djmoose's blog View Details
Posted by djmoose | Apr 30, 2021 @ 04:17 PM | 5,348 Views
Let's attach the rudder and elevator with Robart pin hinges in the same fashion as we did with the ailerons. We'll also install the respective servos and pushrods to connect everything up.

How to attach the Rudder and Elevators on the 92" Black Horse Gilmore Red Lion ARF (12 min 12 sec)

Posted by djmoose | Apr 24, 2021 @ 08:02 AM | 7,890 Views
How to attach the Landing Gear of the 2350mm Black Horse Gilmore Red Lion - Wedell-Williams 44 (11 min 40 sec)


I'll show you how to attach the landing gear and tail wheel in this episode. Also, a special bonus, I ordered the extra set of wheel pants from @MotionRC and there was a pleasant surprise of an extra spare piece I was not expecting. Check out the end of the video to see what it was!

About the real NR61Y:
"The gear was attached at the wing root area, projecting outward at an angle of 10 degrees to prevent them from buckling inward. The gear struts were attached to the wheel axle on the inside of the wheel so that the wheels and covering were parallel to the vertical plane or Z-axis. These factors allowed for an enhanced performance in crosswind landings. Goodrich low-pressure tired provided shock absorption." - page 29 - Wedell-Williams Air Service

About NR536V (#92 Miss New Orleans)
No. 92 would also be a Model 44 with outward appearance very similar to NR-278V. However, the landing gear legs extended from the wings in almost a straight line while No. 44 angled out a bit.
Posted by djmoose | Apr 16, 2021 @ 04:41 PM | 7,586 Views
Available at Legend Hobby: https://www.legendhobby.com/product/...r-care-yak-11/

Enjoy this relaxing montage of videos and photos of this beautiful Seagull Perestroika. You might think I went a bit overboard...but I had a BLAST creating this mini movie. I hope this conveys how I look at airplanes...and I hope that this shows off the beauty and style of this Reno racer.

Relax with the Seagull Model Reno Air Care Yak-11 - Perestroika Build Finale Mini Movie - Chapter 7 (6 min 47 sec)

Posted by djmoose | Apr 10, 2021 @ 08:13 AM | 7,056 Views
Wing Assembly of the 92" Black Horse Gilmore Red Lion ARF - Wedell-Williams Model 44 - Roscoe Turner (19 min 10 sec)


Let's glue the ailerons with pin hinges, install the servo, measure the pushrod, and run the servo extension in this first build episode of the 92" Gilmore from Black Horse Models and Motion RC!

"Don Young stood at one end of the field. Harry Williams and Roscoe Turner positioned themselves at the opposite end, a distance of one mile. Their stopwatches were synchronized to clock Jimmie's speed. Near the completion of his pass, something went terribly wrong. Aileron flutter or buzz apparently progressed to wing flutter. This caused the left wing to collapse when its guy wires snapped under the stress. The individually operated ailerons, designed by Jimmie, helped him keep the ship from rolling too fast about its own axis. This delayed the inevitable tumbling of the plane and allowed him time to unfasten his seat belt and bail out." - page 32 - Wedell-Williams Air Service
Posted by djmoose | Apr 10, 2021 @ 08:11 AM | 6,914 Views
Complete Walkthrough of the Hitec HFP-30 Servo Programmer (12 min 51 sec)


In depth explanation of the Hitec HFP-30 servo programmer explained and demonstrated for you.

I explain in detail both the servo testing mode and the servo programming mode of the HFP-30 programmer utilizing a Hitec brushless 9831 and one of the newer D-Series D951TW servos. If you're confused on exactly what the sync port does, I'll explain that as well.
Posted by djmoose | Mar 28, 2021 @ 09:46 AM | 9,542 Views
Unboxing of Black Horse Gilmore Red Lion 2350mm (92.5") ARF - Wedell-Williams Model 44 (16 min 30 sec)


Time to unbox the 92" Gilmore Red Lion from Black Horse! (plus a bit of footage of the REAL Wedell-Williams NR61Y which is on display at the Crawford Aviation Museum in Cleveland, Ohio.

NR61Y was born in Patterson, Louisiana in 1932. She was a pretty girl with a sleek, smooth NACA cowl housing her chesty Pratt & Whitney R-985. Roscoe Turner flew her to California for the start of the 1932 Bendix race in an unpainted condition. His mechanic and right hand, Don Young, not only had to build her, but paint her in a dark hangar literally just prior to race time. The colors she wore for that racing season were the most famous of all the Wedell paint schemes—silvery crème with red and black trim—and race #121.

Nicknamed in a burst of creativity as the "Gilmore Red Lion," Turner flew her to third place behind Jim Haizlip in the Wedell-Williams #92 (NR536V) and Jimmy Wedell in #44 (NR278V). Poor Roscoe placed third in the Thompson Trophy, as well, trailing Jimmy Doolittle in the Gee Bee R-1 and Jimmy Wedell in #44.

I'm very excited to share this build series with all of you!

50cc Gilmore Red Lion ARF by Black Horse Models (@MotionRC): https://bit.ly/3pCsW1y

HobbySquawk Forum Thread - https://bit.ly/39gQNxW
FlyingGiants Forum Thread - https://bit.ly/2PeXlpI

Setup:
Dualsky GA6000.9 160kv Electric Motor - https://bit.ly/3suhkiy
...Continue Reading
Posted by djmoose | Mar 05, 2021 @ 04:09 PM | 8,919 Views
My buddy, Gary, pulled his phone out for my maiden and gave permission to share. Enjoy!

Maiden Flight of my Freewing F-15C Eagle 90mm High Performance EDF Jet - Motion RC (5 min 9 sec)

Posted by djmoose | Feb 20, 2021 @ 09:47 AM | 9,822 Views
I'd like to share this video to show how you can figure out the exact settings for particular degree settings when programming a Hitec 7954/55 servo. I'll first use the HFP-25 programmer and then show the newer HFP-30 programmer.

How to program a Hitec 7954 Servo with the HFP-25 and HFP-30 (15 min 12 sec)

Posted by djmoose | Jan 23, 2021 @ 09:41 AM | 10,648 Views
Here are the chapter 4 videos of the build!

Episode 4: installing the tail control horns and preparing the elevator.
Installing the Elevator - Seagull Models Reno Air Care Yak-11 ARF - Perestroika Build - Episode 4 (15 min 50 sec)


Episode 4.1: Final installation of both stabs and rear CA hinges.
Installing the Rudder - Seagull Models Reno Air Care Yak-11 ARF - Perestroika Build - Episode 4.1 (16 min 49 sec)
...Continue Reading
Posted by djmoose | Oct 25, 2020 @ 11:47 AM | 13,028 Views
I just started a VLOG series on the Hughes H-1 V2.

Maxford USA Hughes H-1 V2 Build - Episode 1 (8 min 47 sec)
Maxford USA Hughes H-1 V2 Build - Episode 2 - Tail! (10 min 51 sec)
...Continue Reading
Posted by djmoose | Apr 28, 2017 @ 09:30 AM | 40,140 Views
A few pics of my 3DHS 120" Extra 330LX.
Posted by djmoose | Apr 28, 2017 @ 09:05 AM | 39,853 Views
My first IMAC contest of 2017 is in the books!

Thanks to the West-Salem RC club for hosting and Jtec for sponsoring this great contest!

Thank you to my sponsors, Extreme Flight and Esprit Tech/Jeti USA!

Scores can be found here:
Posted by djmoose | May 26, 2015 @ 07:05 PM | 38,204 Views
Hard work pays off! This was my 2nd ever IMAC contest and first time in Sportsman.

A great field, great weather, and even better guys to spend a weekend with.
Posted by djmoose | Jan 18, 2015 @ 06:04 PM | 38,368 Views
Hey everyone, here's the latest episode of the Official 3DHS Podcast:
The 3DHS Podcast #10 - End of Year Update

Direct Download:
http://traffic.libsyn.com/3dhobbysho...ear_Update.mp3

You can also find and subscribe to the show via itunes:
https://itunes.apple.com/us/podcast/...st/id578740936

...or you can subscribe directly via the RSS feed:
http://3dhobbyshop.libsyn.com/rss

Intro Music: Loveshadow - Takin Yo Time (The Wingman Mix)

SFX used with permission from Higher Plane Productions