Canopy
+ 1 x Transmitter (Remote Control)
+ 1 x 3.7V 1S 260mAh 35C Battery with JST-PH 2.0 Connector
+ 4 x Spare 4-Blades Propellers (2 x CW & 2 x CCW)
+ 1 x USB Battery Charger
+ 1 x Screwdriver
+ 1 x User Manual (English / Chinese)




OVERVIEW
This Boldclash BWHOOP B-03 Pro has no Barometer built into its Flight Controller unlike its little brother B-03 which I had reviewed earlier, you can find the full review HERE. Like his younger brother, it also comes with easily replaceable motor plug by just unplugging the Micro JST 1.25mm connector, no more messing up with soldering iron. There is a programmable port for Silverware firmware modification as well. Powered by 7x16mm...Continue Reading
Posted by ltwvince | Aug 03, 2017 @ 11:45 AM | 2,437 Views


Disclaimer (inspired from @SoloProFan and @SeByDocky): Product specifications and quality may vary at the manufacturer's discretion, and are beyond my influence. I cannot guarantee you will get a product that performs exactly the same as seen and described in this review. Please, NO savage affiliate links!


INTRODUCTION
Eachine TX01S is one of the light and small 5.8GHz 25mW AIO VTX/Camera split type combo found on the market with a whip antenna instead of the clunky CL antenna. VTX module comes with 48 Channels including race band. The camera module comes in NTSC format with 600 TVL and 120° viewing angle.


BOX CONTENT
+ 1 x Eachine TX01S 25mW 48 Channels VTX + Camera Split Type with 100mm Wires
+ 1 x VTX with Whip Antenna and power input wires with Micro JST 1.25mm Male Connector
+ 1 x 600TVL, 120° Viewing Angle Camera
+ 1 x Micro JST 1.25mm Female to Micro Losi/Walkera Connector (70mm)
+ 1 x Camera Lens Cap
+ 1 x User Manual (English/Chinese)




OVERVIEW
Just like any of the current trend of AIO VTX + Camera that we find on the market that comes in form of split type where we don’t need to perform the complicated mullet modification. You may want to shorten the lengthy 100mm signal/power wires if you’re using this with any Tiny Whoop built.


UNBOXING
Mine is the 25mW version while there is another 200mW version, TX02S.

...Continue Reading
Posted by ltwvince | Jul 20, 2017 @ 11:41 AM | 2,486 Views


Disclaimer (inspired from @SoloProFan and @SeByDocky): Product specifications and quality may vary at the manufacturer's discretion, and are beyond my influence. I cannot guarantee you will get a product that performs exactly the same as seen and described in this review. Please, NO savage affiliate links!


INTRODUCTION
Kingkong 90GT is a true X frame type 90mm quad that comes pre-built out of the box. All you need is just a compatible transmitter for BNF version and plus a receiver for PNP version. There are three different flavors to choose from such as Frsky, DSM and PNP (No Receiver). Mine comes in PNP flavor. I will be flying this quad with my LemonRX DSMX Satellite receiver and Devo 12E transmitter.


BOX CONTENT
+ 1 x Kingkong 90GT Micro Quadcopter consist of:
+ 1 x Kingkong SP Racing F3 Flight Controller with SBUS/DSM Cable
+ 1 x Kingkong BLHeli_S 4-in-1 3A ESC with PDB/BEC (DSHOT Compatible)
+ 4 x Kingkong 1103 7800KV Brushless Motors
+ 1 x Kingkong Q25 5.8GHz 25mW 16 Channels Mini VTX with Whip Antenna
+ 1 x 150 degree FOV 800TVL Camera + Lens Cap
+ 1 x Rubber Band
+ 1 x Kingkong 7.4V 2S 350mAh 35C Battery with JST Connector and Balancing Lead
+ 8 x Kingkong 1935 Tri-Blades Propellers (4 x CW & 4 x CCW) + Screws
+ 1 x 2.3 inch White Propeller Guard with screws and washer
+ 1 x Micro USB Cable for FC and ESC Programming
+ 1 x PWM/PPM Cable
+ 2 x Extra Rubber Band
+ 1 x Propeller Removal Tool
+ 1 x Storage Box
+ 1 x Kingkong 90GT QC Report...Continue Reading
Posted by ltwvince | Jul 11, 2017 @ 07:18 AM | 14,454 Views


Disclaimer (inspired from @SoloProFan and @SeByDocky): Product specifications and quality may vary at the manufacturer's discretion, and are beyond my influence. I cannot guarantee you will get a product that performs exactly the same as seen and described in this review. Please, NO savage affiliate links!


INTRODUCTION
Boldclash BWHOOP B-03 is the next generation of tiny whoop size micro quadcopter that feature 7x16mm motors instead of the usual 6x15mm motors. First glance, it just look like any other tiny whoop with the similar motor to motor size of 65mm. It comes with two color option, Orange and Blue.


BOX CONTENT
+ 1 x Boldclash BWHOOP B-03 Micro Quadcopter with Canopy
+ 1 x Transmitter (Remote Control)
+ 1 x 3.7V 1S 260mAh Battery with JST-PH 2.0 Connector
+ 4 x Spare 4-Blades Propellers (2 x CW & 2 x CCW)
+ 1 x USB Battery Charger
+ 1 x Screwdriver
+ 1 x User Manual (English)




OVERVIEW
This Boldclash BWHOOP B-03 has Barometer built into its Flight Controller and all motors are easily replaceable by just unplugging the Micro JST 1.25mm connector, no more messing up with soldering iron. There is a programmable port for Silverware firmware modification. Powered by 7x16mm 53500 RPM motors and equipped with 4-blades 31mm propellers.


UNBOXING
My Boldclash BWHOOP B-03 box came in crushed on the side but everything seems fine.

...Continue Reading
Posted by ltwvince | Mar 13, 2017 @ 05:54 AM | 6,323 Views


Disclaimer (inspired from @SoloProFan and @SeByDocky): Product specifications and quality may vary at the manufacturer's discretion, and are beyond my influence. I cannot guarantee you will get a product that performs exactly the same as seen and described in this review. Please, NO savage affiliate links!


INTRODUCTION
Boldclash F-02 is currently one of the lightest and smallest split type 5.8GHz 25mW AIO Camera VTX on the market with a whip antenna instead of the clunky CL antenna. VTX module comes with 48 Channels including race band. The camera module has the option to switch between PAL and NTSC. Another extra feature the camera module has to offer is the ability to flip/invert the camera view.


BOX CONTENT
+ 1 x Boldclash F-02 Camera + VTX + Connection Cable
+ 1 x Camera Lens Cap
+ 2 x Extra 5.8GHz Whip Antenna
+ 1 x User/Operation Manual (English)




OVERVIEW
Unlike the normal AIO Camera VTX we find on the market today, this Boldclash F-02 comes in form of split type just like the mullet modification that everyone is trying to achieve with the normal AIO. Now you don’t need to perform any mullet modification. The only modification you may need to do is to replace the power input plug to either Micro JST 1.25mm male plug for standardization or just direct solder to your FC power source.


UNBOXING

...Continue Reading
Posted by ltwvince | Mar 09, 2017 @ 05:42 AM | 7,206 Views


Disclaimer (inspired from @SoloProFan and @SeByDocky): Product specifications and quality may vary at the manufacturer's discretion, and are beyond my influence. I cannot guarantee you will get a product that performs exactly the same as seen and described in this review. Please, NO savage affiliate links!


INTRODUCTION
Boldclash 6x15mm 18000KV Coreless Motor is currently the fastest motor available from TMART for your Tiny Whoop.


PACKAGE CONTENT
+ 2 x CW c/w 70mm wire and Micro JST 1.25mm Connector
+ 2 x CCW c/w 70mm wire and Micro JST 1.25mm Connector
+ 4 x Micro JST 1.25mm Male Connector
+ 1 x Simple User Instruction (English)

[

...Continue Reading
Posted by ltwvince | Mar 07, 2017 @ 04:33 AM | 6,918 Views


Disclaimer (inspired from @SoloProFan and @SeByDocky): Product specifications and quality may vary at the manufacturer's discretion, and are beyond my influence. I cannot guarantee you will get a product that performs exactly the same as seen and described in this review. Please, NO savage affiliate links!


INTRODUCTION
Eachine E010S is yet another Tiny Whoop clone that comes pre-built out of the box. All you need is just a compatible transmitter and you will be flying in no time. These BNF comes in three different flavors such as Frsky, Flysky and DSM. Mine comes with DSM2.


BOX CONTENT
+ 1 x Eachine E010S Micro Quadcopter
+ 1 x 5.8GHz 25mW 40 Channels AIO VTX Camera with CL Antenna + Lens Cap
+ 1 x Eachine 150mAh 3.7V 45C Battery with Micro Losi/Walkera Connector
+ 1 x USB Battery Charger
+ 4 x Extra 4-Blades Propellers (2 x CW & 2 x CCW)
+ 1 x Propeller Removal Tool
+ 2 x Rubber Bands
+ 2 x 3M Double Sided Foam Tape
+ 1 x Eachine E010S Manual (Chinese / English)




OVERVIEW
This Eachine E010S uses new lighter and softer translucent frame with angled struts. The SP Racing F3 Evo Brush Flight Controller comes with built-in with DSM2 RX and CleanFlight 1.13.0 pre-installed. Powered by 6mm x 15mm 59000 RPM coreless motor and equipped with 4-blades propellers. It also comes with a 5.8GHz 25mW AIO VTX Camera combo for your FPV needs.


UNBOXING
Strangely that I was given QX100 box but the content is Eachine E010S.

...Continue Reading
Posted by ltwvince | Mar 03, 2017 @ 07:19 AM | 7,318 Views


Disclaimer (inspired from @SoloProFan and @SeByDocky): Product specifications and quality may vary at the manufacturer's discretion, and are beyond my influence. I cannot guarantee you will get a product that performs exactly the same as seen and described in this review. Please, NO savage affiliate links!


INTRODUCTION
Makerfire MicroFPV is yet another Tiny Whoop clone that comes pre-built out of the box. All you need is just a DSM2 compatible transmitter and you will be flying in no time.


BOX CONTENT
+ 1 x Makerfire MicroFPV 64mm Micro Quadcopter
+ 1 x 5.8GHz 25mW 48 Channels AIO VTX Camera with Whip Antenna + Lens Cap
+ 1 x Canopy with built-in 10 Degree Tilt Camera Holder
+ 1 x Crazepony 200mAh 3.7V Battery
+ 1 x Battery Foam Adaptor
+ 1 x USB Battery Charger
+ 1 x Makerfire Service Card




OVERVIEW
This Makerfire Micro FPV uses the same frame as JJRC H36. The SP Racing F3 Evo Brush Flight Controller comes with built-in with DSM2 RX and BetaFlight 3.0.1 pre-installed. Powered by 6mm x 15mm 65000 RPM coreless motor and equipped with 4-blades propellers. It also comes with a 5.8GHz 25mW AIO VTX Camera combo for your FPV needs.


UNBOXING

...Continue Reading
Posted by ltwvince | Jan 24, 2017 @ 03:02 AM | 6,792 Views


Disclaimer (inspired from @SoloProFan and @SeByDocky): Product specifications and quality may vary at the manufacturer's discretion, and are beyond my influence. I cannot guarantee you will get a product that performs exactly the same as seen and described in this review. Please, NO savage affiliate links!


INTRODUCTION
This Eachine E50 is a Wifi enabled with camera quad that are aiming for people who like selfie. All you need is a phone and app to control the quad. It comes in two colors, black and white. This selfie quad with arm folded is just a slightly bigger than my Sony Xperia Z5 Compact.



...Continue Reading
Posted by ltwvince | Jan 14, 2017 @ 09:43 AM | 7,515 Views


Disclaimer (inspired from @SoloProFan and @SeByDocky): Product specifications and quality may vary at the manufacturer's discretion, and are beyond my influence. I cannot guarantee you will get a product that performs exactly the same as seen and described in this review. Please, NO savage affiliate links!

INTRODUCTION
This Eachine QX90C comes shining in its bright yellow plastic frame that differ itself from all its other QX series brethren. There are two main options you can choose from. First is the ARF version that doesn’t comes with any RX and BNF version comes in three different flavors such as Frsky, Flysky and DSM2. Mine is a BNF version comes with DSM2.



...Continue Reading
Posted by ltwvince | Dec 23, 2016 @ 01:27 AM | 7,544 Views


Disclaimer (inspired from @SoloProFan and @SeByDocky): Product specifications and quality may vary at the manufacturer's discretion, and are beyond my influence. I cannot guarantee you will get a product that performs exactly the same as seen and described in this review. Please, NO savage affiliate links!


INTRODUCTION
Chaoli CL-615 Upgraded 6x15mm 59000 RPM Coreless Motor is currently the fastest motor available from Banggood for your Tiny Whoop.




PACKAGE CONTENT
+ 2 x CW c/w 80mm wire and Micro JST Connector
+ 2 x CCW c/w 80mm wire and Micro JST Connector

...Continue Reading
Posted by ltwvince | Nov 19, 2016 @ 02:53 AM | 9,162 Views



Disclaimer (inspired from @SoloProFan and @SeByDocky): Product specifications and quality may vary at the manufacturer's discretion, and are beyond my influence. I cannot guarantee you will get a product that performs exactly the same as seen and described in this review. Please, NO savage affiliate links!


INTRODUCTION
Boldclash F-01 is currently one of the lightest and smallest 5.8GHz 25mW AIO FPV cameras on the market with a whip antenna instead of the clunky CL antenna. Come with 48 Channels including race band. It has the option to switch between PAL and NTSC. Another extra feature this AIO offer is the ability to flip/invert the camera view.




BOX CONTENT
+ 1 x Boldclash F-01 c/w 80mm wire and Micro JST Connector
+ 1 x Camera Lens Cap
+ 2 x Extra 5.8GHz Whip Antenna
+ 1 x User/Operation Manual (English)

...Continue Reading
Posted by ltwvince | Nov 18, 2016 @ 05:40 AM | 13,568 Views
Hi Guys and Gals,

Here is my simple guide to build a custom SilverWhoop.

Tools Required
1. Solder Iron
2. Solder Iron Tin and Flux
3. Magnifying Glass (optional)
4. Any small gauge wires you may have
5. Hobby or pen knife
6. Patience and time


Items / Parts Required
1. Frame
Furibee F36 Frame or JJRC H36 Frame or Eachine E010S Frame or Eachine E010 Mini Frame
2. Propellers
Eachine E010S 4-Blade Propellers or Eachine E010 Mini 4-Blade Propellers or JJRC H36 4-Blade Propellers
3. Flight Controller
Eachine H8 Mini or Eachine H8S Mini or Floureon H101 (Out of stock) * We just need the FC to run Silverware
4. AIO Camera VTX
Boldclash F-01 5.8G 25mW AIO or Boldclash F-02 5.8G 25mW AIO Split Type or FX798T 5.8G 25mW AIO or any other AIO Camera VTX
5. FPV Camera Mount for FX797T/798T (optional)
6. Batteries
Eachine H8 Mini 260mAh 30C Battery Upgrade (5pcs) or Floureon H101 206mAh 30C Battery Upgrade (5pcs)
7. Motors
Boldclash 6x15mm 18000KV Coreless Motor (4pcs) or Boldclash 6x15mm 18000KV Coreless Motor (20pcs) or
Racerstar 6x15mm 59000RPM Coreless Motor - Red or Racerstar 6x15mm 59000RPM Coreless Motor - Black or
Chaoli 6x15mm 59000RPM Coreless Motor or Chaoli 6x15mm Coreless Motor or
Furibee F36 Motor or BayangToys X9 Motor (Out of stock)
8. Micro JST Connector 1.25mm 2-pin


Getting Started
1. Prepare the frame by cutting away those screws mounting for easier mounting with loom bands.




2. Next is to cut away part of this section to...Continue Reading
Posted by ltwvince | Nov 17, 2016 @ 10:16 PM | 7,670 Views
Hi Guys and Gals,

Here is my simple guide to modify, upgrade and get your Eachine E010 to FPV ready in no time.

Tools Required
1. Solder Iron
2. Solder Iron Tin and Flux
3. Magnifying Glass (optional)
4. Hobby or pen knife
5. Patience and time

Items / Parts Required
1. Eachine E010 Mini
2. Boldclash F-01 5.8G 25mW AIO or FX798T 5.8G 25mW AIO or any other AIO Camera VTX
3. FPV Camera Mount for FX797T/798T
4. H8 Mini 260mAh 30C Battery Upgrade
5. BayangToys X9 Motor or Boldclash 6x15mm Coreless Motor or Chaoli 6x15mm Coreless Motor or Chaoli 6x15mm 59000RPM Coreless Motor (optional)
6. Micro JST Connector 1.25mm 2-pin (optional)
7. FQ777-124 TX Sticks (optional)


FPV Equipment
1. FPV Monitor or FPV goggles with video receiver and antenna
2. DVR such as the Eachine ProDVR for flight recording (optional)

Getting Started
1. Remove the E010 canopy and make sure you aware of the motor polarity marking as the prints on the board are wrongly printed for the front left and rear right motors. We will need to unsolder all the motors wiring and remove the FC from the frame.




2. Next is to remove the Crystal from the top of the FC and solder it to the bottom of the FC. Put a dab of hot glue to secure the Crystal.

This way, you can use your current Inductrix camera mount that you have or get one from BG without the need of customizing the camera mount.

Before




After

...Continue Reading
Posted by ltwvince | Oct 05, 2016 @ 09:43 AM | 9,327 Views
Hi Guys and Gals,

Here is my simple guide to rescue those who had their H8 Mini Green Board and H101/H8S Board CLK & DAT pad broken due to some unforeseen reason like myself.

Don't do this process if you rushing as this may be your last chance to salvage this board unless you want to solder directly to the MCU.

Tools Required
1. Fine Tip Solder Iron
2. Solder Iron Tin and Flux
3. Magnifying Glass (optional)
4. 0.38mm Enamelled Wire or any thin wires you may have
5. Hobby or pen knife
6. Lots of patience and time


An overview of the GigaDevice GD32F130 Pinout




Identify the Hidden CLK & DAT Traces

H8 Mini Green Board

[


H101 / H8S Mini CLK

...Continue Reading